1 // SPDX-License-Identifier: GPL-1.0+
2 /*
3 * Device driver for Microgate SyncLink GT serial adapters.
4 *
5 * written by Paul Fulghum for Microgate Corporation
6 * paulkf@microgate.com
7 *
8 * Microgate and SyncLink are trademarks of Microgate Corporation
9 *
10 * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
11 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
12 * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
13 * DISCLAIMED. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
14 * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
15 * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
16 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
17 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
18 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
19 * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
20 * OF THE POSSIBILITY OF SUCH DAMAGE.
21 */
22
23 /*
24 * DEBUG OUTPUT DEFINITIONS
25 *
26 * uncomment lines below to enable specific types of debug output
27 *
28 * DBGINFO information - most verbose output
29 * DBGERR serious errors
30 * DBGBH bottom half service routine debugging
31 * DBGISR interrupt service routine debugging
32 * DBGDATA output receive and transmit data
33 * DBGTBUF output transmit DMA buffers and registers
34 * DBGRBUF output receive DMA buffers and registers
35 */
36
37 #define DBGINFO(fmt) if (debug_level >= DEBUG_LEVEL_INFO) printk fmt
38 #define DBGERR(fmt) if (debug_level >= DEBUG_LEVEL_ERROR) printk fmt
39 #define DBGBH(fmt) if (debug_level >= DEBUG_LEVEL_BH) printk fmt
40 #define DBGISR(fmt) if (debug_level >= DEBUG_LEVEL_ISR) printk fmt
41 #define DBGDATA(info, buf, size, label) if (debug_level >= DEBUG_LEVEL_DATA) trace_block((info), (buf), (size), (label))
42 /*#define DBGTBUF(info) dump_tbufs(info)*/
43 /*#define DBGRBUF(info) dump_rbufs(info)*/
44
45
46 #include <linux/module.h>
47 #include <linux/errno.h>
48 #include <linux/signal.h>
49 #include <linux/sched.h>
50 #include <linux/timer.h>
51 #include <linux/interrupt.h>
52 #include <linux/pci.h>
53 #include <linux/tty.h>
54 #include <linux/tty_flip.h>
55 #include <linux/serial.h>
56 #include <linux/major.h>
57 #include <linux/string.h>
58 #include <linux/fcntl.h>
59 #include <linux/ptrace.h>
60 #include <linux/ioport.h>
61 #include <linux/mm.h>
62 #include <linux/seq_file.h>
63 #include <linux/slab.h>
64 #include <linux/netdevice.h>
65 #include <linux/vmalloc.h>
66 #include <linux/init.h>
67 #include <linux/delay.h>
68 #include <linux/ioctl.h>
69 #include <linux/termios.h>
70 #include <linux/bitops.h>
71 #include <linux/workqueue.h>
72 #include <linux/hdlc.h>
73 #include <linux/synclink.h>
74
75 #include <asm/io.h>
76 #include <asm/irq.h>
77 #include <asm/dma.h>
78 #include <asm/types.h>
79 #include <linux/uaccess.h>
80
81 #if defined(CONFIG_HDLC) || (defined(CONFIG_HDLC_MODULE) && defined(CONFIG_SYNCLINK_GT_MODULE))
82 #define SYNCLINK_GENERIC_HDLC 1
83 #else
84 #define SYNCLINK_GENERIC_HDLC 0
85 #endif
86
87 /*
88 * module identification
89 */
90 static char *driver_name = "SyncLink GT";
91 static char *slgt_driver_name = "synclink_gt";
92 static char *tty_dev_prefix = "ttySLG";
93 MODULE_LICENSE("GPL");
94 #define MGSL_MAGIC 0x5401
95 #define MAX_DEVICES 32
96
97 static const struct pci_device_id pci_table[] = {
98 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
99 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT2_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
100 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT4_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
101 {PCI_VENDOR_ID_MICROGATE, SYNCLINK_AC_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
102 {0,}, /* terminate list */
103 };
104 MODULE_DEVICE_TABLE(pci, pci_table);
105
106 static int init_one(struct pci_dev *dev,const struct pci_device_id *ent);
107 static void remove_one(struct pci_dev *dev);
108 static struct pci_driver pci_driver = {
109 .name = "synclink_gt",
110 .id_table = pci_table,
111 .probe = init_one,
112 .remove = remove_one,
113 };
114
115 static bool pci_registered;
116
117 /*
118 * module configuration and status
119 */
120 static struct slgt_info *slgt_device_list;
121 static int slgt_device_count;
122
123 static int ttymajor;
124 static int debug_level;
125 static int maxframe[MAX_DEVICES];
126
127 module_param(ttymajor, int, 0);
128 module_param(debug_level, int, 0);
129 module_param_array(maxframe, int, NULL, 0);
130
131 MODULE_PARM_DESC(ttymajor, "TTY major device number override: 0=auto assigned");
132 MODULE_PARM_DESC(debug_level, "Debug syslog output: 0=disabled, 1 to 5=increasing detail");
133 MODULE_PARM_DESC(maxframe, "Maximum frame size used by device (4096 to 65535)");
134
135 /*
136 * tty support and callbacks
137 */
138 static struct tty_driver *serial_driver;
139
140 static int open(struct tty_struct *tty, struct file * filp);
141 static void close(struct tty_struct *tty, struct file * filp);
142 static void hangup(struct tty_struct *tty);
143 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios);
144
145 static int write(struct tty_struct *tty, const unsigned char *buf, int count);
146 static int put_char(struct tty_struct *tty, unsigned char ch);
147 static void send_xchar(struct tty_struct *tty, char ch);
148 static void wait_until_sent(struct tty_struct *tty, int timeout);
149 static int write_room(struct tty_struct *tty);
150 static void flush_chars(struct tty_struct *tty);
151 static void flush_buffer(struct tty_struct *tty);
152 static void tx_hold(struct tty_struct *tty);
153 static void tx_release(struct tty_struct *tty);
154
155 static int ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg);
156 static int chars_in_buffer(struct tty_struct *tty);
157 static void throttle(struct tty_struct * tty);
158 static void unthrottle(struct tty_struct * tty);
159 static int set_break(struct tty_struct *tty, int break_state);
160
161 /*
162 * generic HDLC support and callbacks
163 */
164 #if SYNCLINK_GENERIC_HDLC
165 #define dev_to_port(D) (dev_to_hdlc(D)->priv)
166 static void hdlcdev_tx_done(struct slgt_info *info);
167 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size);
168 static int hdlcdev_init(struct slgt_info *info);
169 static void hdlcdev_exit(struct slgt_info *info);
170 #endif
171
172
173 /*
174 * device specific structures, macros and functions
175 */
176
177 #define SLGT_MAX_PORTS 4
178 #define SLGT_REG_SIZE 256
179
180 /*
181 * conditional wait facility
182 */
183 struct cond_wait {
184 struct cond_wait *next;
185 wait_queue_head_t q;
186 wait_queue_entry_t wait;
187 unsigned int data;
188 };
189 static void init_cond_wait(struct cond_wait *w, unsigned int data);
190 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w);
191 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *w);
192 static void flush_cond_wait(struct cond_wait **head);
193
194 /*
195 * DMA buffer descriptor and access macros
196 */
197 struct slgt_desc
198 {
199 __le16 count;
200 __le16 status;
201 __le32 pbuf; /* physical address of data buffer */
202 __le32 next; /* physical address of next descriptor */
203
204 /* driver book keeping */
205 char *buf; /* virtual address of data buffer */
206 unsigned int pdesc; /* physical address of this descriptor */
207 dma_addr_t buf_dma_addr;
208 unsigned short buf_count;
209 };
210
211 #define set_desc_buffer(a,b) (a).pbuf = cpu_to_le32((unsigned int)(b))
212 #define set_desc_next(a,b) (a).next = cpu_to_le32((unsigned int)(b))
213 #define set_desc_count(a,b)(a).count = cpu_to_le16((unsigned short)(b))
214 #define set_desc_eof(a,b) (a).status = cpu_to_le16((b) ? (le16_to_cpu((a).status) | BIT0) : (le16_to_cpu((a).status) & ~BIT0))
215 #define set_desc_status(a, b) (a).status = cpu_to_le16((unsigned short)(b))
216 #define desc_count(a) (le16_to_cpu((a).count))
217 #define desc_status(a) (le16_to_cpu((a).status))
218 #define desc_complete(a) (le16_to_cpu((a).status) & BIT15)
219 #define desc_eof(a) (le16_to_cpu((a).status) & BIT2)
220 #define desc_crc_error(a) (le16_to_cpu((a).status) & BIT1)
221 #define desc_abort(a) (le16_to_cpu((a).status) & BIT0)
222 #define desc_residue(a) ((le16_to_cpu((a).status) & 0x38) >> 3)
223
224 struct _input_signal_events {
225 int ri_up;
226 int ri_down;
227 int dsr_up;
228 int dsr_down;
229 int dcd_up;
230 int dcd_down;
231 int cts_up;
232 int cts_down;
233 };
234
235 /*
236 * device instance data structure
237 */
238 struct slgt_info {
239 void *if_ptr; /* General purpose pointer (used by SPPP) */
240 struct tty_port port;
241
242 struct slgt_info *next_device; /* device list link */
243
244 int magic;
245
246 char device_name[25];
247 struct pci_dev *pdev;
248
249 int port_count; /* count of ports on adapter */
250 int adapter_num; /* adapter instance number */
251 int port_num; /* port instance number */
252
253 /* array of pointers to port contexts on this adapter */
254 struct slgt_info *port_array[SLGT_MAX_PORTS];
255
256 int line; /* tty line instance number */
257
258 struct mgsl_icount icount;
259
260 int timeout;
261 int x_char; /* xon/xoff character */
262 unsigned int read_status_mask;
263 unsigned int ignore_status_mask;
264
265 wait_queue_head_t status_event_wait_q;
266 wait_queue_head_t event_wait_q;
267 struct timer_list tx_timer;
268 struct timer_list rx_timer;
269
270 unsigned int gpio_present;
271 struct cond_wait *gpio_wait_q;
272
273 spinlock_t lock; /* spinlock for synchronizing with ISR */
274
275 struct work_struct task;
276 u32 pending_bh;
277 bool bh_requested;
278 bool bh_running;
279
280 int isr_overflow;
281 bool irq_requested; /* true if IRQ requested */
282 bool irq_occurred; /* for diagnostics use */
283
284 /* device configuration */
285
286 unsigned int bus_type;
287 unsigned int irq_level;
288 unsigned long irq_flags;
289
290 unsigned char __iomem * reg_addr; /* memory mapped registers address */
291 u32 phys_reg_addr;
292 bool reg_addr_requested;
293
294 MGSL_PARAMS params; /* communications parameters */
295 u32 idle_mode;
296 u32 max_frame_size; /* as set by device config */
297
298 unsigned int rbuf_fill_level;
299 unsigned int rx_pio;
300 unsigned int if_mode;
301 unsigned int base_clock;
302 unsigned int xsync;
303 unsigned int xctrl;
304
305 /* device status */
306
307 bool rx_enabled;
308 bool rx_restart;
309
310 bool tx_enabled;
311 bool tx_active;
312
313 unsigned char signals; /* serial signal states */
314 int init_error; /* initialization error */
315
316 unsigned char *tx_buf;
317 int tx_count;
318
319 char *flag_buf;
320 bool drop_rts_on_tx_done;
321 struct _input_signal_events input_signal_events;
322
323 int dcd_chkcount; /* check counts to prevent */
324 int cts_chkcount; /* too many IRQs if a signal */
325 int dsr_chkcount; /* is floating */
326 int ri_chkcount;
327
328 char *bufs; /* virtual address of DMA buffer lists */
329 dma_addr_t bufs_dma_addr; /* physical address of buffer descriptors */
330
331 unsigned int rbuf_count;
332 struct slgt_desc *rbufs;
333 unsigned int rbuf_current;
334 unsigned int rbuf_index;
335 unsigned int rbuf_fill_index;
336 unsigned short rbuf_fill_count;
337
338 unsigned int tbuf_count;
339 struct slgt_desc *tbufs;
340 unsigned int tbuf_current;
341 unsigned int tbuf_start;
342
343 unsigned char *tmp_rbuf;
344 unsigned int tmp_rbuf_count;
345
346 /* SPPP/Cisco HDLC device parts */
347
348 int netcount;
349 spinlock_t netlock;
350 #if SYNCLINK_GENERIC_HDLC
351 struct net_device *netdev;
352 #endif
353
354 };
355
356 static MGSL_PARAMS default_params = {
357 .mode = MGSL_MODE_HDLC,
358 .loopback = 0,
359 .flags = HDLC_FLAG_UNDERRUN_ABORT15,
360 .encoding = HDLC_ENCODING_NRZI_SPACE,
361 .clock_speed = 0,
362 .addr_filter = 0xff,
363 .crc_type = HDLC_CRC_16_CCITT,
364 .preamble_length = HDLC_PREAMBLE_LENGTH_8BITS,
365 .preamble = HDLC_PREAMBLE_PATTERN_NONE,
366 .data_rate = 9600,
367 .data_bits = 8,
368 .stop_bits = 1,
369 .parity = ASYNC_PARITY_NONE
370 };
371
372
373 #define BH_RECEIVE 1
374 #define BH_TRANSMIT 2
375 #define BH_STATUS 4
376 #define IO_PIN_SHUTDOWN_LIMIT 100
377
378 #define DMABUFSIZE 256
379 #define DESC_LIST_SIZE 4096
380
381 #define MASK_PARITY BIT1
382 #define MASK_FRAMING BIT0
383 #define MASK_BREAK BIT14
384 #define MASK_OVERRUN BIT4
385
386 #define GSR 0x00 /* global status */
387 #define JCR 0x04 /* JTAG control */
388 #define IODR 0x08 /* GPIO direction */
389 #define IOER 0x0c /* GPIO interrupt enable */
390 #define IOVR 0x10 /* GPIO value */
391 #define IOSR 0x14 /* GPIO interrupt status */
392 #define TDR 0x80 /* tx data */
393 #define RDR 0x80 /* rx data */
394 #define TCR 0x82 /* tx control */
395 #define TIR 0x84 /* tx idle */
396 #define TPR 0x85 /* tx preamble */
397 #define RCR 0x86 /* rx control */
398 #define VCR 0x88 /* V.24 control */
399 #define CCR 0x89 /* clock control */
400 #define BDR 0x8a /* baud divisor */
401 #define SCR 0x8c /* serial control */
402 #define SSR 0x8e /* serial status */
403 #define RDCSR 0x90 /* rx DMA control/status */
404 #define TDCSR 0x94 /* tx DMA control/status */
405 #define RDDAR 0x98 /* rx DMA descriptor address */
406 #define TDDAR 0x9c /* tx DMA descriptor address */
407 #define XSR 0x40 /* extended sync pattern */
408 #define XCR 0x44 /* extended control */
409
410 #define RXIDLE BIT14
411 #define RXBREAK BIT14
412 #define IRQ_TXDATA BIT13
413 #define IRQ_TXIDLE BIT12
414 #define IRQ_TXUNDER BIT11 /* HDLC */
415 #define IRQ_RXDATA BIT10
416 #define IRQ_RXIDLE BIT9 /* HDLC */
417 #define IRQ_RXBREAK BIT9 /* async */
418 #define IRQ_RXOVER BIT8
419 #define IRQ_DSR BIT7
420 #define IRQ_CTS BIT6
421 #define IRQ_DCD BIT5
422 #define IRQ_RI BIT4
423 #define IRQ_ALL 0x3ff0
424 #define IRQ_MASTER BIT0
425
426 #define slgt_irq_on(info, mask) \
427 wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) | (mask)))
428 #define slgt_irq_off(info, mask) \
429 wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) & ~(mask)))
430
431 static __u8 rd_reg8(struct slgt_info *info, unsigned int addr);
432 static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value);
433 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr);
434 static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value);
435 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr);
436 static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value);
437
438 static void msc_set_vcr(struct slgt_info *info);
439
440 static int startup(struct slgt_info *info);
441 static int block_til_ready(struct tty_struct *tty, struct file * filp,struct slgt_info *info);
442 static void shutdown(struct slgt_info *info);
443 static void program_hw(struct slgt_info *info);
444 static void change_params(struct slgt_info *info);
445
446 static int register_test(struct slgt_info *info);
447 static int irq_test(struct slgt_info *info);
448 static int loopback_test(struct slgt_info *info);
449 static int adapter_test(struct slgt_info *info);
450
451 static void reset_adapter(struct slgt_info *info);
452 static void reset_port(struct slgt_info *info);
453 static void async_mode(struct slgt_info *info);
454 static void sync_mode(struct slgt_info *info);
455
456 static void rx_stop(struct slgt_info *info);
457 static void rx_start(struct slgt_info *info);
458 static void reset_rbufs(struct slgt_info *info);
459 static void free_rbufs(struct slgt_info *info, unsigned int first, unsigned int last);
460 static void rdma_reset(struct slgt_info *info);
461 static bool rx_get_frame(struct slgt_info *info);
462 static bool rx_get_buf(struct slgt_info *info);
463
464 static void tx_start(struct slgt_info *info);
465 static void tx_stop(struct slgt_info *info);
466 static void tx_set_idle(struct slgt_info *info);
467 static unsigned int free_tbuf_count(struct slgt_info *info);
468 static unsigned int tbuf_bytes(struct slgt_info *info);
469 static void reset_tbufs(struct slgt_info *info);
470 static void tdma_reset(struct slgt_info *info);
471 static bool tx_load(struct slgt_info *info, const char *buf, unsigned int count);
472
473 static void get_signals(struct slgt_info *info);
474 static void set_signals(struct slgt_info *info);
475 static void enable_loopback(struct slgt_info *info);
476 static void set_rate(struct slgt_info *info, u32 data_rate);
477
478 static int bh_action(struct slgt_info *info);
479 static void bh_handler(struct work_struct *work);
480 static void bh_transmit(struct slgt_info *info);
481 static void isr_serial(struct slgt_info *info);
482 static void isr_rdma(struct slgt_info *info);
483 static void isr_txeom(struct slgt_info *info, unsigned short status);
484 static void isr_tdma(struct slgt_info *info);
485
486 static int alloc_dma_bufs(struct slgt_info *info);
487 static void free_dma_bufs(struct slgt_info *info);
488 static int alloc_desc(struct slgt_info *info);
489 static void free_desc(struct slgt_info *info);
490 static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
491 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
492
493 static int alloc_tmp_rbuf(struct slgt_info *info);
494 static void free_tmp_rbuf(struct slgt_info *info);
495
496 static void tx_timeout(struct timer_list *t);
497 static void rx_timeout(struct timer_list *t);
498
499 /*
500 * ioctl handlers
501 */
502 static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount);
503 static int get_params(struct slgt_info *info, MGSL_PARAMS __user *params);
504 static int set_params(struct slgt_info *info, MGSL_PARAMS __user *params);
505 static int get_txidle(struct slgt_info *info, int __user *idle_mode);
506 static int set_txidle(struct slgt_info *info, int idle_mode);
507 static int tx_enable(struct slgt_info *info, int enable);
508 static int tx_abort(struct slgt_info *info);
509 static int rx_enable(struct slgt_info *info, int enable);
510 static int modem_input_wait(struct slgt_info *info,int arg);
511 static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr);
512 static int tiocmget(struct tty_struct *tty);
513 static int tiocmset(struct tty_struct *tty,
514 unsigned int set, unsigned int clear);
515 static int set_break(struct tty_struct *tty, int break_state);
516 static int get_interface(struct slgt_info *info, int __user *if_mode);
517 static int set_interface(struct slgt_info *info, int if_mode);
518 static int set_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
519 static int get_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
520 static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
521 static int get_xsync(struct slgt_info *info, int __user *if_mode);
522 static int set_xsync(struct slgt_info *info, int if_mode);
523 static int get_xctrl(struct slgt_info *info, int __user *if_mode);
524 static int set_xctrl(struct slgt_info *info, int if_mode);
525
526 /*
527 * driver functions
528 */
529 static void add_device(struct slgt_info *info);
530 static void device_init(int adapter_num, struct pci_dev *pdev);
531 static int claim_resources(struct slgt_info *info);
532 static void release_resources(struct slgt_info *info);
533
534 /*
535 * DEBUG OUTPUT CODE
536 */
537 #ifndef DBGINFO
538 #define DBGINFO(fmt)
539 #endif
540 #ifndef DBGERR
541 #define DBGERR(fmt)
542 #endif
543 #ifndef DBGBH
544 #define DBGBH(fmt)
545 #endif
546 #ifndef DBGISR
547 #define DBGISR(fmt)
548 #endif
549
550 #ifdef DBGDATA
trace_block(struct slgt_info * info,const char * data,int count,const char * label)551 static void trace_block(struct slgt_info *info, const char *data, int count, const char *label)
552 {
553 int i;
554 int linecount;
555 printk("%s %s data:\n",info->device_name, label);
556 while(count) {
557 linecount = (count > 16) ? 16 : count;
558 for(i=0; i < linecount; i++)
559 printk("%02X ",(unsigned char)data[i]);
560 for(;i<17;i++)
561 printk(" ");
562 for(i=0;i<linecount;i++) {
563 if (data[i]>=040 && data[i]<=0176)
564 printk("%c",data[i]);
565 else
566 printk(".");
567 }
568 printk("\n");
569 data += linecount;
570 count -= linecount;
571 }
572 }
573 #else
574 #define DBGDATA(info, buf, size, label)
575 #endif
576
577 #ifdef DBGTBUF
dump_tbufs(struct slgt_info * info)578 static void dump_tbufs(struct slgt_info *info)
579 {
580 int i;
581 printk("tbuf_current=%d\n", info->tbuf_current);
582 for (i=0 ; i < info->tbuf_count ; i++) {
583 printk("%d: count=%04X status=%04X\n",
584 i, le16_to_cpu(info->tbufs[i].count), le16_to_cpu(info->tbufs[i].status));
585 }
586 }
587 #else
588 #define DBGTBUF(info)
589 #endif
590
591 #ifdef DBGRBUF
dump_rbufs(struct slgt_info * info)592 static void dump_rbufs(struct slgt_info *info)
593 {
594 int i;
595 printk("rbuf_current=%d\n", info->rbuf_current);
596 for (i=0 ; i < info->rbuf_count ; i++) {
597 printk("%d: count=%04X status=%04X\n",
598 i, le16_to_cpu(info->rbufs[i].count), le16_to_cpu(info->rbufs[i].status));
599 }
600 }
601 #else
602 #define DBGRBUF(info)
603 #endif
604
sanity_check(struct slgt_info * info,char * devname,const char * name)605 static inline int sanity_check(struct slgt_info *info, char *devname, const char *name)
606 {
607 #ifdef SANITY_CHECK
608 if (!info) {
609 printk("null struct slgt_info for (%s) in %s\n", devname, name);
610 return 1;
611 }
612 if (info->magic != MGSL_MAGIC) {
613 printk("bad magic number struct slgt_info (%s) in %s\n", devname, name);
614 return 1;
615 }
616 #else
617 if (!info)
618 return 1;
619 #endif
620 return 0;
621 }
622
623 /**
624 * line discipline callback wrappers
625 *
626 * The wrappers maintain line discipline references
627 * while calling into the line discipline.
