Searched refs:subnode (Results 1 – 25 of 189) sorted by relevance
12345678
| /Linux-v5.4/Documentation/devicetree/bindings/pinctrl/ |
| D | lantiq,pinctrl-falcon.txt | 18 The name of each subnode is not important as long as it is unique; all subnodes
21 Each subnode only affects those parameters that are explicitly listed. In
22 other words, a subnode that lists a mux function but no pin configuration
24 Similarly, a pin subnode that describes a pullup parameter implies no
31 Required subnode-properties:
49 Required subnode-properties:
53 Optional subnode-properties:
|
| D | axis,artpec6-pinctrl.txt | 8 A pinctrl node should contain at least one subnode representing the pinctrl
9 groups available on the machine. Each subnode will list the mux function
10 required and what pin group it will use. Each subnode will also configure the
15 Required subnode-properties:
49 Optional subnode-properties (see pinctrl-bindings.txt):
|
| D | pinctrl-vt8500.txt | 25 configuration. Each subnode only affects those parameters that are explicitly
26 listed. In other words, a subnode that lists only a mux function implies no
27 information about any pull configuration. Similarly, a subnode that lists only
30 Required subnode-properties:
33 Optional subnode-properties:
|
| D | qcom,apq8064-pinctrl.txt | 32 The name of each subnode is not important; all subnodes should be enumerated
35 Each subnode only affects those parameters that are explicitly listed. In
36 other words, a subnode that lists a mux function but no pin configuration
38 Similarly, a pin subnode that describes a pullup parameter implies no
43 to specify in a pin configuration subnode:
|
| D | qcom,mdm9615-pinctrl.txt | 67 The name of each subnode is not important; all subnodes should be enumerated
70 Each subnode only affects those parameters that are explicitly listed. In
71 other words, a subnode that lists a mux function but no pin configuration
73 Similarly, a pin subnode that describes a pullup parameter implies no
78 to specify in a pin configuration subnode:
84 this subnode. Valid pins are:
|
| D | qcom,ipq4019-pinctrl.txt | 35 The name of each subnode is not important; all subnodes should be enumerated
38 Each subnode only affects those parameters that are explicitly listed. In
39 other words, a subnode that lists a mux function but no pin configuration
41 Similarly, a pin subnode that describes a pullup parameter implies no
46 to specify in a pin configuration subnode:
|
| D | qcom,ipq8064-pinctrl.txt | 32 The name of each subnode is not important; all subnodes should be enumerated
35 Each subnode only affects those parameters that are explicitly listed. In
36 other words, a subnode that lists a mux function but no pin configuration
38 Similarly, a pin subnode that describes a pullup parameter implies no
43 to specify in a pin configuration subnode:
|
| D | qcom,msm8660-pinctrl.txt | 32 The name of each subnode is not important; all subnodes should be enumerated
35 Each subnode only affects those parameters that are explicitly listed. In
36 other words, a subnode that lists a mux function but no pin configuration
38 Similarly, a pin subnode that describes a pullup parameter implies no
43 to specify in a pin configuration subnode:
|
| D | brcm,bcm2835-gpio.txt | 38 configuration. Each subnode only affects those parameters that are explicitly
39 listed. In other words, a subnode that lists only a mux function implies no
40 information about any pull configuration. Similarly, a subnode that lists only
61 Required subnode-properties:
65 Optional subnode-properties:
|
| D | qcom,msm8974-pinctrl.txt | 32 The name of each subnode is not important; all subnodes should be enumerated
35 Each subnode only affects those parameters that are explicitly listed. In
36 other words, a subnode that lists a mux function but no pin configuration
38 Similarly, a pin subnode that describes a pullup parameter implies no
43 to specify in a pin configuration subnode:
|
| D | qcom,msm8916-pinctrl.txt | 67 The name of each subnode is not important; all subnodes should be enumerated
70 Each subnode only affects those parameters that are explicitly listed. In
71 other words, a subnode that lists a mux function but no pin configuration
73 Similarly, a pin subnode that describes a pullup parameter implies no
78 to specify in a pin configuration subnode:
84 this subnode. Valid pins are:
|
| D | qcom,msm8960-pinctrl.txt | 67 The name of each subnode is not important; all subnodes should be enumerated
70 Each subnode only affects those parameters that are explicitly listed. In
71 other words, a subnode that lists a mux function but no pin configuration
73 Similarly, a pin subnode that describes a pullup parameter implies no
78 to specify in a pin configuration subnode:
84 this subnode. Valid pins are:
|
| D | qcom,sdm845-pinctrl.txt | 59 The name of each subnode is not important; all subnodes should be enumerated
62 Each subnode only affects those parameters that are explicitly listed. In
63 other words, a subnode that lists a mux function but no pin configuration
65 Similarly, a pin subnode that describes a pullup parameter implies no
70 to specify in a pin configuration subnode:
76 this subnode.
