Searched refs:fiber (Results 1 – 18 of 18) sorted by relevance
| /Linux-v5.4/Documentation/devicetree/bindings/net/ |
| D | micrel.txt | 39 - micrel,fiber-mode: If present the PHY is configured to operate in fiber mode
41 Some PHYs, such as the KSZ8041FTL variant, support fiber mode, enabled
43 registers whether the PHY is in fiber mode, so this boolean device tree
46 In fiber mode, auto-negotiation is disabled and the PHY can only work in
|
| D | keystone-netcp.txt | 101 - mac<->fiber mode: 3
|
| /Linux-v5.4/drivers/net/fddi/ |
| D | Kconfig | 12 run over copper or fiber. If you are connected to such a network and
23 This is support for the DEC FDDIcontroller 700 (DEFZA-AA, fiber)
|
| /Linux-v5.4/drivers/net/phy/ |
| D | marvell.c | 1194 static int marvell_update_link(struct phy_device *phydev, int fiber) in marvell_update_link() argument
1201 if (fiber) { in marvell_update_link()
1218 int fiber) in marvell_read_status_page_an() argument
1259 if (!fiber) { in marvell_read_status_page_an()
1323 int fiber; in marvell_read_status_page() local
1330 fiber = 1; in marvell_read_status_page()
1332 fiber = 0; in marvell_read_status_page()
1334 err = marvell_update_link(phydev, fiber); in marvell_read_status_page()
1339 err = marvell_read_status_page_an(phydev, fiber); in marvell_read_status_page()
|
| /Linux-v5.4/drivers/net/ethernet/alacritech/ |
| D | Kconfig | 24 both copper and fiber.
|
| /Linux-v5.4/drivers/net/hippi/ |
| D | Kconfig | 12 can run over copper (25m) or fiber (300m on multi-mode or 10km on
|
| /Linux-v5.4/arch/arm64/boot/dts/hisilicon/ |
| D | hip06.dtsi | 536 media-type = "fiber";
544 media-type = "fiber";
|
| D | hip07.dtsi | 1425 media-type = "fiber";
1435 media-type = "fiber";
|
| /Linux-v5.4/drivers/net/dsa/microchip/ |
| D | ksz8795.c | 576 if (dev->ports[p].fiber) in ksz8795_w_phy()
1033 p->fiber = 1; in ksz8795_config_cpu_port()
1034 if (p->fiber) in ksz8795_config_cpu_port()
|
| D | ksz_common.h | 35 u32 fiber:1; /* port is fiber */ member
|
| /Linux-v5.4/Documentation/networking/device_drivers/intel/ |
| D | e1000e.rst | 327 between copper-based adapters and fiber-based adapters.
349 An Intel(R) Ethernet Network Adapter using fiber-based connections, however,
|
| D | e1000.rst | 341 If the board uses a fiber interface, these keywords are ignored, and the
342 fiber interface board only links at 1000 Mbps full-duplex.
|
| D | ixgb.rst | 59 | 82597EX | Intel(R) PRO/10GbE LR/SR/CX4 | - 10G Base-LR (fiber) |
60 | | Server Adapters | - 10G Base-SR (fiber) |
|
| D | i40e.rst | 370 between copper-based adapters and fiber-based adapters.
395 An Intel(R) Ethernet Network Adapter using fiber-based connections, however,
|
| D | ixgbe.rst | 100 "ifconfig ethX down" turns off the laser for 82599-based SFP+ fiber adapters.
|
| /Linux-v5.4/Documentation/networking/device_drivers/dlink/ |
| D | dl2k.txt | 204 available for fiber adapter.
|
| /Linux-v5.4/drivers/staging/most/Documentation/ |
| D | driver_usage.txt | 11 fiber optics, unshielded twisted pair cables (UTP) and coax cables. MOST
|
| /Linux-v5.4/Documentation/networking/device_drivers/cirrus/ |
| D | cs89x0.txt | 67 or fiber networks).
|