628 *
629 * ldisc_receive_buf - pass receive data to line discipline
630 */
ldisc_receive_buf(struct tty_struct * tty,const __u8 * data,char * flags,int count)631 static void ldisc_receive_buf(struct tty_struct *tty,
632 const __u8 *data, char *flags, int count)
633 {
634 struct tty_ldisc *ld;
635 if (!tty)
636 return;
637 ld = tty_ldisc_ref(tty);
638 if (ld) {
639 if (ld->ops->receive_buf)
640 ld->ops->receive_buf(tty, data, flags, count);
641 tty_ldisc_deref(ld);
642 }
643 }
644
645 /* tty callbacks */
646
open(struct tty_struct * tty,struct file * filp)647 static int open(struct tty_struct *tty, struct file *filp)
648 {
649 struct slgt_info *info;
650 int retval, line;
651 unsigned long flags;
652
653 line = tty->index;
654 if (line >= slgt_device_count) {
655 DBGERR(("%s: open with invalid line #%d.\n", driver_name, line));
656 return -ENODEV;
657 }
658
659 info = slgt_device_list;
660 while(info && info->line != line)
661 info = info->next_device;
662 if (sanity_check(info, tty->name, "open"))
663 return -ENODEV;
664 if (info->init_error) {
665 DBGERR(("%s init error=%d\n", info->device_name, info->init_error));
666 return -ENODEV;
667 }
668
669 tty->driver_data = info;
670 info->port.tty = tty;
671
672 DBGINFO(("%s open, old ref count = %d\n", info->device_name, info->port.count));
673
674 mutex_lock(&info->port.mutex);
675 info->port.low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
676
677 spin_lock_irqsave(&info->netlock, flags);
678 if (info->netcount) {
679 retval = -EBUSY;
680 spin_unlock_irqrestore(&info->netlock, flags);
681 mutex_unlock(&info->port.mutex);
682 goto cleanup;
683 }
684 info->port.count++;
685 spin_unlock_irqrestore(&info->netlock, flags);
686
687 if (info->port.count == 1) {
688 /* 1st open on this device, init hardware */
689 retval = startup(info);
690 if (retval < 0) {
691 mutex_unlock(&info->port.mutex);
692 goto cleanup;
693 }
694 }
695 mutex_unlock(&info->port.mutex);
696 retval = block_til_ready(tty, filp, info);
697 if (retval) {
698 DBGINFO(("%s block_til_ready rc=%d\n", info->device_name, retval));
699 goto cleanup;
700 }
701
702 retval = 0;
703
704 cleanup:
705 if (retval) {
706 if (tty->count == 1)
707 info->port.tty = NULL; /* tty layer will release tty struct */
708 if(info->port.count)
709 info->port.count--;
710 }
711
712 DBGINFO(("%s open rc=%d\n", info->device_name, retval));
713 return retval;
714 }
715
close(struct tty_struct * tty,struct file * filp)716 static void close(struct tty_struct *tty, struct file *filp)
717 {
718 struct slgt_info *info = tty->driver_data;
719
720 if (sanity_check(info, tty->name, "close"))
721 return;
722 DBGINFO(("%s close entry, count=%d\n", info->device_name, info->port.count));
723
724 if (tty_port_close_start(&info->port, tty, filp) == 0)
725 goto cleanup;
726
727 mutex_lock(&info->port.mutex);
728 if (tty_port_initialized(&info->port))
729 wait_until_sent(tty, info->timeout);
730 flush_buffer(tty);
731 tty_ldisc_flush(tty);
732
733 shutdown(info);
734 mutex_unlock(&info->port.mutex);
735
736 tty_port_close_end(&info->port, tty);
737 info->port.tty = NULL;
738 cleanup:
739 DBGINFO(("%s close exit, count=%d\n", tty->driver->name, info->port.count));
740 }
741
hangup(struct tty_struct * tty)742 static void hangup(struct tty_struct *tty)
743 {
744 struct slgt_info *info = tty->driver_data;
745 unsigned long flags;
746
747 if (sanity_check(info, tty->name, "hangup"))
748 return;
749 DBGINFO(("%s hangup\n", info->device_name));
750
751 flush_buffer(tty);
752
753 mutex_lock(&info->port.mutex);
754 shutdown(info);
755
756 spin_lock_irqsave(&info->port.lock, flags);
757 info->port.count = 0;
758 info->port.tty = NULL;
759 spin_unlock_irqrestore(&info->port.lock, flags);
760 tty_port_set_active(&info->port, 0);
761 mutex_unlock(&info->port.mutex);
762
763 wake_up_interruptible(&info->port.open_wait);
764 }
765
set_termios(struct tty_struct * tty,struct ktermios * old_termios)766 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios)
767 {
768 struct slgt_info *info = tty->driver_data;
769 unsigned long flags;
770
771 DBGINFO(("%s set_termios\n", tty->driver->name));
772
773 change_params(info);
774
775 /* Handle transition to B0 status */
776 if ((old_termios->c_cflag & CBAUD) && !C_BAUD(tty)) {
777 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
778 spin_lock_irqsave(&info->lock,flags);
779 set_signals(info);
780 spin_unlock_irqrestore(&info->lock,flags);
781 }
782
783 /* Handle transition away from B0 status */
784 if (!(old_termios->c_cflag & CBAUD) && C_BAUD(tty)) {
785 info->signals |= SerialSignal_DTR;
786 if (!C_CRTSCTS(tty) || !tty_throttled(tty))
787 info->signals |= SerialSignal_RTS;
788 spin_lock_irqsave(&info->lock,flags);
789 set_signals(info);
790 spin_unlock_irqrestore(&info->lock,flags);
791 }
792
793 /* Handle turning off CRTSCTS */
794 if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty)) {
795 tty->hw_stopped = 0;
796 tx_release(tty);
797 }
798 }
799
update_tx_timer(struct slgt_info * info)800 static void update_tx_timer(struct slgt_info *info)
801 {
802 /*
803 * use worst case speed of 1200bps to calculate transmit timeout
804 * based on data in buffers (tbuf_bytes) and FIFO (128 bytes)
805 */
806 if (info->params.mode == MGSL_MODE_HDLC) {
807 int timeout = (tbuf_bytes(info) * 7) + 1000;
808 mod_timer(&info->tx_timer, jiffies + msecs_to_jiffies(timeout));
809 }
810 }
811
write(struct tty_struct * tty,const unsigned char * buf,int count)812 static int write(struct tty_struct *tty,
813 const unsigned char *buf, int count)
814 {
815 int ret = 0;
816 struct slgt_info *info = tty->driver_data;
817 unsigned long flags;
818
819 if (sanity_check(info, tty->name, "write"))
820 return -EIO;
821
822 DBGINFO(("%s write count=%d\n", info->device_name, count));
823
824 if (!info->tx_buf || (count > info->max_frame_size))
825 return -EIO;
826
827 if (!count || tty->stopped || tty->hw_stopped)
828 return 0;
829
830 spin_lock_irqsave(&info->lock, flags);
831
832 if (info->tx_count) {
833 /* send accumulated data from send_char() */
834 if (!tx_load(info, info->tx_buf, info->tx_count))
835 goto cleanup;
836 info->tx_count = 0;
837 }
838
839 if (tx_load(info, buf, count))
840 ret = count;
841
842 cleanup:
843 spin_unlock_irqrestore(&info->lock, flags);
844 DBGINFO(("%s write rc=%d\n", info->device_name, ret));
845 return ret;
846 }
847
put_char(struct tty_struct * tty,unsigned char ch)848 static int put_char(struct tty_struct *tty, unsigned char ch)
849 {
850 struct slgt_info *info = tty->driver_data;
851 unsigned long flags;
852 int ret = 0;
853
854 if (sanity_check(info, tty->name, "put_char"))
855 return 0;
856 DBGINFO(("%s put_char(%d)\n", info->device_name, ch));
857 if (!info->tx_buf)
858 return 0;
859 spin_lock_irqsave(&info->lock,flags);
860 if (info->tx_count < info->max_frame_size) {
861 info->tx_buf[info->tx_count++] = ch;
862 ret = 1;
863 }
864 spin_unlock_irqrestore(&info->lock,flags);
865 return ret;
866 }
867
send_xchar(struct tty_struct * tty,char ch)868 static void send_xchar(struct tty_struct *tty, char ch)
869 {
870 struct slgt_info *info = tty->driver_data;
871 unsigned long flags;
872
873 if (sanity_check(info, tty->name, "send_xchar"))
874 return;
875 DBGINFO(("%s send_xchar(%d)\n", info->device_name, ch));
876 info->x_char = ch;
877 if (ch) {
878 spin_lock_irqsave(&info->lock,flags);
879 if (!info->tx_enabled)
880 tx_start(info);
881 spin_unlock_irqrestore(&info->lock,flags);
882 }
883 }
884
wait_until_sent(struct tty_struct * tty,int timeout)885 static void wait_until_sent(struct tty_struct *tty, int timeout)
886 {
887 struct slgt_info *info = tty->driver_data;
888 unsigned long orig_jiffies, char_time;
889
890 if (!info )
891 return;
892 if (sanity_check(info, tty->name, "wait_until_sent"))
893 return;
894 DBGINFO(("%s wait_until_sent entry\n", info->device_name));
895 if (!tty_port_initialized(&info->port))
896 goto exit;
897
898 orig_jiffies = jiffies;
899
900 /* Set check interval to 1/5 of estimated time to
901 * send a character, and make it at least 1. The check
902 * interval should also be less than the timeout.
903 * Note: use tight timings here to satisfy the NIST-PCTS.
904 */
905
906 if (info->params.data_rate) {
907 char_time = info->timeout/(32 * 5);
908 if (!char_time)
909 char_time++;
910 } else
911 char_time = 1;
912
913 if (timeout)
914 char_time = min_t(unsigned long, char_time, timeout);
915
916 while (info->tx_active) {
917 msleep_interruptible(jiffies_to_msecs(char_time));
918 if (signal_pending(current))
919 break;
920 if (timeout && time_after(jiffies, orig_jiffies + timeout))
921 break;
922 }
923 exit:
924 DBGINFO(("%s wait_until_sent exit\n", info->device_name));
925 }
926
write_room(struct tty_struct * tty)927 static int write_room(struct tty_struct *tty)
928 {
929 struct slgt_info *info = tty->driver_data;
930 int ret;
931
932 if (sanity_check(info, tty->name, "write_room"))
933 return 0;
934 ret = (info->tx_active) ? 0 : HDLC_MAX_FRAME_SIZE;
935 DBGINFO(("%s write_room=%d\n", info->device_name, ret));
936 return ret;
937 }
938
flush_chars(struct tty_struct * tty)939 static void flush_chars(struct tty_struct *tty)
940 {
941 struct slgt_info *info = tty->driver_data;
942 unsigned long flags;
943
944 if (sanity_check(info, tty->name, "flush_chars"))
945 return;
946 DBGINFO(("%s flush_chars entry tx_count=%d\n", info->device_name, info->tx_count));
947
948 if (info->tx_count <= 0 || tty->stopped ||
949 tty->hw_stopped || !info->tx_buf)
950 return;
951
952 DBGINFO(("%s flush_chars start transmit\n", info->device_name));
953
954 spin_lock_irqsave(&info->lock,flags);
955 if (info->tx_count && tx_load(info, info->tx_buf, info->tx_count))
956 info->tx_count = 0;
957 spin_unlock_irqrestore(&info->lock,flags);
958 }
959
flush_buffer(struct tty_struct * tty)960 static void flush_buffer(struct tty_struct *tty)
961 {
962 struct slgt_info *info = tty->driver_data;
963 unsigned long flags;
964
965 if (sanity_check(info, tty->name, "flush_buffer"))
966 return;
967 DBGINFO(("%s flush_buffer\n", info->device_name));
968
969 spin_lock_irqsave(&info->lock, flags);
970 info->tx_count = 0;
971 spin_unlock_irqrestore(&info->lock, flags);
972
973 tty_wakeup(tty);
974 }
975
976 /*
977 * throttle (stop) transmitter
978 */
tx_hold(struct tty_struct * tty)979 static void tx_hold(struct tty_struct *tty)
980 {
981 struct slgt_info *info = tty->driver_data;
982 unsigned long flags;
983
984 if (sanity_check(info, tty->name, "tx_hold"))
985 return;
986 DBGINFO(("%s tx_hold\n", info->device_name));
987 spin_lock_irqsave(&info->lock,flags);
988 if (info->tx_enabled && info->params.mode == MGSL_MODE_ASYNC)
989 tx_stop(info);
990 spin_unlock_irqrestore(&info->lock,flags);
991 }
992
993 /*
994 * release (start) transmitter
995 */
tx_release(struct tty_struct * tty)996 static void tx_release(struct tty_struct *tty)
997 {
998 struct slgt_info *info = tty->driver_data;
999 unsigned long flags;
1000
1001 if (sanity_check(info, tty->name, "tx_release"))
1002 return;
1003 DBGINFO(("%s tx_release\n", info->device_name));
1004 spin_lock_irqsave(&info->lock, flags);
1005 if (info->tx_count && tx_load(info, info->tx_buf, info->tx_count))
1006 info->tx_count = 0;
1007 spin_unlock_irqrestore(&info->lock, flags);
1008 }
1009
1010 /*
1011 * Service an IOCTL request
1012 *
1013 * Arguments
1014 *
1015 * tty pointer to tty instance data
1016 * cmd IOCTL command code
1017 * arg command argument/context
1018 *
1019 * Return 0 if success, otherwise error code
1020 */
ioctl(struct tty_struct * tty,unsigned int cmd,unsigned long arg)1021 static int ioctl(struct tty_struct *tty,
1022 unsigned int cmd, unsigned long arg)
1023 {
1024 struct slgt_info *info = tty->driver_data;
1025 void __user *argp = (void __user *)arg;
1026 int ret;
1027
1028 if (sanity_check(info, tty->name, "ioctl"))
1029 return -ENODEV;
1030 DBGINFO(("%s ioctl() cmd=%08X\n", info->device_name, cmd));
1031
1032 if (cmd != TIOCMIWAIT) {
1033 if (tty_io_error(tty))
1034 return -EIO;
1035 }
1036
1037 switch (cmd) {
1038 case MGSL_IOCWAITEVENT:
1039 return wait_mgsl_event(info, argp);
1040 case TIOCMIWAIT:
1041 return modem_input_wait(info,(int)arg);
1042 case MGSL_IOCSGPIO:
1043 return set_gpio(info, argp);
1044 case MGSL_IOCGGPIO:
1045 return get_gpio(info, argp);
1046 case MGSL_IOCWAITGPIO:
1047 return wait_gpio(info, argp);
1048 case MGSL_IOCGXSYNC:
1049 return get_xsync(info, argp);
1050 case MGSL_IOCSXSYNC:
1051 return set_xsync(info, (int)arg);
1052 case MGSL_IOCGXCTRL:
1053 return get_xctrl(info, argp);
1054 case MGSL_IOCSXCTRL:
1055 return set_xctrl(info, (int)arg);
1056 }
1057 mutex_lock(&info->port.mutex);
1058 switch (cmd) {
1059 case MGSL_IOCGPARAMS:
1060 ret = get_params(info, argp);
1061 break;
1062 case MGSL_IOCSPARAMS:
1063 ret = set_params(info, argp);
1064 break;
1065 case MGSL_IOCGTXIDLE:
1066 ret = get_txidle(info, argp);
1067 break;
1068 case MGSL_IOCSTXIDLE:
1069 ret = set_txidle(info, (int)arg);
1070 break;
1071 case MGSL_IOCTXENABLE:
1072 ret = tx_enable(info, (int)arg);
1073 break;
1074 case MGSL_IOCRXENABLE:
1075 ret = rx_enable(info, (int)arg);
1076 break;
1077 case MGSL_IOCTXABORT:
1078 ret = tx_abort(info);
1079 break;
1080 case MGSL_IOCGSTATS:
1081 ret = get_stats(info, argp);
1082 break;
1083 case MGSL_IOCGIF:
1084 ret = get_interface(info, argp);
1085 break;
1086 case MGSL_IOCSIF:
1087 ret = set_interface(info,(int)arg);
1088 break;
1089 default:
1090 ret = -ENOIOCTLCMD;
1091 }
1092 mutex_unlock(&info->port.mutex);
1093 return ret;
1094 }
1095
get_icount(struct tty_struct * tty,struct serial_icounter_struct * icount)1096 static int get_icount(struct tty_struct *tty,
1097 struct serial_icounter_struct *icount)
1098
1099 {
1100 struct slgt_info *info = tty->driver_data;
1101 struct mgsl_icount cnow; /* kernel counter temps */
1102 unsigned long flags;
1103
1104 spin_lock_irqsave(&info->lock,flags);
1105 cnow = info->icount;
1106 spin_unlock_irqrestore(&info->lock,flags);
1107
1108 icount->cts = cnow.cts;
1109 icount->dsr = cnow.dsr;
1110 icount->rng = cnow.rng;
1111 icount->dcd = cnow.dcd;
1112 icount->rx = cnow.rx;
1113 icount->tx = cnow.tx;
1114 icount->frame = cnow.frame;
1115 icount->overrun = cnow.overrun;
1116 icount->parity = cnow.parity;
1117 icount->brk = cnow.brk;
1118 icount->buf_overrun = cnow.buf_overrun;
1119
1120 return 0;
1121 }
1122
1123 /*
1124 * support for 32 bit ioctl calls on 64 bit systems
1125 */
1126 #ifdef CONFIG_COMPAT
get_params32(struct slgt_info * info,struct MGSL_PARAMS32 __user * user_params)1127 static long get_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *user_params)
1128 {
1129 struct MGSL_PARAMS32 tmp_params;
1130
1131 DBGINFO(("%s get_params32\n", info->device_name));
1132 memset(&tmp_params, 0, sizeof(tmp_params));
1133 tmp_params.mode = (compat_ulong_t)info->params.mode;
1134 tmp_params.loopback = info->params.loopback;
1135 tmp_params.flags = info->params.flags;
1136 tmp_params.encoding = info->params.encoding;
1137 tmp_params.clock_speed = (compat_ulong_t)info->params.clock_speed;
1138 tmp_params.addr_filter = info->params.addr_filter;
1139 tmp_params.crc_type = info->params.crc_type;
1140 tmp_params.preamble_length = info->params.preamble_length;
1141 tmp_params.preamble = info->params.preamble;
1142 tmp_params.data_rate = (compat_ulong_t)info->params.data_rate;
1143 tmp_params.data_bits = info->params.data_bits;
1144 tmp_params.stop_bits = info->params.stop_bits;
1145 tmp_params.parity = info->params.parity;
1146 if (copy_to_user(user_params, &tmp_params, sizeof(struct MGSL_PARAMS32)))
1147 return -EFAULT;
1148 return 0;
1149 }
1150
set_params32(struct slgt_info * info,struct MGSL_PARAMS32 __user * new_params)1151 static long set_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *new_params)
1152 {
1153 struct MGSL_PARAMS32 tmp_params;
1154
1155 DBGINFO(("%s set_params32\n", info->device_name));
1156 if (copy_from_user(&tmp_params, new_params, sizeof(struct MGSL_PARAMS32)))
1157 return -EFAULT;
1158
1159 spin_lock(&info->lock);
1160 if (tmp_params.mode == MGSL_MODE_BASE_CLOCK) {
1161 info->base_clock = tmp_params.clock_speed;
1162 } else {
1163 info->params.mode = tmp_params.mode;
1164 info->params.loopback = tmp_params.loopback;
1165 info->params.flags = tmp_params.flags;
1166 info->params.encoding = tmp_params.encoding;
1167 info->params.clock_speed = tmp_params.clock_speed;
1168 info->params.addr_filter = tmp_params.addr_filter;
1169 info->params.crc_type = tmp_params.crc_type;
1170 info->params.preamble_length = tmp_params.preamble_length;
1171 info->params.preamble = tmp_params.preamble;
1172 info->params.data_rate = tmp_params.data_rate;
1173 info->params.data_bits = tmp_params.data_bits;
1174 info->params.stop_bits = tmp_params.stop_bits;
1175 info->params.parity = tmp_params.parity;
1176 }
1177 spin_unlock(&info->lock);
1178
1179 program_hw(info);
1180
1181 return 0;
1182 }
1183
slgt_compat_ioctl(struct tty_struct * tty,unsigned int cmd,unsigned long arg)1184 static long slgt_compat_ioctl(struct tty_struct *tty,
1185 unsigned int cmd, unsigned long arg)
1186 {
1187 struct slgt_info *info = tty->driver_data;
1188 int rc;
1189
1190 if (sanity_check(info, tty->name, "compat_ioctl"))
1191 return -ENODEV;
1192 DBGINFO(("%s compat_ioctl() cmd=%08X\n", info->device_name, cmd));
1193
1194 switch (cmd) {
1195 case MGSL_IOCSPARAMS32:
1196 rc = set_params32(info, compat_ptr(arg));
1197 break;
1198
1199 case MGSL_IOCGPARAMS32:
1200 rc = get_params32(info, compat_ptr(arg));
1201 break;
1202
1203 case MGSL_IOCGPARAMS:
1204 case MGSL_IOCSPARAMS:
1205 case MGSL_IOCGTXIDLE:
1206 case MGSL_IOCGSTATS:
1207 case MGSL_IOCWAITEVENT:
1208 case MGSL_IOCGIF:
1209 case MGSL_IOCSGPIO:
1210 case MGSL_IOCGGPIO:
1211 case MGSL_IOCWAITGPIO:
1212 case MGSL_IOCGXSYNC:
1213 case MGSL_IOCGXCTRL:
1214 rc = ioctl(tty, cmd, (unsigned long)compat_ptr(arg));
1215 break;
1216 default:
1217 rc = ioctl(tty, cmd, arg);
1218 }
1219 DBGINFO(("%s compat_ioctl() cmd=%08X rc=%d\n", info->device_name, cmd, rc));
1220 return rc;
1221 }
1222 #else
1223 #define slgt_compat_ioctl NULL
1224 #endif /* ifdef CONFIG_COMPAT */
1225
1226 /*
1227 * proc fs support
1228 */
line_info(struct seq_file * m,struct slgt_info * info)1229 static inline void line_info(struct seq_file *m, struct slgt_info *info)
1230 {
1231 char stat_buf[30];
1232 unsigned long flags;
1233
1234 seq_printf(m, "%s: IO=%08X IRQ=%d MaxFrameSize=%u\n",
1235 info->device_name, info->phys_reg_addr,
1236 info->irq_level, info->max_frame_size);
