| /Linux-v6.1/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-sx9324 | 6 SX9324 has 3 inputs, CS0, CS1 and CS2. Hardware layout
19 while CS1 and CS2 are used as shields.
21 [PH1], CS1 is measured, CS0 and CS2 are shield:
23 [PH2], CS2 is measured, CS0 and CS1 are shield:
25 [PH3], CS1 and CS2 are measured (combo mode):
|
| D | sysfs-class-watchdog | 98 chip at CS1.
101 from (CS0->CS1, CS1->CS0) to (CS0->CS0,
102 CS1->CS1).
108 For alternate boot mode (booted from CS1 due to wdt2
|
| /Linux-v6.1/sound/soc/intel/catpt/ |
| D | dsp.c | 222 catpt_updatel_shim(cdev, CS1, CATPT_CS_STALL, val); in catpt_dsp_stall()
224 return catpt_readl_poll_shim(cdev, CS1, in catpt_dsp_stall()
234 catpt_updatel_shim(cdev, CS1, CATPT_CS_RST, val); in catpt_dsp_reset()
236 return catpt_readl_poll_shim(cdev, CS1, in catpt_dsp_reset()
265 reg = catpt_readl_shim(cdev, CS1) & CATPT_CS_LPCS; in catpt_dsp_select_lpclock()
298 catpt_updatel_shim(cdev, CS1, mask, val); in catpt_dsp_select_lpclock()
329 catpt_writel_shim(cdev, CS1, CATPT_CS_DEFAULT); in catpt_dsp_set_regs_defaults()
366 catpt_updatel_shim(cdev, CS1, CATPT_CS_SBCS(0) | CATPT_CS_SBCS(1), in catpt_dsp_power_down()
428 catpt_updatel_shim(cdev, CS1, CATPT_CS_SBCS(0) | CATPT_CS_SBCS(1), in catpt_dsp_power_up()
|
| /Linux-v6.1/drivers/staging/fbtft/ |
| D | fb_agm1264k-fl.c | 33 #define CS1 gpio.aux[1] macro
106 if (!par->CS1) { in verify_gpios()
136 par->CS1 = gpio->gpio; in request_gpios_match()
185 gpiod_set_value(par->CS1, 1); in write_reg8_bus8()
189 gpiod_set_value(par->CS1, 0); in write_reg8_bus8()
388 gpiod_set_value(par->CS1, 0); in write_vmem()
|
| /Linux-v6.1/Documentation/devicetree/bindings/memory-controllers/ti/ |
| D | emif.txt | 39 - cs1-used : Have this property if CS1 of this EMIF
41 part attached to CS1, it should be the same type as the one on CS0,
|
| /Linux-v6.1/arch/arm/boot/dts/ |
| D | intel-ixp46x-ixdp465.dts | 26 /* 32 MB of Flash mapped in at CS0 and CS1 */
|
| D | omap3430-sdp.dts | 51 <1 0 0x28000000 0x1000000>, /* CS1: 16MB for NAND */
104 reg = <1 0 4>; /* CS1, offset 0, IO size 4 */
|
| D | armada-370-xp.dtsi | 271 <MBUS_ID(0x01, 0x5e) 0 0xffffffff>, /* CS1 */
289 <MBUS_ID(0x01, 0x5a) 0 0xffffffff>, /* CS1 */
|
| D | imx6dl-colibri-eval-v3.dts | 130 /* weim memory map: 32MB on CS0, CS1, CS2 and CS3 */
|
| D | intel-ixp42x-adi-coyote.dts | 43 * mapped in at CS0 and CS1
|
| D | armada-388-clearfog.dts | 176 * CS1:
|
| D | imx6dl-riotboard.dts | 415 MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09 0x000b1 /* CS1 */
429 MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x000b1 /* CS1 */
|
| D | imx6qdl-ts4900.dtsi | 166 MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x100b1 /* Onboard flash CS1# */
176 MX6QDL_PAD_CSI0_DAT16__GPIO6_IO02 0x100b1 /* FPGA CS1# */
|
| D | omap3-overo-common-lcd35.dtsi | 123 reg = <1>; /* CS1 */
|
| D | intel-ixp42x-arcom-vulcan.dts | 46 * mapped in at CS0 and CS1.
|
| D | armada-388-clearfog.dtsi | 232 * CS1: PIC microcontroller (Pro models)
|
| D | logicpd-som-lv-baseboard.dtsi | 65 1 0 0x2c000000 0x1000000 /* CS1: 16MB for LAN9221 */
|
| /Linux-v6.1/arch/arm64/boot/dts/microchip/ |
| D | sparx5_pcb125.dts | 61 reg = <1>; /* CS1 */
|
| /Linux-v6.1/arch/powerpc/boot/dts/ |
| D | motionpro.dts | 94 // 8-bit DualPort SRAM on LocalPlus Bus CS1
|
| D | charon.dts | 185 1 0 0xe0000000 0x04000000 // CS1 range, SM501
|
| /Linux-v6.1/Documentation/devicetree/bindings/bus/ |
| D | qcom,ebi2.txt | 18 Also CS1 and CS2 has -A and -B signals. Why they have that is unclear to me.
25 CS1 GPIO39 (A) / GPIO123 (B) 0x1b000000-0x1b800000 (8MB)
|
| D | imx-weim.txt | 36 IOMUXC_GPR1[11:0] CS0 CS1 CS2 CS3
|
| /Linux-v6.1/Documentation/devicetree/bindings/spi/ |
| D | spi-orion.txt | 51 <MBUS_ID(0x01, 0x5e) 0 0xffffffff>, /* CS1 */
|
| /Linux-v6.1/arch/arm64/boot/dts/ti/ |
| D | k3-j7200-som-p0.dtsi | 138 <0x01 0x00 0x05 0x04000000 0x800000>; /* 8MB RAM on CS1 */
|
| /Linux-v6.1/drivers/media/dvb-frontends/ |
| D | bcm3510_priv.h | 141 u8 CS1 :1; member
|
