Searched refs:port3 (Results 1 – 25 of 29) sorted by relevance
12
| /Linux-v5.4/Documentation/gpu/dp-mst/ |
| D | topology-figure-1.dot | 13 driver -> port3:e;
17 payload2:s -> port3:e;
27 port2 -> mstb3 -> {port3, port4};
28 port3 -> mstb4;
34 port2 -> mstb3 -> {port3, port4};
35 port3 -> mstb4;
50 port3 [label="Port #3";shape=oval];
|
| D | topology-figure-2.dot | 13 driver -> port3:e;
17 payload2:s -> port3:e;
28 port2 -> mstb3 -> {port3, port4};
29 port3 -> mstb4;
36 port2 -> mstb3 -> port3;
39 port3 -> mstb4;
49 port3 [label="Port #3"];
|
| D | topology-figure-3.dot | 16 driver -> port3:e;
19 payload2:s -> port3:e [penwidth=3];
30 port2 -> mstb3 -> {port3, port4};
31 port3 -> mstb4;
39 mstb3 -> port3 [penwidth=3];
42 port3 -> mstb4;
52 port3 [label="Port #3";penwidth=3];
|
| /Linux-v5.4/Documentation/devicetree/bindings/media/ |
| D | renesas,ceu.txt | 74 reset-gpios = <&port3 11 GPIO_ACTIVE_LOW>;
75 powerdown-gpios = <&port3 12 GPIO_ACTIVE_HIGH>;
|
| /Linux-v5.4/arch/mips/boot/dts/mscc/ |
| D | ocelot_pcb123.dts | 61 &port3 {
|
| D | ocelot.dtsi | 139 "port2", "port3", "port4", "port5", "port6",
158 port3: port@3 { label
|
| D | ocelot_pcb120.dts | 73 &port3 {
|
| /Linux-v5.4/include/uapi/linux/ |
| D | serial.h | 90 int port3; member
|
| /Linux-v5.4/include/sound/ |
| D | emu8000.h | 58 unsigned long port3; /* Port usually at base+0x800 */ member
|
| D | emu8000_reg.h | 18 #define EMU8000_DATA3(e) ((e)->port3)
19 #define EMU8000_PTR(e) ((e)->port3+2)
|
| /Linux-v5.4/Documentation/devicetree/bindings/usb/ |
| D | pxa-usb.txt | 10 - "marvell,enable-port1", "marvell,enable-port2", "marvell,enable-port3"
|
| /Linux-v5.4/Documentation/devicetree/bindings/net/ |
| D | mscc-ocelot.txt | 64 "port2", "port3", "port4", "port5", "port6",
|
| D | keystone-netcp.txt | 78 - sgmii port3/4 module registers (only for NetCP 1.4)
84 index #1 - sgmii port3/4 module registers
|
| /Linux-v5.4/sound/isa/sb/ |
| D | emu8000.c | 1095 hw->port3 = port + 0x800; in snd_emu8000_new()
1098 !(hw->res_port3 = request_region(hw->port3, 4, "Emu8000-3"))) { in snd_emu8000_new()
1099 …_printk(KERN_ERR "sbawe: can't grab ports 0x%lx, 0x%lx, 0x%lx\n", hw->port1, hw->port2, hw->port3); in snd_emu8000_new()
|
| /Linux-v5.4/Documentation/devicetree/bindings/pinctrl/ |
| D | renesas,rza1-pinctrl.txt | 212 port3: gpio-3 {
222 gpios = <&port3 10 GPIO_ACTIVE_LOW>;
|
| /Linux-v5.4/Documentation/devicetree/bindings/mfd/ |
| D | omap-usb-host.txt | 98 port3-mode = "ehci-phy";
|
| /Linux-v5.4/arch/arm/boot/dts/ |
| D | bcm958622hr.dts | 194 label = "port3";
|
| D | bcm958623hr.dts | 198 label = "port3";
|
| D | bcm988312hr.dts | 206 label = "port3";
|
| D | bcm958625k.dts | 234 label = "port3";
|
| D | bcm958625hr.dts | 218 label = "port3";
|
| D | imx51-zii-scu3-esb.dts | 244 label = "port3";
|
| D | sun7i-a20-lamobo-r1.dts | 160 port3: port@3 { label
|
| D | omap5-cm-t54.dts | 639 port3-mode = "ehci-hsic";
|
| D | omap5-board-common.dtsi | 693 port3-mode = "ehci-hsic";
|
12