1237
1238 /* output current serial signal states */
1239 spin_lock_irqsave(&info->lock,flags);
1240 get_signals(info);
1241 spin_unlock_irqrestore(&info->lock,flags);
1242
1243 stat_buf[0] = 0;
1244 stat_buf[1] = 0;
1245 if (info->signals & SerialSignal_RTS)
1246 strcat(stat_buf, "|RTS");
1247 if (info->signals & SerialSignal_CTS)
1248 strcat(stat_buf, "|CTS");
1249 if (info->signals & SerialSignal_DTR)
1250 strcat(stat_buf, "|DTR");
1251 if (info->signals & SerialSignal_DSR)
1252 strcat(stat_buf, "|DSR");
1253 if (info->signals & SerialSignal_DCD)
1254 strcat(stat_buf, "|CD");
1255 if (info->signals & SerialSignal_RI)
1256 strcat(stat_buf, "|RI");
1257
1258 if (info->params.mode != MGSL_MODE_ASYNC) {
1259 seq_printf(m, "\tHDLC txok:%d rxok:%d",
1260 info->icount.txok, info->icount.rxok);
1261 if (info->icount.txunder)
1262 seq_printf(m, " txunder:%d", info->icount.txunder);
1263 if (info->icount.txabort)
1264 seq_printf(m, " txabort:%d", info->icount.txabort);
1265 if (info->icount.rxshort)
1266 seq_printf(m, " rxshort:%d", info->icount.rxshort);
1267 if (info->icount.rxlong)
1268 seq_printf(m, " rxlong:%d", info->icount.rxlong);
1269 if (info->icount.rxover)
1270 seq_printf(m, " rxover:%d", info->icount.rxover);
1271 if (info->icount.rxcrc)
1272 seq_printf(m, " rxcrc:%d", info->icount.rxcrc);
1273 } else {
1274 seq_printf(m, "\tASYNC tx:%d rx:%d",
1275 info->icount.tx, info->icount.rx);
1276 if (info->icount.frame)
1277 seq_printf(m, " fe:%d", info->icount.frame);
1278 if (info->icount.parity)
1279 seq_printf(m, " pe:%d", info->icount.parity);
1280 if (info->icount.brk)
1281 seq_printf(m, " brk:%d", info->icount.brk);
1282 if (info->icount.overrun)
1283 seq_printf(m, " oe:%d", info->icount.overrun);
1284 }
1285
1286 /* Append serial signal status to end */
1287 seq_printf(m, " %s\n", stat_buf+1);
1288
1289 seq_printf(m, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
1290 info->tx_active,info->bh_requested,info->bh_running,
1291 info->pending_bh);
1292 }
1293
1294 /* Called to print information about devices
1295 */
synclink_gt_proc_show(struct seq_file * m,void * v)1296 static int synclink_gt_proc_show(struct seq_file *m, void *v)
1297 {
1298 struct slgt_info *info;
1299
1300 seq_puts(m, "synclink_gt driver\n");
1301
1302 info = slgt_device_list;
1303 while( info ) {
1304 line_info(m, info);
1305 info = info->next_device;
1306 }
1307 return 0;
1308 }
1309
1310 /*
1311 * return count of bytes in transmit buffer
1312 */
chars_in_buffer(struct tty_struct * tty)1313 static int chars_in_buffer(struct tty_struct *tty)
1314 {
1315 struct slgt_info *info = tty->driver_data;
1316 int count;
1317 if (sanity_check(info, tty->name, "chars_in_buffer"))
1318 return 0;
1319 count = tbuf_bytes(info);
1320 DBGINFO(("%s chars_in_buffer()=%d\n", info->device_name, count));
1321 return count;
1322 }
1323
1324 /*
1325 * signal remote device to throttle send data (our receive data)
1326 */
throttle(struct tty_struct * tty)1327 static void throttle(struct tty_struct * tty)
1328 {
1329 struct slgt_info *info = tty->driver_data;
1330 unsigned long flags;
1331
1332 if (sanity_check(info, tty->name, "throttle"))
1333 return;
1334 DBGINFO(("%s throttle\n", info->device_name));
1335 if (I_IXOFF(tty))
1336 send_xchar(tty, STOP_CHAR(tty));
1337 if (C_CRTSCTS(tty)) {
1338 spin_lock_irqsave(&info->lock,flags);
1339 info->signals &= ~SerialSignal_RTS;
1340 set_signals(info);
1341 spin_unlock_irqrestore(&info->lock,flags);
1342 }
1343 }
1344
1345 /*
1346 * signal remote device to stop throttling send data (our receive data)
1347 */
unthrottle(struct tty_struct * tty)1348 static void unthrottle(struct tty_struct * tty)
1349 {
1350 struct slgt_info *info = tty->driver_data;
1351 unsigned long flags;
1352
1353 if (sanity_check(info, tty->name, "unthrottle"))
1354 return;
1355 DBGINFO(("%s unthrottle\n", info->device_name));
1356 if (I_IXOFF(tty)) {
1357 if (info->x_char)
1358 info->x_char = 0;
1359 else
1360 send_xchar(tty, START_CHAR(tty));
1361 }
1362 if (C_CRTSCTS(tty)) {
1363 spin_lock_irqsave(&info->lock,flags);
1364 info->signals |= SerialSignal_RTS;
1365 set_signals(info);
1366 spin_unlock_irqrestore(&info->lock,flags);
1367 }
1368 }
1369
1370 /*
1371 * set or clear transmit break condition
1372 * break_state -1=set break condition, 0=clear
1373 */
set_break(struct tty_struct * tty,int break_state)1374 static int set_break(struct tty_struct *tty, int break_state)
1375 {
1376 struct slgt_info *info = tty->driver_data;
1377 unsigned short value;
1378 unsigned long flags;
1379
1380 if (sanity_check(info, tty->name, "set_break"))
1381 return -EINVAL;
1382 DBGINFO(("%s set_break(%d)\n", info->device_name, break_state));
1383
1384 spin_lock_irqsave(&info->lock,flags);
1385 value = rd_reg16(info, TCR);
1386 if (break_state == -1)
1387 value |= BIT6;
1388 else
1389 value &= ~BIT6;
1390 wr_reg16(info, TCR, value);
1391 spin_unlock_irqrestore(&info->lock,flags);
1392 return 0;
1393 }
1394
1395 #if SYNCLINK_GENERIC_HDLC
1396
1397 /**
1398 * called by generic HDLC layer when protocol selected (PPP, frame relay, etc.)
1399 * set encoding and frame check sequence (FCS) options
1400 *
1401 * dev pointer to network device structure
1402 * encoding serial encoding setting
1403 * parity FCS setting
1404 *
1405 * returns 0 if success, otherwise error code
1406 */
hdlcdev_attach(struct net_device * dev,unsigned short encoding,unsigned short parity)1407 static int hdlcdev_attach(struct net_device *dev, unsigned short encoding,
1408 unsigned short parity)
1409 {
1410 struct slgt_info *info = dev_to_port(dev);
1411 unsigned char new_encoding;
1412 unsigned short new_crctype;
1413
1414 /* return error if TTY interface open */
1415 if (info->port.count)
1416 return -EBUSY;
1417
1418 DBGINFO(("%s hdlcdev_attach\n", info->device_name));
1419
1420 switch (encoding)
1421 {
1422 case ENCODING_NRZ: new_encoding = HDLC_ENCODING_NRZ; break;
1423 case ENCODING_NRZI: new_encoding = HDLC_ENCODING_NRZI_SPACE; break;
1424 case ENCODING_FM_MARK: new_encoding = HDLC_ENCODING_BIPHASE_MARK; break;
1425 case ENCODING_FM_SPACE: new_encoding = HDLC_ENCODING_BIPHASE_SPACE; break;
1426 case ENCODING_MANCHESTER: new_encoding = HDLC_ENCODING_BIPHASE_LEVEL; break;
1427 default: return -EINVAL;
1428 }
1429
1430 switch (parity)
1431 {
1432 case PARITY_NONE: new_crctype = HDLC_CRC_NONE; break;
1433 case PARITY_CRC16_PR1_CCITT: new_crctype = HDLC_CRC_16_CCITT; break;
1434 case PARITY_CRC32_PR1_CCITT: new_crctype = HDLC_CRC_32_CCITT; break;
1435 default: return -EINVAL;
1436 }
1437
1438 info->params.encoding = new_encoding;
1439 info->params.crc_type = new_crctype;
1440
1441 /* if network interface up, reprogram hardware */
1442 if (info->netcount)
1443 program_hw(info);
1444
1445 return 0;
1446 }
1447
1448 /**
1449 * called by generic HDLC layer to send frame
1450 *
1451 * skb socket buffer containing HDLC frame
1452 * dev pointer to network device structure
1453 */
hdlcdev_xmit(struct sk_buff * skb,struct net_device * dev)1454 static netdev_tx_t hdlcdev_xmit(struct sk_buff *skb,
1455 struct net_device *dev)
1456 {
1457 struct slgt_info *info = dev_to_port(dev);
1458 unsigned long flags;
1459
1460 DBGINFO(("%s hdlc_xmit\n", dev->name));
1461
1462 if (!skb->len)
1463 return NETDEV_TX_OK;
1464
1465 /* stop sending until this frame completes */
1466 netif_stop_queue(dev);
1467
1468 /* update network statistics */
1469 dev->stats.tx_packets++;
1470 dev->stats.tx_bytes += skb->len;
1471
1472 /* save start time for transmit timeout detection */
1473 netif_trans_update(dev);
1474
1475 spin_lock_irqsave(&info->lock, flags);
1476 tx_load(info, skb->data, skb->len);
1477 spin_unlock_irqrestore(&info->lock, flags);
1478
1479 /* done with socket buffer, so free it */
1480 dev_kfree_skb(skb);
1481
1482 return NETDEV_TX_OK;
1483 }
1484
1485 /**
1486 * called by network layer when interface enabled
1487 * claim resources and initialize hardware
1488 *
1489 * dev pointer to network device structure
1490 *
1491 * returns 0 if success, otherwise error code
1492 */
hdlcdev_open(struct net_device * dev)1493 static int hdlcdev_open(struct net_device *dev)
1494 {
1495 struct slgt_info *info = dev_to_port(dev);
1496 int rc;
1497 unsigned long flags;
1498
1499 if (!try_module_get(THIS_MODULE))
1500 return -EBUSY;
1501
1502 DBGINFO(("%s hdlcdev_open\n", dev->name));
1503
1504 /* generic HDLC layer open processing */
1505 rc = hdlc_open(dev);
1506 if (rc)
1507 return rc;
1508
1509 /* arbitrate between network and tty opens */
1510 spin_lock_irqsave(&info->netlock, flags);
1511 if (info->port.count != 0 || info->netcount != 0) {
1512 DBGINFO(("%s hdlc_open busy\n", dev->name));
1513 spin_unlock_irqrestore(&info->netlock, flags);
1514 return -EBUSY;
1515 }
1516 info->netcount=1;
1517 spin_unlock_irqrestore(&info->netlock, flags);
1518
1519 /* claim resources and init adapter */
1520 if ((rc = startup(info)) != 0) {
1521 spin_lock_irqsave(&info->netlock, flags);
1522 info->netcount=0;
1523 spin_unlock_irqrestore(&info->netlock, flags);
1524 return rc;
1525 }
1526
1527 /* assert RTS and DTR, apply hardware settings */
1528 info->signals |= SerialSignal_RTS | SerialSignal_DTR;
1529 program_hw(info);
1530
1531 /* enable network layer transmit */
1532 netif_trans_update(dev);
1533 netif_start_queue(dev);
1534
1535 /* inform generic HDLC layer of current DCD status */
1536 spin_lock_irqsave(&info->lock, flags);
1537 get_signals(info);
1538 spin_unlock_irqrestore(&info->lock, flags);
1539 if (info->signals & SerialSignal_DCD)
1540 netif_carrier_on(dev);
1541 else
1542 netif_carrier_off(dev);
1543 return 0;
1544 }
1545
1546 /**
1547 * called by network layer when interface is disabled
1548 * shutdown hardware and release resources
1549 *
1550 * dev pointer to network device structure
1551 *
1552 * returns 0 if success, otherwise error code
1553 */
hdlcdev_close(struct net_device * dev)1554 static int hdlcdev_close(struct net_device *dev)
1555 {
1556 struct slgt_info *info = dev_to_port(dev);
1557 unsigned long flags;
1558
1559 DBGINFO(("%s hdlcdev_close\n", dev->name));
1560
1561 netif_stop_queue(dev);
1562
1563 /* shutdown adapter and release resources */
1564 shutdown(info);
1565
1566 hdlc_close(dev);
1567
1568 spin_lock_irqsave(&info->netlock, flags);
1569 info->netcount=0;
1570 spin_unlock_irqrestore(&info->netlock, flags);
1571
1572 module_put(THIS_MODULE);
1573 return 0;
1574 }
1575
1576 /**
1577 * called by network layer to process IOCTL call to network device
1578 *
1579 * dev pointer to network device structure
1580 * ifr pointer to network interface request structure
1581 * cmd IOCTL command code
1582 *
1583 * returns 0 if success, otherwise error code
1584 */
hdlcdev_ioctl(struct net_device * dev,struct ifreq * ifr,int cmd)1585 static int hdlcdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
1586 {
1587 const size_t size = sizeof(sync_serial_settings);
1588 sync_serial_settings new_line;
1589 sync_serial_settings __user *line = ifr->ifr_settings.ifs_ifsu.sync;
1590 struct slgt_info *info = dev_to_port(dev);
1591 unsigned int flags;
1592
1593 DBGINFO(("%s hdlcdev_ioctl\n", dev->name));
1594
1595 /* return error if TTY interface open */
1596 if (info->port.count)
1597 return -EBUSY;
1598
1599 if (cmd != SIOCWANDEV)
1600 return hdlc_ioctl(dev, ifr, cmd);
1601
1602 memset(&new_line, 0, sizeof(new_line));
1603
1604 switch(ifr->ifr_settings.type) {
1605 case IF_GET_IFACE: /* return current sync_serial_settings */
1606
1607 ifr->ifr_settings.type = IF_IFACE_SYNC_SERIAL;
1608 if (ifr->ifr_settings.size < size) {
1609 ifr->ifr_settings.size = size; /* data size wanted */
1610 return -ENOBUFS;
1611 }
1612
1613 flags = info->params.flags & (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1614 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN |
1615 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1616 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN);
1617
1618 switch (flags){
1619 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN): new_line.clock_type = CLOCK_EXT; break;
1620 case (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG): new_line.clock_type = CLOCK_INT; break;
1621 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG): new_line.clock_type = CLOCK_TXINT; break;
1622 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN): new_line.clock_type = CLOCK_TXFROMRX; break;
1623 default: new_line.clock_type = CLOCK_DEFAULT;
1624 }
1625
1626 new_line.clock_rate = info->params.clock_speed;
1627 new_line.loopback = info->params.loopback ? 1:0;
1628
1629 if (copy_to_user(line, &new_line, size))
1630 return -EFAULT;
1631 return 0;
1632
1633 case IF_IFACE_SYNC_SERIAL: /* set sync_serial_settings */
1634
1635 if(!capable(CAP_NET_ADMIN))
1636 return -EPERM;
1637 if (copy_from_user(&new_line, line, size))
1638 return -EFAULT;
1639
1640 switch (new_line.clock_type)
1641 {
1642 case CLOCK_EXT: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN; break;
1643 case CLOCK_TXFROMRX: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN; break;
1644 case CLOCK_INT: flags = HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG; break;
1645 case CLOCK_TXINT: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG; break;
1646 case CLOCK_DEFAULT: flags = info->params.flags &
1647 (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1648 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN |
1649 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1650 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN); break;
1651 default: return -EINVAL;
1652 }
1653
1654 if (new_line.loopback != 0 && new_line.loopback != 1)
1655 return -EINVAL;
1656
1657 info->params.flags &= ~(HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1658 HDLC_FLAG_RXC_BRG | HDLC_FLAG_RXC_TXCPIN |
1659 HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1660 HDLC_FLAG_TXC_BRG | HDLC_FLAG_TXC_RXCPIN);
1661 info->params.flags |= flags;
1662
1663 info->params.loopback = new_line.loopback;
1664
1665 if (flags & (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG))
1666 info->params.clock_speed = new_line.clock_rate;
1667 else
1668 info->params.clock_speed = 0;
1669
1670 /* if network interface up, reprogram hardware */
1671 if (info->netcount)
1672 program_hw(info);
1673 return 0;
1674
1675 default:
1676 return hdlc_ioctl(dev, ifr, cmd);
1677 }
1678 }
1679
1680 /**
1681 * called by network layer when transmit timeout is detected
1682 *
1683 * dev pointer to network device structure
1684 */
hdlcdev_tx_timeout(struct net_device * dev)1685 static void hdlcdev_tx_timeout(struct net_device *dev)
1686 {
1687 struct slgt_info *info = dev_to_port(dev);
1688 unsigned long flags;
1689
1690 DBGINFO(("%s hdlcdev_tx_timeout\n", dev->name));
1691
1692 dev->stats.tx_errors++;
1693 dev->stats.tx_aborted_errors++;
1694
1695 spin_lock_irqsave(&info->lock,flags);
1696 tx_stop(info);
1697 spin_unlock_irqrestore(&info->lock,flags);
1698
1699 netif_wake_queue(dev);
1700 }
1701
1702 /**
1703 * called by device driver when transmit completes
1704 * reenable network layer transmit if stopped
1705 *
1706 * info pointer to device instance information
1707 */
hdlcdev_tx_done(struct slgt_info * info)1708 static void hdlcdev_tx_done(struct slgt_info *info)
1709 {
1710 if (netif_queue_stopped(info->netdev))
1711 netif_wake_queue(info->netdev);
1712 }
1713
1714 /**
1715 * called by device driver when frame received
1716 * pass frame to network layer
1717 *
1718 * info pointer to device instance information
1719 * buf pointer to buffer contianing frame data
1720 * size count of data bytes in buf
1721 */
hdlcdev_rx(struct slgt_info * info,char * buf,int size)1722 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size)
1723 {
1724 struct sk_buff *skb = dev_alloc_skb(size);
1725 struct net_device *dev = info->netdev;
1726
1727 DBGINFO(("%s hdlcdev_rx\n", dev->name));
1728
1729 if (skb == NULL) {
1730 DBGERR(("%s: can't alloc skb, drop packet\n", dev->name));
1731 dev->stats.rx_dropped++;
1732 return;
1733 }
1734
1735 skb_put_data(skb, buf, size);
1736
1737 skb->protocol = hdlc_type_trans(skb, dev);
1738
1739 dev->stats.rx_packets++;
1740 dev->stats.rx_bytes += size;
1741
1742 netif_rx(skb);
1743 }
1744
1745 static const struct net_device_ops hdlcdev_ops = {
1746 .ndo_open = hdlcdev_open,
1747 .ndo_stop = hdlcdev_close,
1748 .ndo_start_xmit = hdlc_start_xmit,
1749 .ndo_do_ioctl = hdlcdev_ioctl,
1750 .ndo_tx_timeout = hdlcdev_tx_timeout,
1751 };
1752
1753 /**
1754 * called by device driver when adding device instance
1755 * do generic HDLC initialization
1756 *
1757 * info pointer to device instance information
1758 *
1759 * returns 0 if success, otherwise error code
1760 */
hdlcdev_init(struct slgt_info * info)1761 static int hdlcdev_init(struct slgt_info *info)
1762 {
1763 int rc;
1764 struct net_device *dev;
1765 hdlc_device *hdlc;
1766
1767 /* allocate and initialize network and HDLC layer objects */
1768
1769 dev = alloc_hdlcdev(info);
1770 if (!dev) {
1771 printk(KERN_ERR "%s hdlc device alloc failure\n", info->device_name);
1772 return -ENOMEM;
1773 }
1774
1775 /* for network layer reporting purposes only */
1776 dev->mem_start = info->phys_reg_addr;
1777 dev->mem_end = info->phys_reg_addr + SLGT_REG_SIZE - 1;
1778 dev->irq = info->irq_level;
1779
1780 /* network layer callbacks and settings */
1781 dev->netdev_ops = &hdlcdev_ops;
1782 dev->watchdog_timeo = 10 * HZ;
1783 dev->tx_queue_len = 50;
1784
1785 /* generic HDLC layer callbacks and settings */
1786 hdlc = dev_to_hdlc(dev);
1787 hdlc->attach = hdlcdev_attach;
1788 hdlc->xmit = hdlcdev_xmit;
1789
1790 /* register objects with HDLC layer */
1791 rc = register_hdlc_device(dev);
1792 if (rc) {
1793 printk(KERN_WARNING "%s:unable to register hdlc device\n",__FILE__);
1794 free_netdev(dev);
1795 return rc;
1796 }
1797
1798 info->netdev = dev;
1799 return 0;
1800 }
1801
1802 /**
1803 * called by device driver when removing device instance
1804 * do generic HDLC cleanup
1805 *
1806 * info pointer to device instance information
1807 */
hdlcdev_exit(struct slgt_info * info)1808 static void hdlcdev_exit(struct slgt_info *info)
1809 {
1810 unregister_hdlc_device(info->netdev);
1811 free_netdev(info->netdev);
1812 info->netdev = NULL;
1813 }
1814
1815 #endif /* ifdef CONFIG_HDLC */
1816
1817 /*
1818 * get async data from rx DMA buffers
1819 */
rx_async(struct slgt_info * info)1820 static void rx_async(struct slgt_info *info)
1821 {
1822 struct mgsl_icount *icount = &info->icount;
