Searched refs:shifter (Results 1 – 25 of 29) sorted by relevance
12
| /Linux-v5.4/Documentation/devicetree/bindings/display/ti/ |
| D | ti,tpd12s015.txt | 1 TPD12S015 HDMI level shifter and ESD protection chip
|
| D | ti,omap-dss.txt | 88 shifter). The video pipelines for the connectors are formed as follows:
|
| /Linux-v5.4/drivers/gpu/drm/omapdrm/displays/ |
| D | Kconfig | 11 tristate "TPD12S015 HDMI ESD protection and level shifter"
|
| /Linux-v5.4/Documentation/devicetree/bindings/pinctrl/ |
| D | pinctrl-mt6797.txt | 52 - mediatek,tdsel: An integer describing the steps for output level shifter
55 - mediatek,rdsel: An integer describing the steps for input level shifter
|
| D | pinctrl-mt8183.txt | 55 mediatek,tdsel: An integer describing the steps for output level shifter
58 mediatek,rdsel: An integer describing the steps for input level shifter
|
| D | pinctrl-mt7622.txt | 73 - mediatek,tdsel: An integer describing the steps for output level shifter duty
76 - mediatek,rdsel: An integer describing the steps for input level shifter duty
|
| /Linux-v5.4/arch/arm/boot/dts/ |
| D | ste-hrefv60plus.dtsi | 170 /* VMMCI level-shifter enable */
175 /* VMMCI level-shifter voltage select */
|
| D | imx6q-logicpd.dts | 99 regulator-always-on; /* Without this, the level shifter on HDMI doesn't turn on */
|
| D | am335x-bonegreen-wireless.dts | 116 /* On the BBGW this pin is routed through the level shifter (U21) that */
|
| D | ste-snowball.dts | 519 /* VMMCI level-shifter enable */
524 /* VMMCI level-shifter voltage select */
|
| D | omap3-evm-processor-common.dtsi | 195 * for bus switch SN74CB3Q3384A, level-shifter SN74AVC16T245DGGR, and 1.8V.
|
| D | imx6qdl-aristainetos2.dtsi | 621 MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x1b0b0 /* SD2 level shifter output enable */
|
| D | tegra30-apalis.dtsi | 367 * VI level-shifter direction
|
| /Linux-v5.4/arch/microblaze/ |
| D | Kconfig.platform | 19 on MicroBlaze systems without a barrel shifter.
|
| /Linux-v5.4/arch/arm64/boot/dts/xilinx/ |
| D | zynqmp-zc1751-xm015-dc1.dts | 119 /* SD1 with level shifter */
|
| D | zynqmp-zcu104-revA.dts | 174 /* SD1 with level shifter */
|
| D | zynqmp-zcu100-revC.dts | 225 /* SD0 only supports 3.3V, no level shifter */
|
| D | zynqmp-zcu111-revA.dts | 430 /* SD1 with level shifter */
|
| D | zynqmp-zcu106-revA.dts | 500 /* SD1 with level shifter */
|
| D | zynqmp-zcu102-revA.dts | 526 /* SD1 with level shifter */
|
| /Linux-v5.4/drivers/pinctrl/bcm/ |
| D | pinctrl-bcm2835.c | 989 u32 shifter; in bcm2711_pull_config_set() local
994 shifter = PUD_2711_REG_SHIFT(pin); in bcm2711_pull_config_set()
997 value &= ~(PUD_2711_MASK << shifter); in bcm2711_pull_config_set()
998 value |= (arg << shifter); in bcm2711_pull_config_set()
|
| /Linux-v5.4/Documentation/devicetree/bindings/media/ |
| D | cec-gpio.txt | 33 15 aka BCM22 (some level shifter is needed for the HPD and 5V lines!):
|
| /Linux-v5.4/drivers/video/fbdev/omap2/omapfb/displays/ |
| D | Kconfig | 17 tristate "TPD12S015 HDMI ESD protection and level shifter"
|
| /Linux-v5.4/Documentation/maintainer/ |
| D | pull-requests.rst | 107 was a need for a new set of relativity shifter drivers to
|
| /Linux-v5.4/Documentation/driver-api/serial/ |
| D | driver.rst | 71 This function tests whether the transmitter fifo and shifter
|
12
