| /Linux-v5.4/drivers/regulator/ |
| D | arizona-ldo1.c | 195 struct arizona_ldo1 *ldo1 = config->driver_data; in arizona_ldo1_of_get_pdata() local
209 init_data->consumer_supplies = &ldo1->supply; in arizona_ldo1_of_get_pdata()
227 struct arizona_ldo1 *ldo1, in arizona_ldo1_common_init() argument
238 ldo1->supply.supply = "DCVDD"; in arizona_ldo1_common_init()
239 ldo1->init_data.consumer_supplies = &ldo1->supply; in arizona_ldo1_common_init()
240 ldo1->supply.dev_name = dev_name(parent_dev); in arizona_ldo1_common_init()
243 config.driver_data = ldo1; in arizona_ldo1_common_init()
244 config.regmap = ldo1->regmap; in arizona_ldo1_common_init()
265 ldo1->ena_gpiod = config.ena_gpiod; in arizona_ldo1_common_init()
270 config.init_data = &ldo1->init_data; in arizona_ldo1_common_init()
[all …]
|
| /Linux-v5.4/Documentation/devicetree/bindings/mfd/ |
| D | lp873x.txt | 12 buck0, buck1, ldo0 or ldo1.
26 ldo1-in-supply = <&vsys_3v3>;
59 lp8733_ldo1: ldo1 {
60 regulator-name = "lp8733-ldo1";
|
| D | wm831x.txt | 43 ldo1 : LDO1
75 ldo1: ldo1 {
|
| D | da9062.txt | 50 ldo1 : LDO_1
60 ldo1 : LDO_1
101 DA9062_LDO1: ldo1 {
|
| D | tps65912.txt | 43 ldo1 {
44 regulator-name = "ldo1";
|
| D | da9055.txt | 35 ldo1 : regulator LDO1
65 ldo1: LDO1 {
|
| D | rohm,bd70528-pmic.txt | 73 ldo1: LDO1 {
74 regulator-name = "ldo1";
|
| /Linux-v5.4/Documentation/devicetree/bindings/regulator/ |
| D | ltc3589.txt | 9 ldo1, ldo2, ldo3, and ldo4, specifying the initialization data as
13 nodes for sw1, sw2, sw3, bb-out, ldo1, and ldo2 additionally need to specify
22 0.3625 * (1 + R1/R2) V and 0.75 * (1 + R1/R2) V. Regulators bb-out and ldo1
26 and 3.2 V on LTC3589-1,2 in four steps. The ldo1 standby regulator can not
71 ldo1_reg: ldo1 {
|
| D | tps65218.txt | 8 after their hardware counterparts: dcdc[1-6] and ldo1
16 regulator-dcdc5, regulator-dcdc6, regulator-ldo1, regulator-ls3.
67 ldo1: regulator-ldo1 {
|
| D | ltc3676.txt | 9 ldo1, ldo2, ldo3, and ldo4, specifying the initialization data as
13 nodes for sw1, sw2, sw3, sw4, ldo1, ldo2 and ldo4 additionally need to specify
24 Regulators ldo1, ldo2, and ldo4 have a fixed 0.725 V reference and thus output
25 0.725 * (1 + R1/R2) V. The ldo3 regulator is fixed to 1.8 V. The ldo1 standby
|
| D | rohm,bd70528-regulator.txt | 4 - regulator-name: should be "buck1", "buck2", "buck3", "ldo1", "ldo2", "ldo3",
40 ldo1: LDO1 {
41 regulator-name = "ldo1";
|
| D | slg51000.txt | 29 ldo1
46 ldo1 {
47 regulator-name = "ldo1";
|
| D | 88pm800.txt | 14 buck1, buck2, buck3, buck4, buck5, ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7,
30 ldo1 {
|
| D | lp872x.txt | 34 LP8720 has maximum 6 nodes. (child name: ldo1 ~ 5 and buck)
35 LP8725 has maximum 9 nodes. (child name: ldo1 ~ 5, lilo1,2 and buck1,2)
61 vaf: ldo1 {
105 vcam_io: ldo1 {
|
| D | rohm,bd71837-regulator.txt | 4 - regulator-name: should be "buck1", ..., "buck8" and "ldo1", ..., "ldo7" for
6 and "ldo1", ..., "ldo6"
123 ldo1: LDO1 {
124 regulator-name = "ldo1";
|
| D | qcom,rpmh-regulator.txt | 26 PM8009: smps1 - smps2, ldo1 - ldo7
27 PM8150: smps1 - smps10, ldo1 - ldo18
28 PM8150L: smps1 - smps8, ldo1 - ldo11, bob, flash, rgb
29 PM8998: smps1 - smps13, ldo1 - ldo28, lvs1 - lvs2
|
| D | tps65217.txt | 18 tps65217: dcdc1, dcdc2, dcdc3, ldo1, ldo2, ldo3 and ldo4
50 ldo1_reg: ldo1 {
|
| /Linux-v5.4/arch/arm/boot/dts/ |
| D | dra71-evm.dts | 62 ldo1-in-supply =<&evm_5v0>;
90 lp8733_ldo1_reg: ldo1 {
92 regulator-name = "lp8733-ldo1";
108 ldo1-in-supply =<&vsys_3v3>;
138 lp8732_ldo1_reg: ldo1 {
140 regulator-name = "lp8732-ldo1";
|
| D | dra72-evm-tps65917.dtsi | 27 ldo1-in-supply = <&vsys_3v3>;
79 ldo1_reg: ldo1 {
81 regulator-name = "ldo1";
|
| /Linux-v5.4/Documentation/devicetree/bindings/sound/ |
| D | rt5668.txt | 28 - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
45 realtek,ldo1-en-gpios =
|
| D | rt5682.txt | 28 - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
45 realtek,ldo1-en-gpios =
|
| D | rt5665.txt | 35 - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
66 realtek,ldo1-en-gpios =
|
| D | rt5659.txt | 41 - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
76 realtek,ldo1-en-gpios =
|
| D | rt5640.txt | 23 - realtek,ldo1-en-gpios : The GPIO that controls the CODEC's LDO1_EN pin.
92 realtek,ldo1-en-gpios =
|
| /Linux-v5.4/include/linux/mfd/madera/ |
| D | pdata.h | 45 struct arizona_ldo1_pdata ldo1; member
|