1823 unsigned int start, end;
1824 unsigned char *p;
1825 unsigned char status;
1826 struct slgt_desc *bufs = info->rbufs;
1827 int i, count;
1828 int chars = 0;
1829 int stat;
1830 unsigned char ch;
1831
1832 start = end = info->rbuf_current;
1833
1834 while(desc_complete(bufs[end])) {
1835 count = desc_count(bufs[end]) - info->rbuf_index;
1836 p = bufs[end].buf + info->rbuf_index;
1837
1838 DBGISR(("%s rx_async count=%d\n", info->device_name, count));
1839 DBGDATA(info, p, count, "rx");
1840
1841 for(i=0 ; i < count; i+=2, p+=2) {
1842 ch = *p;
1843 icount->rx++;
1844
1845 stat = 0;
1846
1847 status = *(p + 1) & (BIT1 + BIT0);
1848 if (status) {
1849 if (status & BIT1)
1850 icount->parity++;
1851 else if (status & BIT0)
1852 icount->frame++;
1853 /* discard char if tty control flags say so */
1854 if (status & info->ignore_status_mask)
1855 continue;
1856 if (status & BIT1)
1857 stat = TTY_PARITY;
1858 else if (status & BIT0)
1859 stat = TTY_FRAME;
1860 }
1861 tty_insert_flip_char(&info->port, ch, stat);
1862 chars++;
1863 }
1864
1865 if (i < count) {
1866 /* receive buffer not completed */
1867 info->rbuf_index += i;
1868 mod_timer(&info->rx_timer, jiffies + 1);
1869 break;
1870 }
1871
1872 info->rbuf_index = 0;
1873 free_rbufs(info, end, end);
1874
1875 if (++end == info->rbuf_count)
1876 end = 0;
1877
1878 /* if entire list searched then no frame available */
1879 if (end == start)
1880 break;
1881 }
1882
1883 if (chars)
1884 tty_flip_buffer_push(&info->port);
1885 }
1886
1887 /*
1888 * return next bottom half action to perform
1889 */
bh_action(struct slgt_info * info)1890 static int bh_action(struct slgt_info *info)
1891 {
1892 unsigned long flags;
1893 int rc;
1894
1895 spin_lock_irqsave(&info->lock,flags);
1896
1897 if (info->pending_bh & BH_RECEIVE) {
1898 info->pending_bh &= ~BH_RECEIVE;
1899 rc = BH_RECEIVE;
1900 } else if (info->pending_bh & BH_TRANSMIT) {
1901 info->pending_bh &= ~BH_TRANSMIT;
1902 rc = BH_TRANSMIT;
1903 } else if (info->pending_bh & BH_STATUS) {
1904 info->pending_bh &= ~BH_STATUS;
1905 rc = BH_STATUS;
1906 } else {
1907 /* Mark BH routine as complete */
1908 info->bh_running = false;
1909 info->bh_requested = false;
1910 rc = 0;
1911 }
1912
1913 spin_unlock_irqrestore(&info->lock,flags);
1914
1915 return rc;
1916 }
1917
1918 /*
1919 * perform bottom half processing
1920 */
bh_handler(struct work_struct * work)1921 static void bh_handler(struct work_struct *work)
1922 {
1923 struct slgt_info *info = container_of(work, struct slgt_info, task);
1924 int action;
1925
1926 info->bh_running = true;
1927
1928 while((action = bh_action(info))) {
1929 switch (action) {
1930 case BH_RECEIVE:
1931 DBGBH(("%s bh receive\n", info->device_name));
1932 switch(info->params.mode) {
1933 case MGSL_MODE_ASYNC:
1934 rx_async(info);
1935 break;
1936 case MGSL_MODE_HDLC:
1937 while(rx_get_frame(info));
1938 break;
1939 case MGSL_MODE_RAW:
1940 case MGSL_MODE_MONOSYNC:
1941 case MGSL_MODE_BISYNC:
1942 case MGSL_MODE_XSYNC:
1943 while(rx_get_buf(info));
1944 break;
1945 }
1946 /* restart receiver if rx DMA buffers exhausted */
1947 if (info->rx_restart)
1948 rx_start(info);
1949 break;
1950 case BH_TRANSMIT:
1951 bh_transmit(info);
1952 break;
1953 case BH_STATUS:
1954 DBGBH(("%s bh status\n", info->device_name));
1955 info->ri_chkcount = 0;
1956 info->dsr_chkcount = 0;
1957 info->dcd_chkcount = 0;
1958 info->cts_chkcount = 0;
1959 break;
1960 default:
1961 DBGBH(("%s unknown action\n", info->device_name));
1962 break;
1963 }
1964 }
1965 DBGBH(("%s bh_handler exit\n", info->device_name));
1966 }
1967
bh_transmit(struct slgt_info * info)1968 static void bh_transmit(struct slgt_info *info)
1969 {
1970 struct tty_struct *tty = info->port.tty;
1971
1972 DBGBH(("%s bh_transmit\n", info->device_name));
1973 if (tty)
1974 tty_wakeup(tty);
1975 }
1976
dsr_change(struct slgt_info * info,unsigned short status)1977 static void dsr_change(struct slgt_info *info, unsigned short status)
1978 {
1979 if (status & BIT3) {
1980 info->signals |= SerialSignal_DSR;
1981 info->input_signal_events.dsr_up++;
1982 } else {
1983 info->signals &= ~SerialSignal_DSR;
1984 info->input_signal_events.dsr_down++;
1985 }
1986 DBGISR(("dsr_change %s signals=%04X\n", info->device_name, info->signals));
1987 if ((info->dsr_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
1988 slgt_irq_off(info, IRQ_DSR);
1989 return;
1990 }
1991 info->icount.dsr++;
1992 wake_up_interruptible(&info->status_event_wait_q);
1993 wake_up_interruptible(&info->event_wait_q);
1994 info->pending_bh |= BH_STATUS;
1995 }
1996
cts_change(struct slgt_info * info,unsigned short status)1997 static void cts_change(struct slgt_info *info, unsigned short status)
1998 {
1999 if (status & BIT2) {
2000 info->signals |= SerialSignal_CTS;
2001 info->input_signal_events.cts_up++;
2002 } else {
2003 info->signals &= ~SerialSignal_CTS;
2004 info->input_signal_events.cts_down++;
2005 }
2006 DBGISR(("cts_change %s signals=%04X\n", info->device_name, info->signals));
2007 if ((info->cts_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2008 slgt_irq_off(info, IRQ_CTS);
2009 return;
2010 }
2011 info->icount.cts++;
2012 wake_up_interruptible(&info->status_event_wait_q);
2013 wake_up_interruptible(&info->event_wait_q);
2014 info->pending_bh |= BH_STATUS;
2015
2016 if (tty_port_cts_enabled(&info->port)) {
2017 if (info->port.tty) {
2018 if (info->port.tty->hw_stopped) {
2019 if (info->signals & SerialSignal_CTS) {
2020 info->port.tty->hw_stopped = 0;
2021 info->pending_bh |= BH_TRANSMIT;
2022 return;
2023 }
2024 } else {
2025 if (!(info->signals & SerialSignal_CTS))
2026 info->port.tty->hw_stopped = 1;
2027 }
2028 }
2029 }
2030 }
2031
dcd_change(struct slgt_info * info,unsigned short status)2032 static void dcd_change(struct slgt_info *info, unsigned short status)
2033 {
2034 if (status & BIT1) {
2035 info->signals |= SerialSignal_DCD;
2036 info->input_signal_events.dcd_up++;
2037 } else {
2038 info->signals &= ~SerialSignal_DCD;
2039 info->input_signal_events.dcd_down++;
2040 }
2041 DBGISR(("dcd_change %s signals=%04X\n", info->device_name, info->signals));
2042 if ((info->dcd_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2043 slgt_irq_off(info, IRQ_DCD);
2044 return;
2045 }
2046 info->icount.dcd++;
2047 #if SYNCLINK_GENERIC_HDLC
2048 if (info->netcount) {
2049 if (info->signals & SerialSignal_DCD)
2050 netif_carrier_on(info->netdev);
2051 else
2052 netif_carrier_off(info->netdev);
2053 }
2054 #endif
2055 wake_up_interruptible(&info->status_event_wait_q);
2056 wake_up_interruptible(&info->event_wait_q);
2057 info->pending_bh |= BH_STATUS;
2058
2059 if (tty_port_check_carrier(&info->port)) {
2060 if (info->signals & SerialSignal_DCD)
2061 wake_up_interruptible(&info->port.open_wait);
2062 else {
2063 if (info->port.tty)
2064 tty_hangup(info->port.tty);
2065 }
2066 }
2067 }
2068
ri_change(struct slgt_info * info,unsigned short status)2069 static void ri_change(struct slgt_info *info, unsigned short status)
2070 {
2071 if (status & BIT0) {
2072 info->signals |= SerialSignal_RI;
2073 info->input_signal_events.ri_up++;
2074 } else {
2075 info->signals &= ~SerialSignal_RI;
2076 info->input_signal_events.ri_down++;
2077 }
2078 DBGISR(("ri_change %s signals=%04X\n", info->device_name, info->signals));
2079 if ((info->ri_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2080 slgt_irq_off(info, IRQ_RI);
2081 return;
2082 }
2083 info->icount.rng++;
2084 wake_up_interruptible(&info->status_event_wait_q);
2085 wake_up_interruptible(&info->event_wait_q);
2086 info->pending_bh |= BH_STATUS;
2087 }
2088
isr_rxdata(struct slgt_info * info)2089 static void isr_rxdata(struct slgt_info *info)
2090 {
2091 unsigned int count = info->rbuf_fill_count;
2092 unsigned int i = info->rbuf_fill_index;
2093 unsigned short reg;
2094
2095 while (rd_reg16(info, SSR) & IRQ_RXDATA) {
2096 reg = rd_reg16(info, RDR);
2097 DBGISR(("isr_rxdata %s RDR=%04X\n", info->device_name, reg));
2098 if (desc_complete(info->rbufs[i])) {
2099 /* all buffers full */
2100 rx_stop(info);
2101 info->rx_restart = 1;
2102 continue;
2103 }
2104 info->rbufs[i].buf[count++] = (unsigned char)reg;
2105 /* async mode saves status byte to buffer for each data byte */
2106 if (info->params.mode == MGSL_MODE_ASYNC)
2107 info->rbufs[i].buf[count++] = (unsigned char)(reg >> 8);
2108 if (count == info->rbuf_fill_level || (reg & BIT10)) {
2109 /* buffer full or end of frame */
2110 set_desc_count(info->rbufs[i], count);
2111 set_desc_status(info->rbufs[i], BIT15 | (reg >> 8));
2112 info->rbuf_fill_count = count = 0;
2113 if (++i == info->rbuf_count)
2114 i = 0;
2115 info->pending_bh |= BH_RECEIVE;
2116 }
2117 }
2118
2119 info->rbuf_fill_index = i;
2120 info->rbuf_fill_count = count;
2121 }
2122
isr_serial(struct slgt_info * info)2123 static void isr_serial(struct slgt_info *info)
2124 {
2125 unsigned short status = rd_reg16(info, SSR);
2126
2127 DBGISR(("%s isr_serial status=%04X\n", info->device_name, status));
2128
2129 wr_reg16(info, SSR, status); /* clear pending */
2130
2131 info->irq_occurred = true;
2132
2133 if (info->params.mode == MGSL_MODE_ASYNC) {
2134 if (status & IRQ_TXIDLE) {
2135 if (info->tx_active)
2136 isr_txeom(info, status);
2137 }
2138 if (info->rx_pio && (status & IRQ_RXDATA))
2139 isr_rxdata(info);
2140 if ((status & IRQ_RXBREAK) && (status & RXBREAK)) {
2141 info->icount.brk++;
2142 /* process break detection if tty control allows */
2143 if (info->port.tty) {
2144 if (!(status & info->ignore_status_mask)) {
2145 if (info->read_status_mask & MASK_BREAK) {
2146 tty_insert_flip_char(&info->port, 0, TTY_BREAK);
2147 if (info->port.flags & ASYNC_SAK)
2148 do_SAK(info->port.tty);
2149 }
2150 }
2151 }
2152 }
2153 } else {
2154 if (status & (IRQ_TXIDLE + IRQ_TXUNDER))
2155 isr_txeom(info, status);
2156 if (info->rx_pio && (status & IRQ_RXDATA))
2157 isr_rxdata(info);
2158 if (status & IRQ_RXIDLE) {
2159 if (status & RXIDLE)
2160 info->icount.rxidle++;
2161 else
2162 info->icount.exithunt++;
2163 wake_up_interruptible(&info->event_wait_q);
2164 }
2165
2166 if (status & IRQ_RXOVER)
2167 rx_start(info);
2168 }
2169
2170 if (status & IRQ_DSR)
2171 dsr_change(info, status);
2172 if (status & IRQ_CTS)
2173 cts_change(info, status);
2174 if (status & IRQ_DCD)
2175 dcd_change(info, status);
2176 if (status & IRQ_RI)
2177 ri_change(info, status);
2178 }
2179
isr_rdma(struct slgt_info * info)2180 static void isr_rdma(struct slgt_info *info)
2181 {
2182 unsigned int status = rd_reg32(info, RDCSR);
2183
2184 DBGISR(("%s isr_rdma status=%08x\n", info->device_name, status));
2185
2186 /* RDCSR (rx DMA control/status)
2187 *
2188 * 31..07 reserved
2189 * 06 save status byte to DMA buffer
2190 * 05 error
2191 * 04 eol (end of list)
2192 * 03 eob (end of buffer)
2193 * 02 IRQ enable
2194 * 01 reset
2195 * 00 enable
2196 */
2197 wr_reg32(info, RDCSR, status); /* clear pending */
2198
2199 if (status & (BIT5 + BIT4)) {
2200 DBGISR(("%s isr_rdma rx_restart=1\n", info->device_name));
2201 info->rx_restart = true;
2202 }
2203 info->pending_bh |= BH_RECEIVE;
2204 }
2205
isr_tdma(struct slgt_info * info)2206 static void isr_tdma(struct slgt_info *info)
2207 {
2208 unsigned int status = rd_reg32(info, TDCSR);
2209
2210 DBGISR(("%s isr_tdma status=%08x\n", info->device_name, status));
2211
2212 /* TDCSR (tx DMA control/status)
2213 *
2214 * 31..06 reserved
2215 * 05 error
2216 * 04 eol (end of list)
2217 * 03 eob (end of buffer)
2218 * 02 IRQ enable
2219 * 01 reset
2220 * 00 enable
2221 */
2222 wr_reg32(info, TDCSR, status); /* clear pending */
2223
2224 if (status & (BIT5 + BIT4 + BIT3)) {
2225 // another transmit buffer has completed
2226 // run bottom half to get more send data from user
2227 info->pending_bh |= BH_TRANSMIT;
2228 }
2229 }
2230
2231 /*
2232 * return true if there are unsent tx DMA buffers, otherwise false
2233 *
2234 * if there are unsent buffers then info->tbuf_start
2235 * is set to index of first unsent buffer
2236 */
unsent_tbufs(struct slgt_info * info)2237 static bool unsent_tbufs(struct slgt_info *info)
2238 {
2239 unsigned int i = info->tbuf_current;
2240 bool rc = false;
2241
2242 /*
2243 * search backwards from last loaded buffer (precedes tbuf_current)
2244 * for first unsent buffer (desc_count > 0)
2245 */
2246
2247 do {
2248 if (i)
2249 i--;
2250 else
2251 i = info->tbuf_count - 1;
2252 if (!desc_count(info->tbufs[i]))
2253 break;
2254 info->tbuf_start = i;
2255 rc = true;
2256 } while (i != info->tbuf_current);
2257
2258 return rc;
2259 }
2260
isr_txeom(struct slgt_info * info,unsigned short status)2261 static void isr_txeom(struct slgt_info *info, unsigned short status)
2262 {
2263 DBGISR(("%s txeom status=%04x\n", info->device_name, status));
2264
2265 slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
2266 tdma_reset(info);
2267 if (status & IRQ_TXUNDER) {
2268 unsigned short val = rd_reg16(info, TCR);
2269 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
2270 wr_reg16(info, TCR, val); /* clear reset bit */
2271 }
2272
2273 if (info->tx_active) {
2274 if (info->params.mode != MGSL_MODE_ASYNC) {
2275 if (status & IRQ_TXUNDER)
2276 info->icount.txunder++;
2277 else if (status & IRQ_TXIDLE)
2278 info->icount.txok++;
2279 }
2280
2281 if (unsent_tbufs(info)) {
2282 tx_start(info);
2283 update_tx_timer(info);
2284 return;
2285 }
2286 info->tx_active = false;
2287
2288 del_timer(&info->tx_timer);
2289
2290 if (info->params.mode != MGSL_MODE_ASYNC && info->drop_rts_on_tx_done) {
2291 info->signals &= ~SerialSignal_RTS;
2292 info->drop_rts_on_tx_done = false;
2293 set_signals(info);
2294 }
2295
2296 #if SYNCLINK_GENERIC_HDLC
2297 if (info->netcount)
2298 hdlcdev_tx_done(info);
2299 else
2300 #endif
2301 {
2302 if (info->port.tty && (info->port.tty->stopped || info->port.tty->hw_stopped)) {
2303 tx_stop(info);
2304 return;
2305 }
2306 info->pending_bh |= BH_TRANSMIT;
2307 }
2308 }
2309 }
2310
isr_gpio(struct slgt_info * info,unsigned int changed,unsigned int state)2311 static void isr_gpio(struct slgt_info *info, unsigned int changed, unsigned int state)
2312 {
2313 struct cond_wait *w, *prev;
2314
2315 /* wake processes waiting for specific transitions */
2316 for (w = info->gpio_wait_q, prev = NULL ; w != NULL ; w = w->next) {
2317 if (w->data & changed) {
2318 w->data = state;
2319 wake_up_interruptible(&w->q);
2320 if (prev != NULL)
2321 prev->next = w->next;
2322 else
2323 info->gpio_wait_q = w->next;
2324 } else
2325 prev = w;
2326 }
2327 }
2328
2329 /* interrupt service routine
2330 *
2331 * irq interrupt number
2332 * dev_id device ID supplied during interrupt registration
2333 */
slgt_interrupt(int dummy,void * dev_id)2334 static irqreturn_t slgt_interrupt(int dummy, void *dev_id)
2335 {
2336 struct slgt_info *info = dev_id;
2337 unsigned int gsr;
2338 unsigned int i;
2339
2340 DBGISR(("slgt_interrupt irq=%d entry\n", info->irq_level));
2341
2342 while((gsr = rd_reg32(info, GSR) & 0xffffff00)) {
2343 DBGISR(("%s gsr=%08x\n", info->device_name, gsr));
2344 info->irq_occurred = true;
2345 for(i=0; i < info->port_count ; i++) {
2346 if (info->port_array[i] == NULL)
2347 continue;
2348 spin_lock(&info->port_array[i]->lock);
2349 if (gsr & (BIT8 << i))
2350 isr_serial(info->port_array[i]);
2351 if (gsr & (BIT16 << (i*2)))
2352 isr_rdma(info->port_array[i]);
2353 if (gsr & (BIT17 << (i*2)))
2354 isr_tdma(info->port_array[i]);
2355 spin_unlock(&info->port_array[i]->lock);
2356 }
2357 }
2358
2359 if (info->gpio_present) {
2360 unsigned int state;
2361 unsigned int changed;
2362 spin_lock(&info->lock);
2363 while ((changed = rd_reg32(info, IOSR)) != 0) {
2364 DBGISR(("%s iosr=%08x\n", info->device_name, changed));
2365 /* read latched state of GPIO signals */
2366 state = rd_reg32(info, IOVR);
2367 /* clear pending GPIO interrupt bits */
2368 wr_reg32(info, IOSR, changed);
2369 for (i=0 ; i < info->port_count ; i++) {
2370 if (info->port_array[i] != NULL)
2371 isr_gpio(info->port_array[i], changed, state);
2372 }
2373 }
2374 spin_unlock(&info->lock);
2375 }
2376
2377 for(i=0; i < info->port_count ; i++) {
2378 struct slgt_info *port = info->port_array[i];
2379 if (port == NULL)
2380 continue;
2381 spin_lock(&port->lock);
2382 if ((port->port.count || port->netcount) &&
2383 port->pending_bh && !port->bh_running &&
2384 !port->bh_requested) {
2385 DBGISR(("%s bh queued\n", port->device_name));
2386 schedule_work(&port->task);
2387 port->bh_requested = true;
2388 }
2389 spin_unlock(&port->lock);
2390 }
2391
2392 DBGISR(("slgt_interrupt irq=%d exit\n", info->irq_level));
2393 return IRQ_HANDLED;
2394 }
2395
startup(struct slgt_info * info)2396 static int startup(struct slgt_info *info)
2397 {
2398 DBGINFO(("%s startup\n", info->device_name));
2399
2400 if (tty_port_initialized(&info->port))
2401 return 0;
2402
2403 if (!info->tx_buf) {
2404 info->tx_buf = kmalloc(info->max_frame_size, GFP_KERNEL);
2405 if (!info->tx_buf) {
2406 DBGERR(("%s can't allocate tx buffer\n", info->device_name));
2407 return -ENOMEM;
2408 }
2409 }
2410
2411 info->pending_bh = 0;
2412
2413 memset(&info->icount, 0, sizeof(info->icount));
2414
2415 /* program hardware for current parameters */
2416 change_params(info);
2417
2418 if (info->port.tty)
2419 clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
2420
2421 tty_port_set_initialized(&info->port, 1);
2422
2423 return 0;
2424 }
2425
2426 /*
2427 * called by close() and hangup() to shutdown hardware
2428 */
shutdown(struct slgt_info * info)2429 static void shutdown(struct slgt_info *info)
2430 {
2431 unsigned long flags;
2432
2433 if (!tty_port_initialized(&info->port))
2434 return;
2435
2436 DBGINFO(("%s shutdown\n", info->device_name));
2437
2438 /* clear status wait queue because status changes */
2439 /* can't happen after shutting down the hardware */
2440 wake_up_interruptible(&info->status_event_wait_q);
2441 wake_up_interruptible(&info->event_wait_q);
2442
2443 del_timer_sync(&info->tx_timer);
2444 del_timer_sync(&info->rx_timer);
2445
2446 kfree(info->tx_buf);
2447 info->tx_buf = NULL;
2448
2449 spin_lock_irqsave(&info->lock,flags);
2450
2451 tx_stop(info);
2452 rx_stop(info);
2453
2454 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
2455
2456 if (!info->port.tty || info->port.tty->termios.c_cflag & HUPCL) {
2457 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
2458 set_signals(info);
2459 }
2460
2461 flush_cond_wait(&info->gpio_wait_q);
2462
2463 spin_unlock_irqrestore(&info->lock,flags);
2464
2465 if (info->port.tty)
2466 set_bit(TTY_IO_ERROR, &info->port.tty->flags);