|
| D | qcom,apq8084-pinctrl.txt | 67 The name of each subnode is not important; all subnodes should be enumerated
70 Each subnode only affects those parameters that are explicitly listed. In
71 other words, a subnode that lists a mux function but no pin configuration
73 Similarly, a pin subnode that describes a pullup parameter implies no
78 to specify in a pin configuration subnode:
84 this subnode. Valid pins are:
|
| D | qcom,ipq8074-pinctrl.txt | 67 The name of each subnode is not important; all subnodes should be enumerated
70 Each subnode only affects those parameters that are explicitly listed. In
71 other words, a subnode that lists a mux function but no pin configuration
73 Similarly, a pin subnode that describes a pullup parameter implies no
78 to specify in a pin configuration subnode:
84 this subnode. Valid pins are:
|
| /Linux-v5.4/Documentation/devicetree/bindings/clock/ |
| D | ux500.txt | 13 - prcmu-clock: a subnode with one clock cell for PRCMU (power,
16 - prcc-periph-clock: a subnode with two clock cells for
22 - prcc-kernel-clock: a subnode with two clock cells for
28 - rtc32k-clock: a subnode with zero clock cells for the 32kHz
30 - smp-twd-clock: a subnode for the ARM SMP Timer Watchdog cluster
|
| /Linux-v5.4/Documentation/devicetree/bindings/sound/ |
| D | qcom,sdm845.txt | 25 Each subnode of sndcard represents either a dailink, and subnodes of each
36 Value type: <subnode>
41 Value type: <subnode>
46 Value type: <subnode>
|
| D | qcom,apq8096.txt | 59 Each subnode of sndcard represents either a dailink, and subnodes of each
70 Value type: <subnode>
75 Value type: <subnode>
80 Value type: <subnode>
|
| D | simple-card.txt | 39 Dai-link subnode properties and subnodes:
41 If dai-link subnode is omitted and the subnode properties are directly
42 under "sound"-node the subnode property and subnode names have to be
50 Optional dai-link subnode properties:
56 phandle to a cpu or codec subnode.
58 phandle to a cpu or codec subnode.
68 properties can be used as booleans in codec subnode to indicate if the
82 - clocks / system-clock-frequency : specify subnode's clock if needed.
|
| /Linux-v5.4/Documentation/devicetree/bindings/power/reset/ |
| D | qcom,pon.txt | 16 Optional subnode:
17 -pwrkey: Specifies the subnode pwrkey and should follow the
19 -resin: Specifies the subnode resin and should follow the
|
| /Linux-v5.4/scripts/dtc/ |
| D | dtc-parser.y | 76 %type <node> subnode
536 | subnode subnodes
540 | subnode propdef
547 subnode:
556 | DT_OMIT_NO_REF subnode
560 | DT_LABEL subnode
|
| /Linux-v5.4/drivers/staging/fieldbus/Documentation/devicetree/bindings/fieldbus/ |
| D | arcx,anybus-controller.txt | 34 for the subnode.
40 Required subnode properties:
41 - reg: Must contain the host index of the card this subnode describes:
63 /* optional subnode for a card plugged into the first host */
|
| /Linux-v5.4/Documentation/devicetree/bindings/memory-controllers/ |
| D | nvidia,tegra30-mc.txt | 26 emc-timings subnode
29 The node should contain a "emc-timings" subnode for each supported RAM type (see field RAM_CODE in
35 timing subnode
38 Each "emc-timings" node should contain a subnode for every supported EMC clock rate.
|
| /Linux-v5.4/Documentation/devicetree/bindings/perf/ |
| D | apm-xgene-pmu.txt | 22 Required properties for L3C subnode:
26 Required properties for IOB subnode:
30 Required properties for MCB subnode:
35 Required properties for MC subnode:
|
| /Linux-v5.4/Documentation/devicetree/bindings/iio/adc/ |
| D | fsl,imx25-gcq.txt | 16 Required when at least one subnode uses the this reference.
18 Required when at least one subnode uses this reference.
20 Required when at least one subnode uses this reference.
|
12345678