2467
2468 tty_port_set_initialized(&info->port, 0);
2469 }
2470
program_hw(struct slgt_info * info)2471 static void program_hw(struct slgt_info *info)
2472 {
2473 unsigned long flags;
2474
2475 spin_lock_irqsave(&info->lock,flags);
2476
2477 rx_stop(info);
2478 tx_stop(info);
2479
2480 if (info->params.mode != MGSL_MODE_ASYNC ||
2481 info->netcount)
2482 sync_mode(info);
2483 else
2484 async_mode(info);
2485
2486 set_signals(info);
2487
2488 info->dcd_chkcount = 0;
2489 info->cts_chkcount = 0;
2490 info->ri_chkcount = 0;
2491 info->dsr_chkcount = 0;
2492
2493 slgt_irq_on(info, IRQ_DCD | IRQ_CTS | IRQ_DSR | IRQ_RI);
2494 get_signals(info);
2495
2496 if (info->netcount ||
2497 (info->port.tty && info->port.tty->termios.c_cflag & CREAD))
2498 rx_start(info);
2499
2500 spin_unlock_irqrestore(&info->lock,flags);
2501 }
2502
2503 /*
2504 * reconfigure adapter based on new parameters
2505 */
change_params(struct slgt_info * info)2506 static void change_params(struct slgt_info *info)
2507 {
2508 unsigned cflag;
2509 int bits_per_char;
2510
2511 if (!info->port.tty)
2512 return;
2513 DBGINFO(("%s change_params\n", info->device_name));
2514
2515 cflag = info->port.tty->termios.c_cflag;
2516
2517 /* if B0 rate (hangup) specified then negate RTS and DTR */
2518 /* otherwise assert RTS and DTR */
2519 if (cflag & CBAUD)
2520 info->signals |= SerialSignal_RTS | SerialSignal_DTR;
2521 else
2522 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
2523
2524 /* byte size and parity */
2525
2526 switch (cflag & CSIZE) {
2527 case CS5: info->params.data_bits = 5; break;
2528 case CS6: info->params.data_bits = 6; break;
2529 case CS7: info->params.data_bits = 7; break;
2530 case CS8: info->params.data_bits = 8; break;
2531 default: info->params.data_bits = 7; break;
2532 }
2533
2534 info->params.stop_bits = (cflag & CSTOPB) ? 2 : 1;
2535
2536 if (cflag & PARENB)
2537 info->params.parity = (cflag & PARODD) ? ASYNC_PARITY_ODD : ASYNC_PARITY_EVEN;
2538 else
2539 info->params.parity = ASYNC_PARITY_NONE;
2540
2541 /* calculate number of jiffies to transmit a full
2542 * FIFO (32 bytes) at specified data rate
2543 */
2544 bits_per_char = info->params.data_bits +
2545 info->params.stop_bits + 1;
2546
2547 info->params.data_rate = tty_get_baud_rate(info->port.tty);
2548
2549 if (info->params.data_rate) {
2550 info->timeout = (32*HZ*bits_per_char) /
2551 info->params.data_rate;
2552 }
2553 info->timeout += HZ/50; /* Add .02 seconds of slop */
2554
2555 tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
2556 tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
2557
2558 /* process tty input control flags */
2559
2560 info->read_status_mask = IRQ_RXOVER;
2561 if (I_INPCK(info->port.tty))
2562 info->read_status_mask |= MASK_PARITY | MASK_FRAMING;
2563 if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
2564 info->read_status_mask |= MASK_BREAK;
2565 if (I_IGNPAR(info->port.tty))
2566 info->ignore_status_mask |= MASK_PARITY | MASK_FRAMING;
2567 if (I_IGNBRK(info->port.tty)) {
2568 info->ignore_status_mask |= MASK_BREAK;
2569 /* If ignoring parity and break indicators, ignore
2570 * overruns too. (For real raw support).
2571 */
2572 if (I_IGNPAR(info->port.tty))
2573 info->ignore_status_mask |= MASK_OVERRUN;
2574 }
2575
2576 program_hw(info);
2577 }
2578
get_stats(struct slgt_info * info,struct mgsl_icount __user * user_icount)2579 static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount)
2580 {
2581 DBGINFO(("%s get_stats\n", info->device_name));
2582 if (!user_icount) {
2583 memset(&info->icount, 0, sizeof(info->icount));
2584 } else {
2585 if (copy_to_user(user_icount, &info->icount, sizeof(struct mgsl_icount)))
2586 return -EFAULT;
2587 }
2588 return 0;
2589 }
2590
get_params(struct slgt_info * info,MGSL_PARAMS __user * user_params)2591 static int get_params(struct slgt_info *info, MGSL_PARAMS __user *user_params)
2592 {
2593 DBGINFO(("%s get_params\n", info->device_name));
2594 if (copy_to_user(user_params, &info->params, sizeof(MGSL_PARAMS)))
2595 return -EFAULT;
2596 return 0;
2597 }
2598
set_params(struct slgt_info * info,MGSL_PARAMS __user * new_params)2599 static int set_params(struct slgt_info *info, MGSL_PARAMS __user *new_params)
2600 {
2601 unsigned long flags;
2602 MGSL_PARAMS tmp_params;
2603
2604 DBGINFO(("%s set_params\n", info->device_name));
2605 if (copy_from_user(&tmp_params, new_params, sizeof(MGSL_PARAMS)))
2606 return -EFAULT;
2607
2608 spin_lock_irqsave(&info->lock, flags);
2609 if (tmp_params.mode == MGSL_MODE_BASE_CLOCK)
2610 info->base_clock = tmp_params.clock_speed;
2611 else
2612 memcpy(&info->params, &tmp_params, sizeof(MGSL_PARAMS));
2613 spin_unlock_irqrestore(&info->lock, flags);
2614
2615 program_hw(info);
2616
2617 return 0;
2618 }
2619
get_txidle(struct slgt_info * info,int __user * idle_mode)2620 static int get_txidle(struct slgt_info *info, int __user *idle_mode)
2621 {
2622 DBGINFO(("%s get_txidle=%d\n", info->device_name, info->idle_mode));
2623 if (put_user(info->idle_mode, idle_mode))
2624 return -EFAULT;
2625 return 0;
2626 }
2627
set_txidle(struct slgt_info * info,int idle_mode)2628 static int set_txidle(struct slgt_info *info, int idle_mode)
2629 {
2630 unsigned long flags;
2631 DBGINFO(("%s set_txidle(%d)\n", info->device_name, idle_mode));
2632 spin_lock_irqsave(&info->lock,flags);
2633 info->idle_mode = idle_mode;
2634 if (info->params.mode != MGSL_MODE_ASYNC)
2635 tx_set_idle(info);
2636 spin_unlock_irqrestore(&info->lock,flags);
2637 return 0;
2638 }
2639
tx_enable(struct slgt_info * info,int enable)2640 static int tx_enable(struct slgt_info *info, int enable)
2641 {
2642 unsigned long flags;
2643 DBGINFO(("%s tx_enable(%d)\n", info->device_name, enable));
2644 spin_lock_irqsave(&info->lock,flags);
2645 if (enable) {
2646 if (!info->tx_enabled)
2647 tx_start(info);
2648 } else {
2649 if (info->tx_enabled)
2650 tx_stop(info);
2651 }
2652 spin_unlock_irqrestore(&info->lock,flags);
2653 return 0;
2654 }
2655
2656 /*
2657 * abort transmit HDLC frame
2658 */
tx_abort(struct slgt_info * info)2659 static int tx_abort(struct slgt_info *info)
2660 {
2661 unsigned long flags;
2662 DBGINFO(("%s tx_abort\n", info->device_name));
2663 spin_lock_irqsave(&info->lock,flags);
2664 tdma_reset(info);
2665 spin_unlock_irqrestore(&info->lock,flags);
2666 return 0;
2667 }
2668
rx_enable(struct slgt_info * info,int enable)2669 static int rx_enable(struct slgt_info *info, int enable)
2670 {
2671 unsigned long flags;
2672 unsigned int rbuf_fill_level;
2673 DBGINFO(("%s rx_enable(%08x)\n", info->device_name, enable));
2674 spin_lock_irqsave(&info->lock,flags);
2675 /*
2676 * enable[31..16] = receive DMA buffer fill level
2677 * 0 = noop (leave fill level unchanged)
2678 * fill level must be multiple of 4 and <= buffer size
2679 */
2680 rbuf_fill_level = ((unsigned int)enable) >> 16;
2681 if (rbuf_fill_level) {
2682 if ((rbuf_fill_level > DMABUFSIZE) || (rbuf_fill_level % 4)) {
2683 spin_unlock_irqrestore(&info->lock, flags);
2684 return -EINVAL;
2685 }
2686 info->rbuf_fill_level = rbuf_fill_level;
2687 if (rbuf_fill_level < 128)
2688 info->rx_pio = 1; /* PIO mode */
2689 else
2690 info->rx_pio = 0; /* DMA mode */
2691 rx_stop(info); /* restart receiver to use new fill level */
2692 }
2693
2694 /*
2695 * enable[1..0] = receiver enable command
2696 * 0 = disable
2697 * 1 = enable
2698 * 2 = enable or force hunt mode if already enabled
2699 */
2700 enable &= 3;
2701 if (enable) {
2702 if (!info->rx_enabled)
2703 rx_start(info);
2704 else if (enable == 2) {
2705 /* force hunt mode (write 1 to RCR[3]) */
2706 wr_reg16(info, RCR, rd_reg16(info, RCR) | BIT3);
2707 }
2708 } else {
2709 if (info->rx_enabled)
2710 rx_stop(info);
2711 }
2712 spin_unlock_irqrestore(&info->lock,flags);
2713 return 0;
2714 }
2715
2716 /*
2717 * wait for specified event to occur
2718 */
wait_mgsl_event(struct slgt_info * info,int __user * mask_ptr)2719 static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr)
2720 {
2721 unsigned long flags;
2722 int s;
2723 int rc=0;
2724 struct mgsl_icount cprev, cnow;
2725 int events;
2726 int mask;
2727 struct _input_signal_events oldsigs, newsigs;
2728 DECLARE_WAITQUEUE(wait, current);
2729
2730 if (get_user(mask, mask_ptr))
2731 return -EFAULT;
2732
2733 DBGINFO(("%s wait_mgsl_event(%d)\n", info->device_name, mask));
2734
2735 spin_lock_irqsave(&info->lock,flags);
2736
2737 /* return immediately if state matches requested events */
2738 get_signals(info);
2739 s = info->signals;
2740
2741 events = mask &
2742 ( ((s & SerialSignal_DSR) ? MgslEvent_DsrActive:MgslEvent_DsrInactive) +
2743 ((s & SerialSignal_DCD) ? MgslEvent_DcdActive:MgslEvent_DcdInactive) +
2744 ((s & SerialSignal_CTS) ? MgslEvent_CtsActive:MgslEvent_CtsInactive) +
2745 ((s & SerialSignal_RI) ? MgslEvent_RiActive :MgslEvent_RiInactive) );
2746 if (events) {
2747 spin_unlock_irqrestore(&info->lock,flags);
2748 goto exit;
2749 }
2750
2751 /* save current irq counts */
2752 cprev = info->icount;
2753 oldsigs = info->input_signal_events;
2754
2755 /* enable hunt and idle irqs if needed */
2756 if (mask & (MgslEvent_ExitHuntMode+MgslEvent_IdleReceived)) {
2757 unsigned short val = rd_reg16(info, SCR);
2758 if (!(val & IRQ_RXIDLE))
2759 wr_reg16(info, SCR, (unsigned short)(val | IRQ_RXIDLE));
2760 }
2761
2762 set_current_state(TASK_INTERRUPTIBLE);
2763 add_wait_queue(&info->event_wait_q, &wait);
2764
2765 spin_unlock_irqrestore(&info->lock,flags);
2766
2767 for(;;) {
2768 schedule();
2769 if (signal_pending(current)) {
2770 rc = -ERESTARTSYS;
2771 break;
2772 }
2773
2774 /* get current irq counts */
2775 spin_lock_irqsave(&info->lock,flags);
2776 cnow = info->icount;
2777 newsigs = info->input_signal_events;
2778 set_current_state(TASK_INTERRUPTIBLE);
2779 spin_unlock_irqrestore(&info->lock,flags);
2780
2781 /* if no change, wait aborted for some reason */
2782 if (newsigs.dsr_up == oldsigs.dsr_up &&
2783 newsigs.dsr_down == oldsigs.dsr_down &&
2784 newsigs.dcd_up == oldsigs.dcd_up &&
2785 newsigs.dcd_down == oldsigs.dcd_down &&
2786 newsigs.cts_up == oldsigs.cts_up &&
2787 newsigs.cts_down == oldsigs.cts_down &&
2788 newsigs.ri_up == oldsigs.ri_up &&
2789 newsigs.ri_down == oldsigs.ri_down &&
2790 cnow.exithunt == cprev.exithunt &&
2791 cnow.rxidle == cprev.rxidle) {
2792 rc = -EIO;
2793 break;
2794 }
2795
2796 events = mask &
2797 ( (newsigs.dsr_up != oldsigs.dsr_up ? MgslEvent_DsrActive:0) +
2798 (newsigs.dsr_down != oldsigs.dsr_down ? MgslEvent_DsrInactive:0) +
2799 (newsigs.dcd_up != oldsigs.dcd_up ? MgslEvent_DcdActive:0) +
2800 (newsigs.dcd_down != oldsigs.dcd_down ? MgslEvent_DcdInactive:0) +
2801 (newsigs.cts_up != oldsigs.cts_up ? MgslEvent_CtsActive:0) +
2802 (newsigs.cts_down != oldsigs.cts_down ? MgslEvent_CtsInactive:0) +
2803 (newsigs.ri_up != oldsigs.ri_up ? MgslEvent_RiActive:0) +
2804 (newsigs.ri_down != oldsigs.ri_down ? MgslEvent_RiInactive:0) +
2805 (cnow.exithunt != cprev.exithunt ? MgslEvent_ExitHuntMode:0) +
2806 (cnow.rxidle != cprev.rxidle ? MgslEvent_IdleReceived:0) );
2807 if (events)
2808 break;
2809
2810 cprev = cnow;
2811 oldsigs = newsigs;
2812 }
2813
2814 remove_wait_queue(&info->event_wait_q, &wait);
2815 set_current_state(TASK_RUNNING);
2816
2817
2818 if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) {
2819 spin_lock_irqsave(&info->lock,flags);
2820 if (!waitqueue_active(&info->event_wait_q)) {
2821 /* disable enable exit hunt mode/idle rcvd IRQs */
2822 wr_reg16(info, SCR,
2823 (unsigned short)(rd_reg16(info, SCR) & ~IRQ_RXIDLE));
2824 }
2825 spin_unlock_irqrestore(&info->lock,flags);
2826 }
2827 exit:
2828 if (rc == 0)
2829 rc = put_user(events, mask_ptr);
2830 return rc;
2831 }
2832
get_interface(struct slgt_info * info,int __user * if_mode)2833 static int get_interface(struct slgt_info *info, int __user *if_mode)
2834 {
2835 DBGINFO(("%s get_interface=%x\n", info->device_name, info->if_mode));
2836 if (put_user(info->if_mode, if_mode))
2837 return -EFAULT;
2838 return 0;
2839 }
2840
set_interface(struct slgt_info * info,int if_mode)2841 static int set_interface(struct slgt_info *info, int if_mode)
2842 {
2843 unsigned long flags;
2844 unsigned short val;
2845
2846 DBGINFO(("%s set_interface=%x)\n", info->device_name, if_mode));
2847 spin_lock_irqsave(&info->lock,flags);
2848 info->if_mode = if_mode;
2849
2850 msc_set_vcr(info);
2851
2852 /* TCR (tx control) 07 1=RTS driver control */
2853 val = rd_reg16(info, TCR);
2854 if (info->if_mode & MGSL_INTERFACE_RTS_EN)
2855 val |= BIT7;
2856 else
2857 val &= ~BIT7;
2858 wr_reg16(info, TCR, val);
2859
2860 spin_unlock_irqrestore(&info->lock,flags);
2861 return 0;
2862 }
2863
get_xsync(struct slgt_info * info,int __user * xsync)2864 static int get_xsync(struct slgt_info *info, int __user *xsync)
2865 {
2866 DBGINFO(("%s get_xsync=%x\n", info->device_name, info->xsync));
2867 if (put_user(info->xsync, xsync))
2868 return -EFAULT;
2869 return 0;
2870 }
2871
2872 /*
2873 * set extended sync pattern (1 to 4 bytes) for extended sync mode
2874 *
2875 * sync pattern is contained in least significant bytes of value
2876 * most significant byte of sync pattern is oldest (1st sent/detected)
2877 */
set_xsync(struct slgt_info * info,int xsync)2878 static int set_xsync(struct slgt_info *info, int xsync)
2879 {
2880 unsigned long flags;
2881
2882 DBGINFO(("%s set_xsync=%x)\n", info->device_name, xsync));
2883 spin_lock_irqsave(&info->lock, flags);
2884 info->xsync = xsync;
2885 wr_reg32(info, XSR, xsync);
2886 spin_unlock_irqrestore(&info->lock, flags);
2887 return 0;
2888 }
2889
get_xctrl(struct slgt_info * info,int __user * xctrl)2890 static int get_xctrl(struct slgt_info *info, int __user *xctrl)
2891 {
2892 DBGINFO(("%s get_xctrl=%x\n", info->device_name, info->xctrl));
2893 if (put_user(info->xctrl, xctrl))
2894 return -EFAULT;
2895 return 0;
2896 }
2897
2898 /*
2899 * set extended control options
2900 *
2901 * xctrl[31:19] reserved, must be zero
2902 * xctrl[18:17] extended sync pattern length in bytes
2903 * 00 = 1 byte in xsr[7:0]
2904 * 01 = 2 bytes in xsr[15:0]
2905 * 10 = 3 bytes in xsr[23:0]
2906 * 11 = 4 bytes in xsr[31:0]
2907 * xctrl[16] 1 = enable terminal count, 0=disabled
2908 * xctrl[15:0] receive terminal count for fixed length packets
2909 * value is count minus one (0 = 1 byte packet)
2910 * when terminal count is reached, receiver
2911 * automatically returns to hunt mode and receive
2912 * FIFO contents are flushed to DMA buffers with
2913 * end of frame (EOF) status
2914 */
set_xctrl(struct slgt_info * info,int xctrl)2915 static int set_xctrl(struct slgt_info *info, int xctrl)
2916 {
2917 unsigned long flags;
2918
2919 DBGINFO(("%s set_xctrl=%x)\n", info->device_name, xctrl));
2920 spin_lock_irqsave(&info->lock, flags);
2921 info->xctrl = xctrl;
2922 wr_reg32(info, XCR, xctrl);
2923 spin_unlock_irqrestore(&info->lock, flags);
2924 return 0;
2925 }
2926
2927 /*
2928 * set general purpose IO pin state and direction
2929 *
2930 * user_gpio fields:
2931 * state each bit indicates a pin state
2932 * smask set bit indicates pin state to set
2933 * dir each bit indicates a pin direction (0=input, 1=output)
2934 * dmask set bit indicates pin direction to set
2935 */
set_gpio(struct slgt_info * info,struct gpio_desc __user * user_gpio)2936 static int set_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2937 {
2938 unsigned long flags;
2939 struct gpio_desc gpio;
2940 __u32 data;
2941
2942 if (!info->gpio_present)
2943 return -EINVAL;
2944 if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2945 return -EFAULT;
2946 DBGINFO(("%s set_gpio state=%08x smask=%08x dir=%08x dmask=%08x\n",
2947 info->device_name, gpio.state, gpio.smask,
2948 gpio.dir, gpio.dmask));
2949
2950 spin_lock_irqsave(&info->port_array[0]->lock, flags);
2951 if (gpio.dmask) {
2952 data = rd_reg32(info, IODR);
2953 data |= gpio.dmask & gpio.dir;
2954 data &= ~(gpio.dmask & ~gpio.dir);
2955 wr_reg32(info, IODR, data);
2956 }
2957 if (gpio.smask) {
2958 data = rd_reg32(info, IOVR);
2959 data |= gpio.smask & gpio.state;
2960 data &= ~(gpio.smask & ~gpio.state);
2961 wr_reg32(info, IOVR, data);
2962 }
2963 spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
2964
2965 return 0;
2966 }
2967
2968 /*
2969 * get general purpose IO pin state and direction
2970 */
get_gpio(struct slgt_info * info,struct gpio_desc __user * user_gpio)2971 static int get_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2972 {
2973 struct gpio_desc gpio;
2974 if (!info->gpio_present)
2975 return -EINVAL;
2976 gpio.state = rd_reg32(info, IOVR);
2977 gpio.smask = 0xffffffff;
2978 gpio.dir = rd_reg32(info, IODR);
2979 gpio.dmask = 0xffffffff;
2980 if (copy_to_user(user_gpio, &gpio, sizeof(gpio)))
2981 return -EFAULT;
2982 DBGINFO(("%s get_gpio state=%08x dir=%08x\n",
2983 info->device_name, gpio.state, gpio.dir));
2984 return 0;
2985 }
2986
2987 /*
2988 * conditional wait facility
2989 */
init_cond_wait(struct cond_wait * w,unsigned int data)2990 static void init_cond_wait(struct cond_wait *w, unsigned int data)
2991 {
2992 init_waitqueue_head(&w->q);
2993 init_waitqueue_entry(&w->wait, current);
2994 w->data = data;
2995 }
2996
add_cond_wait(struct cond_wait ** head,struct cond_wait * w)2997 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w)
2998 {
2999 set_current_state(TASK_INTERRUPTIBLE);
3000 add_wait_queue(&w->q, &w->wait);
3001 w->next = *head;
3002 *head = w;
3003 }
3004
remove_cond_wait(struct cond_wait ** head,struct cond_wait * cw)3005 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *cw)
3006 {
3007 struct cond_wait *w, *prev;
3008 remove_wait_queue(&cw->q, &cw->wait);
3009 set_current_state(TASK_RUNNING);
3010 for (w = *head, prev = NULL ; w != NULL ; prev = w, w = w->next) {
3011 if (w == cw) {
3012 if (prev != NULL)
3013 prev->next = w->next;
3014 else
3015 *head = w->next;
3016 break;
3017 }
3018 }
3019 }
3020
flush_cond_wait(struct cond_wait ** head)3021 static void flush_cond_wait(struct cond_wait **head)
3022 {
3023 while (*head != NULL) {
3024 wake_up_interruptible(&(*head)->q);
3025 *head = (*head)->next;
3026 }
3027 }
3028
3029 /*
3030 * wait for general purpose I/O pin(s) to enter specified state
3031 *
3032 * user_gpio fields:
3033 * state - bit indicates target pin state
3034 * smask - set bit indicates watched pin
3035 *
3036 * The wait ends when at least one watched pin enters the specified
3037 * state. When 0 (no error) is returned, user_gpio->state is set to the
3038 * state of all GPIO pins when the wait ends.
3039 *
3040 * Note: Each pin may be a dedicated input, dedicated output, or
3041 * configurable input/output. The number and configuration of pins
3042 * varies with the specific adapter model. Only input pins (dedicated
3043 * or configured) can be monitored with this function.
3044 */
wait_gpio(struct slgt_info * info,struct gpio_desc __user * user_gpio)3045 static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
3046 {
3047 unsigned long flags;
3048 int rc = 0;
3049 struct gpio_desc gpio;
3050 struct cond_wait wait;
3051 u32 state;
3052
3053 if (!info->gpio_present)
3054 return -EINVAL;
3055 if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
3056 return -EFAULT;
3057 DBGINFO(("%s wait_gpio() state=%08x smask=%08x\n",
3058 info->device_name, gpio.state, gpio.smask));
3059 /* ignore output pins identified by set IODR bit */
3060 if ((gpio.smask &= ~rd_reg32(info, IODR)) == 0)
3061 return -EINVAL;
3062 init_cond_wait(&wait, gpio.smask);
3063
3064 spin_lock_irqsave(&info->port_array[0]->lock, flags);
3065 /* enable interrupts for watched pins */
3066 wr_reg32(info, IOER, rd_reg32(info, IOER) | gpio.smask);
3067 /* get current pin states */
3068 state = rd_reg32(info, IOVR);
3069
3070 if (gpio.smask & ~(state ^ gpio.state)) {
3071 /* already in target state */
3072 gpio.state = state;
3073 } else {
3074 /* wait for target state */
3075 add_cond_wait(&info->gpio_wait_q, &wait);
3076 spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
3077 schedule();
3078 if (signal_pending(current))
3079 rc = -ERESTARTSYS;
3080 else
3081 gpio.state = wait.data;
3082 spin_lock_irqsave(&info->port_array[0]->lock, flags);
3083 remove_cond_wait(&info->gpio_wait_q, &wait);
3084 }
3085
3086 /* disable all GPIO interrupts if no waiting processes */
3087 if (info->gpio_wait_q == NULL)
3088 wr_reg32(info, IOER, 0);
3089 spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
3090
3091 if ((rc == 0) && copy_to_user(user_gpio, &gpio, sizeof(gpio)))
3092 rc = -EFAULT;
3093 return rc;
3094 }
3095
modem_input_wait(struct slgt_info * info,int arg)3096 static int modem_input_wait(struct slgt_info *info,int arg)
3097 {
3098 unsigned long flags;
3099 int rc;
3100 struct mgsl_icount cprev, cnow;
3101 DECLARE_WAITQUEUE(wait, current);
3102
3103 /* save current irq counts */
3104 spin_lock_irqsave(&info->lock,flags);
3105 cprev = info->icount;
3106 add_wait_queue(&info->status_event_wait_q, &wait);
3107 set_current_state(TASK_INTERRUPTIBLE);
3108 spin_unlock_irqrestore(&info->lock,flags);
3109
3110 for(;;) {
3111 schedule();
3112 if (signal_pending(current)) {
3113 rc = -ERESTARTSYS;
3114 break;
3115 }
3116
3117 /* get new irq counts */
3118 spin_lock_irqsave(&info->lock,flags);
3119 cnow = info->icount;
3120 set_current_state(TASK_INTERRUPTIBLE);
3121 spin_unlock_irqrestore(&info->lock,flags);
3122
3123 /* if no change, wait aborted for some reason */
3124 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
3125 cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) {
3126 rc = -EIO;
3127 break;
3128 }
3129
3130 /* check for change in caller specified modem input */
3131 if ((arg & TIOCM_RNG && cnow.rng != cprev.rng) ||
3132 (arg & TIOCM_DSR && cnow.dsr != cprev.dsr) ||
3133 (arg & TIOCM_CD && cnow.dcd != cprev.dcd) ||
3134 (arg & TIOCM_CTS && cnow.cts != cprev.cts)) {
3135 rc = 0;
3136 break;
3137 }
3138
3139 cprev = cnow;
3140 }
3141 remove_wait_queue(&info->status_event_wait_q, &wait);
3142 set_current_state(TASK_RUNNING);
3143 return rc;
3144 }
3145
3146 /*
3147 * return state of serial control and status signals
3148 */
tiocmget(struct tty_struct * tty)3149 static int tiocmget(struct tty_struct *tty)
3150 {
3151 struct slgt_info *info = tty->driver_data;
3152 unsigned int result;
3153 unsigned long flags;
3154
3155 spin_lock_irqsave(&info->lock,flags);
3156 get_signals(info);
3157 spin_unlock_irqrestore(&info->lock,flags);
3158
3159 result = ((info->signals & SerialSignal_RTS) ? TIOCM_RTS:0) +
3160 ((info->signals & SerialSignal_DTR) ? TIOCM_DTR:0) +
3161 ((info->signals & SerialSignal_DCD) ? TIOCM_CAR:0) +
3162 ((info->signals & SerialSignal_RI) ? TIOCM_RNG:0) +
3163 ((info->signals & SerialSignal_DSR) ? TIOCM_DSR:0) +
3164 ((info->signals & SerialSignal_CTS) ? TIOCM_CTS:0);
3165
3166 DBGINFO(("%s tiocmget value=%08X\n", info->device_name, result));
3167 return result;
3168 }
3169
3170 /*
3171 * set modem control signals (DTR/RTS)
3172 *
3173 * cmd signal command: TIOCMBIS = set bit TIOCMBIC = clear bit
3174 * TIOCMSET = set/clear signal values
3175 * value bit mask for command
3176 */
tiocmset(struct tty_struct * tty,unsigned int set,unsigned int clear)3177 static int tiocmset(struct tty_struct *tty,
3178 unsigned int set, unsigned int clear)
3179 {
3180 struct slgt_info *info = tty->driver_data;
3181 unsigned long flags;
3182
3183 DBGINFO(("%s tiocmset(%x,%x)\n", info->device_name, set, clear));
3184
3185 if (set & TIOCM_RTS)
3186 info->signals |= SerialSignal_RTS;
3187 if (set & TIOCM_DTR)
3188 info->signals |= SerialSignal_DTR;
3189 if (clear & TIOCM_RTS)
3190 info->signals &= ~SerialSignal_RTS;
3191 if (clear & TIOCM_DTR)
3192 info->signals &= ~SerialSignal_DTR;
3193
3194 spin_lock_irqsave(&info->lock,flags);
3195 set_signals(info);
3196 spin_unlock_irqrestore(&info->lock,flags);
3197 return 0;
3198 }
3199
carrier_raised(struct tty_port * port)3200 static int carrier_raised(struct tty_port *port)
3201 {
3202 unsigned long flags;
3203 struct slgt_info *info = container_of(port, struct slgt_info, port);
3204
3205 spin_lock_irqsave(&info->lock,flags);
3206 get_signals(info);
3207 spin_unlock_irqrestore(&info->lock,flags);
3208 return (info->signals & SerialSignal_DCD) ? 1 : 0;
3209 }
3210
dtr_rts(struct tty_port * port,int on)3211 static void dtr_rts(struct tty_port *port, int on)
3212 {
3213 unsigned long flags;
3214 struct slgt_info *info = container_of(port, struct slgt_info, port);
3215
3216 spin_lock_irqsave(&info->lock,flags);
3217 if (on)
3218 info->signals |= SerialSignal_RTS | SerialSignal_DTR;
3219 else
3220 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
3221 set_signals(info);
3222 spin_unlock_irqrestore(&info->lock,flags);
3223 }
3224
3225
3226 /*
3227 * block current process until the device is ready to open
3228 */
block_til_ready(struct tty_struct * tty,struct file * filp,struct slgt_info * info)3229 static int block_til_ready(struct tty_struct *tty, struct file *filp,
3230 struct slgt_info *info)
3231 {
3232 DECLARE_WAITQUEUE(wait, current);
3233 int retval;
3234 bool do_clocal = false;
3235 unsigned long flags;
3236 int cd;
3237 struct tty_port *port = &info->port;
3238
3239 DBGINFO(("%s block_til_ready\n", tty->driver->name));
3240
3241 if (filp->f_flags & O_NONBLOCK || tty_io_error(tty)) {
3242 /* nonblock mode is set or port is not enabled */
3243 tty_port_set_active(port, 1);
3244 return 0;
3245 }
3246
3247 if (C_CLOCAL(tty))
3248 do_clocal = true;
3249
3250 /* Wait for carrier detect and the line to become
3251 * free (i.e., not in use by the callout). While we are in
3252 * this loop, port->count is dropped by one, so that
3253 * close() knows when to free things. We restore it upon
3254 * exit, either normal or abnormal.
3255 */
3256
3257 retval = 0;
3258 add_wait_queue(&port->open_wait, &wait);
3259
3260 spin_lock_irqsave(&info->lock, flags);
3261 port->count--;
3262 spin_unlock_irqrestore(&info->lock, flags);
3263 port->blocked_open++;
3264
3265 while (1) {
3266 if (C_BAUD(tty) && tty_port_initialized(port))
3267 tty_port_raise_dtr_rts(port);
3268
3269 set_current_state(TASK_INTERRUPTIBLE);
3270
3271 if (tty_hung_up_p(filp) || !tty_port_initialized(port)) {
3272 retval = (port->flags & ASYNC_HUP_NOTIFY) ?
3273 -EAGAIN : -ERESTARTSYS;
3274 break;
3275 }
3276
3277 cd = tty_port_carrier_raised(port);
3278 if (do_clocal || cd)
3279 break;
3280
3281 if (signal_pending(current)) {
3282 retval = -ERESTARTSYS;
3283 break;
3284 }
3285
3286 DBGINFO(("%s block_til_ready wait\n", tty->driver->name));
3287 tty_unlock(tty);
3288 schedule();
3289 tty_lock(tty);
3290 }
3291
3292 set_current_state(TASK_RUNNING);
3293 remove_wait_queue(&port->open_wait, &wait);
3294
3295 if (!tty_hung_up_p(filp))
3296 port->count++;
3297 port->blocked_open--;
3298
3299 if (!retval)
3300 tty_port_set_active(port, 1);
3301
3302 DBGINFO(("%s block_til_ready ready, rc=%d\n", tty->driver->name, retval));
3303 return retval;
3304 }
3305
3306 /*
3307 * allocate buffers used for calling line discipline receive_buf
3308 * directly in synchronous mode
3309 * note: add 5 bytes to max frame size to allow appending
3310 * 32-bit CRC and status byte when configured to do so
3311 */
alloc_tmp_rbuf(struct slgt_info * info)3312 static int alloc_tmp_rbuf(struct slgt_info *info)
3313 {
3314 info->tmp_rbuf = kmalloc(info->max_frame_size + 5, GFP_KERNEL);
3315 if (info->tmp_rbuf == NULL)
3316 return -ENOMEM;
3317 /* unused flag buffer to satisfy receive_buf calling interface */
3318 info->flag_buf = kzalloc(info->max_frame_size + 5, GFP_KERNEL);
3319 if (!info->flag_buf) {
3320 kfree(info->tmp_rbuf);
3321 info->tmp_rbuf = NULL;
3322 return -ENOMEM;
3323 }
3324 return 0;
3325 }
3326
free_tmp_rbuf(struct slgt_info * info)3327 static void free_tmp_rbuf(struct slgt_info *info)
3328 {
3329 kfree(info->tmp_rbuf);
3330 info->tmp_rbuf = NULL;
3331 kfree(info->flag_buf);
3332 info->flag_buf = NULL;
3333 }
3334
3335 /*
3336 * allocate DMA descriptor lists.
3337 */
alloc_desc(struct slgt_info * info)3338 static int alloc_desc(struct slgt_info *info)
3339 {
3340 unsigned int i;
3341 unsigned int pbufs;
3342
3343 /* allocate memory to hold descriptor lists */
3344 info->bufs = pci_zalloc_consistent(info->pdev, DESC_LIST_SIZE,
3345 &info->bufs_dma_addr);
3346 if (info->bufs == NULL)
3347 return -ENOMEM;
3348
3349 info->rbufs = (struct slgt_desc*)info->bufs;
3350 info->tbufs = ((struct slgt_desc*)info->bufs) + info->rbuf_count;
3351
3352 pbufs = (unsigned int)info->bufs_dma_addr;
3353
3354 /*
3355 * Build circular lists of descriptors
3356 */
3357
3358 for (i=0; i < info->rbuf_count; i++) {
3359 /* physical address of this descriptor */
3360 info->rbufs[i].pdesc = pbufs + (i * sizeof(struct slgt_desc));
3361
3362 /* physical address of next descriptor */
3363 if (i == info->rbuf_count - 1)
3364 info->rbufs[i].next = cpu_to_le32(pbufs);
3365 else
3366 info->rbufs[i].next = cpu_to_le32(pbufs + ((i+1) * sizeof(struct slgt_desc)));
3367 set_desc_count(info->rbufs[i], DMABUFSIZE);
3368 }
3369
3370 for (i=0; i < info->tbuf_count; i++) {
3371 /* physical address of this descriptor */
3372 info->tbufs[i].pdesc = pbufs + ((info->rbuf_count + i) * sizeof(struct slgt_desc));
3373
3374 /* physical address of next descriptor */
3375 if (i == info->tbuf_count - 1)
3376 info->tbufs[i].next = cpu_to_le32(pbufs + info->rbuf_count * sizeof(struct slgt_desc));
3377 else
3378 info->tbufs[i].next = cpu_to_le32(pbufs + ((info->rbuf_count + i + 1) * sizeof(struct slgt_desc)));
3379 }
3380
3381 return 0;
3382 }
3383
free_desc(struct slgt_info * info)3384 static void free_desc(struct slgt_info *info)
3385 {
3386 if (info->bufs != NULL) {
3387 pci_free_consistent(info->pdev, DESC_LIST_SIZE, info->bufs, info->bufs_dma_addr);
3388 info->bufs = NULL;
3389 info->rbufs = NULL;
3390 info->tbufs = NULL;
3391 }
3392 }
3393
alloc_bufs(struct slgt_info * info,struct slgt_desc * bufs,int count)3394 static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3395 {
3396 int i;
3397 for (i=0; i < count; i++) {
3398 if ((bufs[i].buf = pci_alloc_consistent(info->pdev, DMABUFSIZE, &bufs[i].buf_dma_addr)) == NULL)
3399 return -ENOMEM;
3400 bufs[i].pbuf = cpu_to_le32((unsigned int)bufs[i].buf_dma_addr);
3401 }
3402 return 0;
3403 }
3404
free_bufs(struct slgt_info * info,struct slgt_desc * bufs,int count)3405 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3406 {
3407 int i;
3408 for (i=0; i < count; i++) {
3409 if (bufs[i].buf == NULL)
3410 continue;
3411 pci_free_consistent(info->pdev, DMABUFSIZE, bufs[i].buf, bufs[i].buf_dma_addr);
3412 bufs[i].buf = NULL;
3413 }
3414 }
3415
alloc_dma_bufs(struct slgt_info * info)3416 static int alloc_dma_bufs(struct slgt_info *info)
3417 {
3418 info->rbuf_count = 32;
3419 info->tbuf_count = 32;
3420
3421 if (alloc_desc(info) < 0 ||
3422 alloc_bufs(info, info->rbufs, info->rbuf_count) < 0 ||
3423 alloc_bufs(info, info->tbufs, info->tbuf_count) < 0 ||
3424 alloc_tmp_rbuf(info) < 0) {
3425 DBGERR(("%s DMA buffer alloc fail\n", info->device_name));
3426 return -ENOMEM;
3427 }
3428 reset_rbufs(info);
3429 return 0;
3430 }
3431
free_dma_bufs(struct slgt_info * info)3432 static void free_dma_bufs(struct slgt_info *info)
3433 {
3434 if (info->bufs) {
3435 free_bufs(info, info->rbufs, info->rbuf_count);
3436 free_bufs(info, info->tbufs, info->tbuf_count);
3437 free_desc(info);
3438 }
3439 free_tmp_rbuf(info);
3440 }
3441
claim_resources(struct slgt_info * info)3442 static int claim_resources(struct slgt_info *info)
3443 {
3444 if (request_mem_region(info->phys_reg_addr, SLGT_REG_SIZE, "synclink_gt") == NULL) {
3445 DBGERR(("%s reg addr conflict, addr=%08X\n",
3446 info->device_name, info->phys_reg_addr));
3447 info->init_error = DiagStatus_AddressConflict;
3448 goto errout;
3449 }
3450 else
3451 info->reg_addr_requested = true;
3452
3453 info->reg_addr = ioremap_nocache(info->phys_reg_addr, SLGT_REG_SIZE);
3454 if (!info->reg_addr) {
3455 DBGERR(("%s can't map device registers, addr=%08X\n",
3456 info->device_name, info->phys_reg_addr));
3457 info->init_error = DiagStatus_CantAssignPciResources;
3458 goto errout;
3459 }
3460 return 0;
3461
3462 errout:
3463 release_resources(info);
3464 return -ENODEV;
3465 }
3466
release_resources(struct slgt_info * info)3467 static void release_resources(struct slgt_info *info)
3468 {
3469 if (info->irq_requested) {
3470 free_irq(info->irq_level, info);
3471 info->irq_requested = false;
3472 }
3473
3474 if (info->reg_addr_requested) {
3475 release_mem_region(info->phys_reg_addr, SLGT_REG_SIZE);
3476 info->reg_addr_requested = false;
3477 }
3478
3479 if (info->reg_addr) {
3480 iounmap(info->reg_addr);
3481 info->reg_addr = NULL;
3482 }
3483 }
3484
3485 /* Add the specified device instance data structure to the
3486 * global linked list of devices and increment the device count.
3487 */
add_device(struct slgt_info * info)3488 static void add_device(struct slgt_info *info)
3489 {
3490 char *devstr;
3491
3492 info->next_device = NULL;
3493 info->line = slgt_device_count;
3494 sprintf(info->device_name, "%s%d", tty_dev_prefix, info->line);
3495
3496 if (info->line < MAX_DEVICES) {
3497 if (maxframe[info->line])
3498 info->max_frame_size = maxframe[info->line];
3499 }
3500
3501 slgt_device_count++;
3502
3503 if (!slgt_device_list)
3504 slgt_device_list = info;
3505 else {
3506 struct slgt_info *current_dev = slgt_device_list;
3507 while(current_dev->next_device)
3508 current_dev = current_dev->next_device;
3509 current_dev->next_device = info;
3510 }
3511
3512 if (info->max_frame_size < 4096)
3513 info->max_frame_size = 4096;
3514 else if (info->max_frame_size > 65535)
3515 info->max_frame_size = 65535;
3516
3517 switch(info->pdev->device) {
3518 case SYNCLINK_GT_DEVICE_ID:
3519 devstr = "GT";
3520 break;
3521 case SYNCLINK_GT2_DEVICE_ID:
3522 devstr = "GT2";
3523 break;
3524 case SYNCLINK_GT4_DEVICE_ID:
3525 devstr = "GT4";
3526 break;
3527 case SYNCLINK_AC_DEVICE_ID:
3528 devstr = "AC";
3529 info->params.mode = MGSL_MODE_ASYNC;
3530 break;
3531 default:
3532 devstr = "(unknown model)";
3533 }
3534 printk("SyncLink %s %s IO=%08x IRQ=%d MaxFrameSize=%u\n",
3535 devstr, info->device_name, info->phys_reg_addr,
3536 info->irq_level, info->max_frame_size);
3537
3538 #if SYNCLINK_GENERIC_HDLC
3539 hdlcdev_init(info);
3540 #endif
3541 }
3542
3543 static const struct tty_port_operations slgt_port_ops = {
3544 .carrier_raised = carrier_raised,
3545 .dtr_rts = dtr_rts,
3546 };
3547
3548 /*
3549 * allocate device instance structure, return NULL on failure
3550 */
alloc_dev(int adapter_num,int port_num,struct pci_dev * pdev)3551 static struct slgt_info *alloc_dev(int adapter_num, int port_num, struct pci_dev *pdev)
3552 {
3553 struct slgt_info *info;
3554
3555 info = kzalloc(sizeof(struct slgt_info), GFP_KERNEL);
3556
3557 if (!info) {
3558 DBGERR(("%s device alloc failed adapter=%d port=%d\n",
3559 driver_name, adapter_num, port_num));
3560 } else {
3561 tty_port_init(&info->port);
3562 info->port.ops = &slgt_port_ops;
3563 info->magic = MGSL_MAGIC;
3564 INIT_WORK(&info->task, bh_handler);
3565 info->max_frame_size = 4096;
3566 info->base_clock = 14745600;
3567 info->rbuf_fill_level = DMABUFSIZE;
3568 info->port.close_delay = 5*HZ/10;
3569 info->port.closing_wait = 30*HZ;
3570 init_waitqueue_head(&info->status_event_wait_q);
3571 init_waitqueue_head(&info->event_wait_q);
3572 spin_lock_init(&info->netlock);
3573 memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS));
3574 info->idle_mode = HDLC_TXIDLE_FLAGS;
3575 info->adapter_num = adapter_num;
3576 info->port_num = port_num;
3577
3578 timer_setup(&info->tx_timer, tx_timeout, 0);
3579 timer_setup(&info->rx_timer, rx_timeout, 0);
3580
3581 /* Copy configuration info to device instance data */
3582 info->pdev = pdev;
3583 info->irq_level = pdev->irq;
3584 info->phys_reg_addr = pci_resource_start(pdev,0);
3585
3586 info->bus_type = MGSL_BUS_TYPE_PCI;
3587 info->irq_flags = IRQF_SHARED;
3588
3589 info->init_error = -1; /* assume error, set to 0 on successful init */
3590 }
3591
3592 return info;
3593 }
3594
device_init(int adapter_num,struct pci_dev * pdev)3595 static void device_init(int adapter_num, struct pci_dev *pdev)
3596 {
3597 struct slgt_info *port_array[SLGT_MAX_PORTS];
3598 int i;
3599 int port_count = 1;
3600
3601 if (pdev->device == SYNCLINK_GT2_DEVICE_ID)
3602 port_count = 2;
3603 else if (pdev->device == SYNCLINK_GT4_DEVICE_ID)
3604 port_count = 4;
3605
3606 /* allocate device instances for all ports */
3607 for (i=0; i < port_count; ++i) {
3608 port_array[i] = alloc_dev(adapter_num, i, pdev);
3609 if (port_array[i] == NULL) {
3610 for (--i; i >= 0; --i) {
3611 tty_port_destroy(&port_array[i]->port);
3612 kfree(port_array[i]);
3613 }
3614 return;
3615 }
3616 }
3617
3618 /* give copy of port_array to all ports and add to device list */
3619 for (i=0; i < port_count; ++i) {
3620 memcpy(port_array[i]->port_array, port_array, sizeof(port_array));
3621 add_device(port_array[i]);
3622 port_array[i]->port_count = port_count;
3623 spin_lock_init(&port_array[i]->lock);
3624 }
3625
3626 /* Allocate and claim adapter resources */
3627 if (!claim_resources(port_array[0])) {
3628
3629 alloc_dma_bufs(port_array[0]);
3630
3631 /* copy resource information from first port to others */
3632 for (i = 1; i < port_count; ++i) {
3633 port_array[i]->irq_level = port_array[0]->irq_level;
3634 port_array[i]->reg_addr = port_array[0]->reg_addr;
3635 alloc_dma_bufs(port_array[i]);
3636 }
3637
3638 if (request_irq(port_array[0]->irq_level,
3639 slgt_interrupt,
3640 port_array[0]->irq_flags,
3641 port_array[0]->device_name,
3642 port_array[0]) < 0) {
3643 DBGERR(("%s request_irq failed IRQ=%d\n",
3644 port_array[0]->device_name,
3645 port_array[0]->irq_level));
3646 } else {
3647 port_array[0]->irq_requested = true;
3648 adapter_test(port_array[0]);
3649 for (i=1 ; i < port_count ; i++) {
3650 port_array[i]->init_error = port_array[0]->init_error;
3651 port_array[i]->gpio_present = port_array[0]->gpio_present;
3652 }
3653 }
3654 }
3655
3656 for (i = 0; i < port_count; ++i) {
3657 struct slgt_info *info = port_array[i];
3658 tty_port_register_device(&info->port, serial_driver, info->line,
3659 &info->pdev->dev);
3660 }
3661 }
3662
init_one(struct pci_dev * dev,const struct pci_device_id * ent)3663 static int init_one(struct pci_dev *dev,
3664 const struct pci_device_id *ent)
3665 {
3666 if (pci_enable_device(dev)) {
3667 printk("error enabling pci device %p\n", dev);
3668 return -EIO;
3669 }
3670 pci_set_master(dev);
3671 device_init(slgt_device_count, dev);
3672 return 0;
3673 }
3674
remove_one(struct pci_dev * dev)3675 static void remove_one(struct pci_dev *dev)
3676 {
3677 }
3678
3679 static const struct tty_operations ops = {
3680 .open = open,
3681 .close = close,
3682 .write = write,
3683 .put_char = put_char,
3684 .flush_chars = flush_chars,
3685 .write_room = write_room,
3686 .chars_in_buffer = chars_in_buffer,
3687 .flush_buffer = flush_buffer,
3688 .ioctl = ioctl,
3689 .compat_ioctl = slgt_compat_ioctl,
3690 .throttle = throttle,
3691 .unthrottle = unthrottle,
3692 .send_xchar = send_xchar,
3693 .break_ctl = set_break,
3694 .wait_until_sent = wait_until_sent,
3695 .set_termios = set_termios,
3696 .stop = tx_hold,
3697 .start = tx_release,
3698 .hangup = hangup,
3699 .tiocmget = tiocmget,
3700 .tiocmset = tiocmset,
3701 .get_icount = get_icount,
3702 .proc_show = synclink_gt_proc_show,
3703 };
3704
slgt_cleanup(void)3705 static void slgt_cleanup(void)
3706 {
3707 int rc;
3708 struct slgt_info *info;
3709 struct slgt_info *tmp;
3710
3711 printk(KERN_INFO "unload %s\n", driver_name);
3712
3713 if (serial_driver) {
3714 for (info=slgt_device_list ; info != NULL ; info=info->next_device)
3715 tty_unregister_device(serial_driver, info->line);
3716 rc = tty_unregister_driver(serial_driver);
3717 if (rc)
3718 DBGERR(("tty_unregister_driver error=%d\n", rc));
3719 put_tty_driver(serial_driver);
3720 }
3721
3722 /* reset devices */
3723 info = slgt_device_list;
3724 while(info) {
3725 reset_port(info);
3726 info = info->next_device;
3727 }
3728
3729 /* release devices */
3730 info = slgt_device_list;
3731 while(info) {
3732 #if SYNCLINK_GENERIC_HDLC
3733 hdlcdev_exit(info);
3734 #endif
3735 free_dma_bufs(info);
3736 free_tmp_rbuf(info);
3737 if (info->port_num == 0)
3738 release_resources(info);
3739 tmp = info;
3740 info = info->next_device;
3741 tty_port_destroy(&tmp->port);
3742 kfree(tmp);
3743 }
3744
3745 if (pci_registered)
3746 pci_unregister_driver(&pci_driver);
3747 }
3748
3749 /*
3750 * Driver initialization entry point.
3751 */
slgt_init(void)3752 static int __init slgt_init(void)
3753 {
3754 int rc;
3755
3756 printk(KERN_INFO "%s\n", driver_name);
3757
3758 serial_driver = alloc_tty_driver(MAX_DEVICES);
3759 if (!serial_driver) {
3760 printk("%s can't allocate tty driver\n", driver_name);
3761 return -ENOMEM;
3762 }
3763
3764 /* Initialize the tty_driver structure */
3765
3766 serial_driver->driver_name = slgt_driver_name;
3767 serial_driver->name = tty_dev_prefix;
3768 serial_driver->major = ttymajor;
3769 serial_driver->minor_start = 64;
3770 serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
3771 serial_driver->subtype = SERIAL_TYPE_NORMAL;
3772 serial_driver->init_termios = tty_std_termios;
3773 serial_driver->init_termios.c_cflag =
3774 B9600 | CS8 | CREAD | HUPCL | CLOCAL;
3775 serial_driver->init_termios.c_ispeed = 9600;
3776 serial_driver->init_termios.c_ospeed = 9600;
3777 serial_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
3778 tty_set_operations(serial_driver, &ops);
3779 if ((rc = tty_register_driver(serial_driver)) < 0) {
3780 DBGERR(("%s can't register serial driver\n", driver_name));
3781 put_tty_driver(serial_driver);
3782 serial_driver = NULL;
3783 goto error;
3784 }
3785
3786 printk(KERN_INFO "%s, tty major#%d\n",
3787 driver_name, serial_driver->major);
3788
3789 slgt_device_count = 0;
3790 if ((rc = pci_register_driver(&pci_driver)) < 0) {
3791 printk("%s pci_register_driver error=%d\n", driver_name, rc);
3792 goto error;
3793 }
3794 pci_registered = true;
3795
3796 if (!slgt_device_list)
3797 printk("%s no devices found\n",driver_name);
3798
3799 return 0;
3800
3801 error:
3802 slgt_cleanup();
3803 return rc;
3804 }
3805
slgt_exit(void)3806 static void __exit slgt_exit(void)
3807 {
3808 slgt_cleanup();
3809 }
3810
3811 module_init(slgt_init);
3812 module_exit(slgt_exit);
3813
3814 /*
3815 * register access routines
3816 */
3817
3818 #define CALC_REGADDR() \
3819 unsigned long reg_addr = ((unsigned long)info->reg_addr) + addr; \
3820 if (addr >= 0x80) \
3821 reg_addr += (info->port_num) * 32; \
3822 else if (addr >= 0x40) \
3823 reg_addr += (info->port_num) * 16;
3824
rd_reg8(struct slgt_info * info,unsigned int addr)3825 static __u8 rd_reg8(struct slgt_info *info, unsigned int addr)
3826 {
3827 CALC_REGADDR();
3828 return readb((void __iomem *)reg_addr);
3829 }
3830
wr_reg8(struct slgt_info * info,unsigned int addr,__u8 value)3831 static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value)
3832 {
3833 CALC_REGADDR();
3834 writeb(value, (void __iomem *)reg_addr);
3835 }
3836
rd_reg16(struct slgt_info * info,unsigned int addr)3837 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr)
3838 {
3839 CALC_REGADDR();
3840 return readw((void __iomem *)reg_addr);
3841 }
3842
wr_reg16(struct slgt_info * info,unsigned int addr,__u16 value)3843 static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value)
3844 {
3845 CALC_REGADDR();
3846 writew(value, (void __iomem *)reg_addr);
3847 }
3848
rd_reg32(struct slgt_info * info,unsigned int addr)3849 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr)
3850 {
3851 CALC_REGADDR();
3852 return readl((void __iomem *)reg_addr);
3853 }
3854
wr_reg32(struct slgt_info * info,unsigned int addr,__u32 value)3855 static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value)
3856 {
3857 CALC_REGADDR();
3858 writel(value, (void __iomem *)reg_addr);
3859 }
3860
rdma_reset(struct slgt_info * info)3861 static void rdma_reset(struct slgt_info *info)
3862 {
3863 unsigned int i;
3864
3865 /* set reset bit */
3866 wr_reg32(info, RDCSR, BIT1);
3867
3868 /* wait for enable bit cleared */
3869 for(i=0 ; i < 1000 ; i++)
3870 if (!(rd_reg32(info, RDCSR) & BIT0))
3871 break;
3872 }
3873
tdma_reset(struct slgt_info * info)3874 static void tdma_reset(struct slgt_info *info)
3875 {
3876 unsigned int i;
3877
3878 /* set reset bit */
3879 wr_reg32(info, TDCSR, BIT1);
3880
3881 /* wait for enable bit cleared */
3882 for(i=0 ; i < 1000 ; i++)
3883 if (!(rd_reg32(info, TDCSR) & BIT0))
3884 break;
3885 }
3886
3887 /*
3888 * enable internal loopback
3889 * TxCLK and RxCLK are generated from BRG
3890 * and TxD is looped back to RxD internally.
3891 */
enable_loopback(struct slgt_info * info)3892 static void enable_loopback(struct slgt_info *info)
3893 {
3894 /* SCR (serial control) BIT2=loopback enable */
3895 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT2));
3896
3897 if (info->params.mode != MGSL_MODE_ASYNC) {
3898 /* CCR (clock control)
3899 * 07..05 tx clock source (010 = BRG)
3900 * 04..02 rx clock source (010 = BRG)
3901 * 01 auxclk enable (0 = disable)
3902 * 00 BRG enable (1 = enable)
3903 *
3904 * 0100 1001
3905 */
3906 wr_reg8(info, CCR, 0x49);
3907
3908 /* set speed if available, otherwise use default */
3909 if (info->params.clock_speed)
3910 set_rate(info, info->params.clock_speed);
3911 else
3912 set_rate(info, 3686400);
3913 }
3914 }
3915
3916 /*
3917 * set baud rate generator to specified rate
3918 */
set_rate(struct slgt_info * info,u32 rate)3919 static void set_rate(struct slgt_info *info, u32 rate)
3920 {
3921 unsigned int div;
3922 unsigned int osc = info->base_clock;
3923
3924 /* div = osc/rate - 1
3925 *
3926 * Round div up if osc/rate is not integer to
3927 * force to next slowest rate.
3928 */
3929
3930 if (rate) {
3931 div = osc/rate;
3932 if (!(osc % rate) && div)
3933 div--;
3934 wr_reg16(info, BDR, (unsigned short)div);
3935 }
3936 }
3937
rx_stop(struct slgt_info * info)3938 static void rx_stop(struct slgt_info *info)
3939 {
3940 unsigned short val;
3941
3942 /* disable and reset receiver */
3943 val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */
3944 wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3945 wr_reg16(info, RCR, val); /* clear reset bit */
3946
3947 slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA + IRQ_RXIDLE);
3948
3949 /* clear pending rx interrupts */
3950 wr_reg16(info, SSR, IRQ_RXIDLE + IRQ_RXOVER);
3951
3952 rdma_reset(info);
3953
3954 info->rx_enabled = false;
3955 info->rx_restart = false;
3956 }
3957
rx_start(struct slgt_info * info)3958 static void rx_start(struct slgt_info *info)
3959 {
3960 unsigned short val;
3961
3962 slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA);
3963
3964 /* clear pending rx overrun IRQ */
3965 wr_reg16(info, SSR, IRQ_RXOVER);
3966
3967 /* reset and disable receiver */
3968 val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */
3969 wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3970 wr_reg16(info, RCR, val); /* clear reset bit */
3971
3972 rdma_reset(info);
3973 reset_rbufs(info);
3974
3975 if (info->rx_pio) {
3976 /* rx request when rx FIFO not empty */
3977 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) & ~BIT14));
3978 slgt_irq_on(info, IRQ_RXDATA);
3979 if (info->params.mode == MGSL_MODE_ASYNC) {
3980 /* enable saving of rx status */
3981 wr_reg32(info, RDCSR, BIT6);
3982 }
3983 } else {
3984 /* rx request when rx FIFO half full */
3985 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT14));
3986 /* set 1st descriptor address */
3987 wr_reg32(info, RDDAR, info->rbufs[0].pdesc);
3988
3989 if (info->params.mode != MGSL_MODE_ASYNC) {
3990 /* enable rx DMA and DMA interrupt */
3991 wr_reg32(info, RDCSR, (BIT2 + BIT0));
3992 } else {
3993 /* enable saving of rx status, rx DMA and DMA interrupt */
3994 wr_reg32(info, RDCSR, (BIT6 + BIT2 + BIT0));
3995 }
3996 }
3997
3998 slgt_irq_on(info, IRQ_RXOVER);
3999
4000 /* enable receiver */
4001 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | BIT1));
4002
4003 info->rx_restart = false;
4004 info->rx_enabled = true;
4005 }
4006
tx_start(struct slgt_info * info)4007 static void tx_start(struct slgt_info *info)
4008 {
4009 if (!info->tx_enabled) {
4010 wr_reg16(info, TCR,
4011 (unsigned short)((rd_reg16(info, TCR) | BIT1) & ~BIT2));
4012 info->tx_enabled = true;
4013 }
4014
4015 if (desc_count(info->tbufs[info->tbuf_start])) {
4016 info->drop_rts_on_tx_done = false;
4017
4018 if (info->params.mode != MGSL_MODE_ASYNC) {
4019 if (info->params.flags & HDLC_FLAG_AUTO_RTS) {
4020 get_signals(info);
4021 if (!(info->signals & SerialSignal_RTS)) {
4022 info->signals |= SerialSignal_RTS;
4023 set_signals(info);
4024 info->drop_rts_on_tx_done = true;
4025 }
4026 }
4027
4028 slgt_irq_off(info, IRQ_TXDATA);
4029 slgt_irq_on(info, IRQ_TXUNDER + IRQ_TXIDLE);
4030 /* clear tx idle and underrun status bits */
4031 wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
4032 } else {
4033 slgt_irq_off(info, IRQ_TXDATA);
4034 slgt_irq_on(info, IRQ_TXIDLE);
4035 /* clear tx idle status bit */
4036 wr_reg16(info, SSR, IRQ_TXIDLE);
4037 }
4038 /* set 1st descriptor address and start DMA */
4039 wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
4040 wr_reg32(info, TDCSR, BIT2 + BIT0);
4041 info->tx_active = true;
4042 }
4043 }
4044
tx_stop(struct slgt_info * info)4045 static void tx_stop(struct slgt_info *info)
4046 {
4047 unsigned short val;
4048
4049 del_timer(&info->tx_timer);
4050
4051 tdma_reset(info);
4052
4053 /* reset and disable transmitter */
4054 val = rd_reg16(info, TCR) & ~BIT1; /* clear enable bit */
4055 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
4056
4057 slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
4058
4059 /* clear tx idle and underrun status bit */
4060 wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
4061
4062 reset_tbufs(info);
4063
4064 info->tx_enabled = false;
4065 info->tx_active = false;
4066 }
4067
reset_port(struct slgt_info * info)4068 static void reset_port(struct slgt_info *info)
4069 {
4070 if (!info->reg_addr)
4071 return;
4072
4073 tx_stop(info);
4074 rx_stop(info);
4075
4076 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
4077 set_signals(info);
4078
4079 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4080 }
4081
reset_adapter(struct slgt_info * info)4082 static void reset_adapter(struct slgt_info *info)
4083 {
4084 int i;
4085 for (i=0; i < info->port_count; ++i) {
4086 if (info->port_array[i])
4087 reset_port(info->port_array[i]);
4088 }
4089 }
4090
async_mode(struct slgt_info * info)4091 static void async_mode(struct slgt_info *info)
4092 {
4093 unsigned short val;
4094
4095 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4096 tx_stop(info);
4097 rx_stop(info);
4098
4099 /* TCR (tx control)
4100 *
4101 * 15..13 mode, 010=async
4102 * 12..10 encoding, 000=NRZ
4103 * 09 parity enable
4104 * 08 1=odd parity, 0=even parity
4105 * 07 1=RTS driver control
4106 * 06 1=break enable
4107 * 05..04 character length
4108 * 00=5 bits
4109 * 01=6 bits
4110 * 10=7 bits
4111 * 11=8 bits
4112 * 03 0=1 stop bit, 1=2 stop bits
4113 * 02 reset
4114 * 01 enable
4115 * 00 auto-CTS enable
4116 */
4117 val = 0x4000;
4118
4119 if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4120 val |= BIT7;
4121
4122 if (info->params.parity != ASYNC_PARITY_NONE) {
4123 val |= BIT9;
4124 if (info->params.parity == ASYNC_PARITY_ODD)
4125 val |= BIT8;
4126 }
4127
4128 switch (info->params.data_bits)
4129 {
4130 case 6: val |= BIT4; break;
4131 case 7: val |= BIT5; break;
4132 case 8: val |= BIT5 + BIT4; break;
4133 }
4134
4135 if (info->params.stop_bits != 1)
4136 val |= BIT3;
4137
4138 if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4139 val |= BIT0;
4140
4141 wr_reg16(info, TCR, val);
4142
4143 /* RCR (rx control)
4144 *
4145 * 15..13 mode, 010=async
4146 * 12..10 encoding, 000=NRZ
4147 * 09 parity enable
4148 * 08 1=odd parity, 0=even parity
4149 * 07..06 reserved, must be 0
4150 * 05..04 character length
4151 * 00=5 bits
4152 * 01=6 bits
4153 * 10=7 bits
4154 * 11=8 bits
4155 * 03 reserved, must be zero
4156 * 02 reset
4157 * 01 enable
4158 * 00 auto-DCD enable
4159 */
4160 val = 0x4000;
4161
4162 if (info->params.parity != ASYNC_PARITY_NONE) {
4163 val |= BIT9;
4164 if (info->params.parity == ASYNC_PARITY_ODD)
4165 val |= BIT8;
4166 }
4167
4168 switch (info->params.data_bits)
4169 {
4170 case 6: val |= BIT4; break;
4171 case 7: val |= BIT5; break;
4172 case 8: val |= BIT5 + BIT4; break;
4173 }
4174
4175 if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4176 val |= BIT0;
4177
4178 wr_reg16(info, RCR, val);
4179
4180 /* CCR (clock control)
4181 *
4182 * 07..05 011 = tx clock source is BRG/16
4183 * 04..02 010 = rx clock source is BRG
4184 * 01 0 = auxclk disabled
4185 * 00 1 = BRG enabled
4186 *
4187 * 0110 1001
4188 */
4189 wr_reg8(info, CCR, 0x69);
4190
4191 msc_set_vcr(info);
4192
4193 /* SCR (serial control)
4194 *
4195 * 15 1=tx req on FIFO half empty
4196 * 14 1=rx req on FIFO half full
4197 * 13 tx data IRQ enable
4198 * 12 tx idle IRQ enable
4199 * 11 rx break on IRQ enable
4200 * 10 rx data IRQ enable
4201 * 09 rx break off IRQ enable
4202 * 08 overrun IRQ enable
4203 * 07 DSR IRQ enable
4204 * 06 CTS IRQ enable
4205 * 05 DCD IRQ enable
4206 * 04 RI IRQ enable
4207 * 03 0=16x sampling, 1=8x sampling
4208 * 02 1=txd->rxd internal loopback enable
4209 * 01 reserved, must be zero
4210 * 00 1=master IRQ enable
4211 */
4212 val = BIT15 + BIT14 + BIT0;
4213 /* JCR[8] : 1 = x8 async mode feature available */
4214 if ((rd_reg32(info, JCR) & BIT8) && info->params.data_rate &&
4215 ((info->base_clock < (info->params.data_rate * 16)) ||
4216 (info->base_clock % (info->params.data_rate * 16)))) {
4217 /* use 8x sampling */
4218 val |= BIT3;
4219 set_rate(info, info->params.data_rate * 8);
4220 } else {
4221 /* use 16x sampling */
4222 set_rate(info, info->params.data_rate * 16);
4223 }
4224 wr_reg16(info, SCR, val);
4225
4226 slgt_irq_on(info, IRQ_RXBREAK | IRQ_RXOVER);
4227
4228 if (info->params.loopback)
4229 enable_loopback(info);
4230 }
4231
sync_mode(struct slgt_info * info)4232 static void sync_mode(struct slgt_info *info)
4233 {
4234 unsigned short val;
4235
4236 slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4237 tx_stop(info);
4238 rx_stop(info);
4239
4240 /* TCR (tx control)
4241 *
4242 * 15..13 mode
4243 * 000=HDLC/SDLC
4244 * 001=raw bit synchronous
4245 * 010=asynchronous/isochronous
4246 * 011=monosync byte synchronous
4247 * 100=bisync byte synchronous
4248 * 101=xsync byte synchronous
4249 * 12..10 encoding
4250 * 09 CRC enable
4251 * 08 CRC32
4252 * 07 1=RTS driver control
4253 * 06 preamble enable
4254 * 05..04 preamble length
4255 * 03 share open/close flag
4256 * 02 reset
4257 * 01 enable
4258 * 00 auto-CTS enable
4259 */
4260 val = BIT2;
4261
4262 switch(info->params.mode) {
4263 case MGSL_MODE_XSYNC:
4264 val |= BIT15 + BIT13;
4265 break;
4266 case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4267 case MGSL_MODE_BISYNC: val |= BIT15; break;
4268 case MGSL_MODE_RAW: val |= BIT13; break;
4269 }
4270 if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4271 val |= BIT7;
4272
4273 switch(info->params.encoding)
4274 {
4275 case HDLC_ENCODING_NRZB: val |= BIT10; break;
4276 case HDLC_ENCODING_NRZI_MARK: val |= BIT11; break;
4277 case HDLC_ENCODING_NRZI: val |= BIT11 + BIT10; break;
4278 case HDLC_ENCODING_BIPHASE_MARK: val |= BIT12; break;
4279 case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4280 case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4281 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4282 }
4283
4284 switch (info->params.crc_type & HDLC_CRC_MASK)
4285 {
4286 case HDLC_CRC_16_CCITT: val |= BIT9; break;
4287 case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4288 }
4289
4290 if (info->params.preamble != HDLC_PREAMBLE_PATTERN_NONE)
4291 val |= BIT6;
4292
4293 switch (info->params.preamble_length)
4294 {
4295 case HDLC_PREAMBLE_LENGTH_16BITS: val |= BIT5; break;
4296 case HDLC_PREAMBLE_LENGTH_32BITS: val |= BIT4; break;
4297 case HDLC_PREAMBLE_LENGTH_64BITS: val |= BIT5 + BIT4; break;
4298 }
4299
4300 if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4301 val |= BIT0;
4302
4303 wr_reg16(info, TCR, val);
4304
4305 /* TPR (transmit preamble) */
4306
4307 switch (info->params.preamble)
4308 {
4309 case HDLC_PREAMBLE_PATTERN_FLAGS: val = 0x7e; break;
4310 case HDLC_PREAMBLE_PATTERN_ONES: val = 0xff; break;
4311 case HDLC_PREAMBLE_PATTERN_ZEROS: val = 0x00; break;
4312 case HDLC_PREAMBLE_PATTERN_10: val = 0x55; break;
4313 case HDLC_PREAMBLE_PATTERN_01: val = 0xaa; break;
4314 default: val = 0x7e; break;
4315 }
4316 wr_reg8(info, TPR, (unsigned char)val);
4317
4318 /* RCR (rx control)
4319 *
4320 * 15..13 mode
4321 * 000=HDLC/SDLC
4322 * 001=raw bit synchronous
4323 * 010=asynchronous/isochronous
4324 * 011=monosync byte synchronous
4325 * 100=bisync byte synchronous
4326 * 101=xsync byte synchronous
4327 * 12..10 encoding
4328 * 09 CRC enable
4329 * 08 CRC32
4330 * 07..03 reserved, must be 0
4331 * 02 reset
4332 * 01 enable
4333 * 00 auto-DCD enable
4334 */
4335 val = 0;
4336
4337 switch(info->params.mode) {
4338 case MGSL_MODE_XSYNC:
4339 val |= BIT15 + BIT13;
4340 break;
4341 case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4342 case MGSL_MODE_BISYNC: val |= BIT15; break;
4343 case MGSL_MODE_RAW: val |= BIT13; break;
4344 }
4345
4346 switch(info->params.encoding)
4347 {
4348 case HDLC_ENCODING_NRZB: val |= BIT10; break;
4349 case HDLC_ENCODING_NRZI_MARK: val |= BIT11; break;
4350 case HDLC_ENCODING_NRZI: val |= BIT11 + BIT10; break;
4351 case HDLC_ENCODING_BIPHASE_MARK: val |= BIT12; break;
4352 case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4353 case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4354 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4355 }
4356
4357 switch (info->params.crc_type & HDLC_CRC_MASK)
4358 {
4359 case HDLC_CRC_16_CCITT: val |= BIT9; break;
4360 case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4361 }
4362
4363 if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4364 val |= BIT0;
4365
4366 wr_reg16(info, RCR, val);
4367
4368 /* CCR (clock control)
4369 *
4370 * 07..05 tx clock source
4371 * 04..02 rx clock source
4372 * 01 auxclk enable
4373 * 00 BRG enable
4374 */
4375 val = 0;
4376
4377 if (info->params.flags & HDLC_FLAG_TXC_BRG)
4378 {
4379 // when RxC source is DPLL, BRG generates 16X DPLL
4380 // reference clock, so take TxC from BRG/16 to get
4381 // transmit clock at actual data rate
4382 if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4383 val |= BIT6 + BIT5; /* 011, txclk = BRG/16 */
4384 else
4385 val |= BIT6; /* 010, txclk = BRG */
4386 }
4387 else if (info->params.flags & HDLC_FLAG_TXC_DPLL)
4388 val |= BIT7; /* 100, txclk = DPLL Input */
4389 else if (info->params.flags & HDLC_FLAG_TXC_RXCPIN)
4390 val |= BIT5; /* 001, txclk = RXC Input */
4391
4392 if (info->params.flags & HDLC_FLAG_RXC_BRG)
4393 val |= BIT3; /* 010, rxclk = BRG */
4394 else if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4395 val |= BIT4; /* 100, rxclk = DPLL */
4396 else if (info->params.flags & HDLC_FLAG_RXC_TXCPIN)
4397 val |= BIT2; /* 001, rxclk = TXC Input */
4398
4399 if (info->params.clock_speed)
4400 val |= BIT1 + BIT0;
4401
4402 wr_reg8(info, CCR, (unsigned char)val);
4403
4404 if (info->params.flags & (HDLC_FLAG_TXC_DPLL + HDLC_FLAG_RXC_DPLL))
4405 {
4406 // program DPLL mode
4407 switch(info->params.encoding)
4408 {
4409 case HDLC_ENCODING_BIPHASE_MARK:
4410 case HDLC_ENCODING_BIPHASE_SPACE:
4411 val = BIT7; break;
4412 case HDLC_ENCODING_BIPHASE_LEVEL:
4413 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL:
4414 val = BIT7 + BIT6; break;
4415 default: val = BIT6; // NRZ encodings
4416 }
4417 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | val));
4418
4419 // DPLL requires a 16X reference clock from BRG
4420 set_rate(info, info->params.clock_speed * 16);
4421 }
4422 else
4423 set_rate(info, info->params.clock_speed);
4424
4425 tx_set_idle(info);
4426
4427 msc_set_vcr(info);
4428
4429 /* SCR (serial control)
4430 *
4431 * 15 1=tx req on FIFO half empty
4432 * 14 1=rx req on FIFO half full
4433 * 13 tx data IRQ enable
4434 * 12 tx idle IRQ enable
4435 * 11 underrun IRQ enable
4436 * 10 rx data IRQ enable
4437 * 09 rx idle IRQ enable
4438 * 08 overrun IRQ enable
4439 * 07 DSR IRQ enable
4440 * 06 CTS IRQ enable
4441 * 05 DCD IRQ enable
4442 * 04 RI IRQ enable
4443 * 03 reserved, must be zero
4444 * 02 1=txd->rxd internal loopback enable
4445 * 01 reserved, must be zero
4446 * 00 1=master IRQ enable
4447 */
4448 wr_reg16(info, SCR, BIT15 + BIT14 + BIT0);
4449
4450 if (info->params.loopback)
4451 enable_loopback(info);
4452 }
4453
4454 /*
4455 * set transmit idle mode
4456 */
tx_set_idle(struct slgt_info * info)4457 static void tx_set_idle(struct slgt_info *info)
4458 {
4459 unsigned char val;
4460 unsigned short tcr;
4461
4462 /* if preamble enabled (tcr[6] == 1) then tx idle size = 8 bits
4463 * else tcr[5:4] = tx idle size: 00 = 8 bits, 01 = 16 bits
4464 */
4465 tcr = rd_reg16(info, TCR);
4466 if (info->idle_mode & HDLC_TXIDLE_CUSTOM_16) {
4467 /* disable preamble, set idle size to 16 bits */
4468 tcr = (tcr & ~(BIT6 + BIT5)) | BIT4;
4469 /* MSB of 16 bit idle specified in tx preamble register (TPR) */
4470 wr_reg8(info, TPR, (unsigned char)((info->idle_mode >> 8) & 0xff));
4471 } else if (!(tcr & BIT6)) {
4472 /* preamble is disabled, set idle size to 8 bits */
4473 tcr &= ~(BIT5 + BIT4);
4474 }
4475 wr_reg16(info, TCR, tcr);
4476
4477 if (info->idle_mode & (HDLC_TXIDLE_CUSTOM_8 | HDLC_TXIDLE_CUSTOM_16)) {
4478 /* LSB of custom tx idle specified in tx idle register */
4479 val = (unsigned char)(info->idle_mode & 0xff);
4480 } else {
4481 /* standard 8 bit idle patterns */
4482 switch(info->idle_mode)
4483 {
4484 case HDLC_TXIDLE_FLAGS: val = 0x7e; break;
4485 case HDLC_TXIDLE_ALT_ZEROS_ONES:
4486 case HDLC_TXIDLE_ALT_MARK_SPACE: val = 0xaa; break;
4487 case HDLC_TXIDLE_ZEROS:
4488 case HDLC_TXIDLE_SPACE: val = 0x00; break;
4489 default: val = 0xff;
4490 }
4491 }
4492
4493 wr_reg8(info, TIR, val);
4494 }
4495
4496 /*
4497 * get state of V24 status (input) signals
4498 */
get_signals(struct slgt_info * info)4499 static void get_signals(struct slgt_info *info)
4500 {
4501 unsigned short status = rd_reg16(info, SSR);
4502
4503 /* clear all serial signals except RTS and DTR */
4504 info->signals &= SerialSignal_RTS | SerialSignal_DTR;
4505
4506 if (status & BIT3)
4507 info->signals |= SerialSignal_DSR;
4508 if (status & BIT2)
4509 info->signals |= SerialSignal_CTS;
4510 if (status & BIT1)
4511 info->signals |= SerialSignal_DCD;
4512 if (status & BIT0)
4513 info->signals |= SerialSignal_RI;
4514 }
4515
4516 /*
4517 * set V.24 Control Register based on current configuration
4518 */
msc_set_vcr(struct slgt_info * info)4519 static void msc_set_vcr(struct slgt_info *info)
4520 {
4521 unsigned char val = 0;
4522
4523 /* VCR (V.24 control)
4524 *
4525 * 07..04 serial IF select
4526 * 03 DTR
4527 * 02 RTS
4528 * 01 LL
4529 * 00 RL
4530 */
4531
4532 switch(info->if_mode & MGSL_INTERFACE_MASK)
4533 {
4534 case MGSL_INTERFACE_RS232:
4535 val |= BIT5; /* 0010 */
4536 break;
4537 case MGSL_INTERFACE_V35:
4538 val |= BIT7 + BIT6 + BIT5; /* 1110 */
4539 break;
4540 case MGSL_INTERFACE_RS422:
4541 val |= BIT6; /* 0100 */
4542 break;
4543 }
4544
4545 if (info->if_mode & MGSL_INTERFACE_MSB_FIRST)
4546 val |= BIT4;
4547 if (info->signals & SerialSignal_DTR)
4548 val |= BIT3;
4549 if (info->signals & SerialSignal_RTS)
4550 val |= BIT2;
4551 if (info->if_mode & MGSL_INTERFACE_LL)
4552 val |= BIT1;
4553 if (info->if_mode & MGSL_INTERFACE_RL)
4554 val |= BIT0;
4555 wr_reg8(info, VCR, val);
4556 }
4557
4558 /*
4559 * set state of V24 control (output) signals
4560 */
set_signals(struct slgt_info * info)4561 static void set_signals(struct slgt_info *info)
4562 {
4563 unsigned char val = rd_reg8(info, VCR);
4564 if (info->signals & SerialSignal_DTR)
4565 val |= BIT3;
4566 else
4567 val &= ~BIT3;
4568 if (info->signals & SerialSignal_RTS)
4569 val |= BIT2;
4570 else
4571 val &= ~BIT2;
4572 wr_reg8(info, VCR, val);
4573 }
4574
4575 /*
4576 * free range of receive DMA buffers (i to last)
4577 */
free_rbufs(struct slgt_info * info,unsigned int i,unsigned int last)4578 static void free_rbufs(struct slgt_info *info, unsigned int i, unsigned int last)
4579 {
4580 int done = 0;
4581
4582 while(!done) {
4583 /* reset current buffer for reuse */
4584 info->rbufs[i].status = 0;
4585 set_desc_count(info->rbufs[i], info->rbuf_fill_level);
4586 if (i == last)
4587 done = 1;
4588 if (++i == info->rbuf_count)
4589 i = 0;
4590 }
4591 info->rbuf_current = i;
4592 }
4593
4594 /*
4595 * mark all receive DMA buffers as free
4596 */
reset_rbufs(struct slgt_info * info)4597 static void reset_rbufs(struct slgt_info *info)
4598 {
4599 free_rbufs(info, 0, info->rbuf_count - 1);
4600 info->rbuf_fill_index = 0;
4601 info->rbuf_fill_count = 0;
4602 }
4603
4604 /*
4605 * pass receive HDLC frame to upper layer
4606 *
4607 * return true if frame available, otherwise false
4608 */
rx_get_frame(struct slgt_info * info)4609 static bool rx_get_frame(struct slgt_info *info)
4610 {
4611 unsigned int start, end;
4612 unsigned short status;
4613 unsigned int framesize = 0;
4614 unsigned long flags;
4615 struct tty_struct *tty = info->port.tty;
4616 unsigned char addr_field = 0xff;
4617 unsigned int crc_size = 0;
4618
4619 switch (info->params.crc_type & HDLC_CRC_MASK) {
4620 case HDLC_CRC_16_CCITT: crc_size = 2; break;
4621 case HDLC_CRC_32_CCITT: crc_size = 4; break;
4622 }
4623
4624 check_again:
4625
4626 framesize = 0;
4627 addr_field = 0xff;
4628 start = end = info->rbuf_current;
4629
4630 for (;;) {
4631 if (!desc_complete(info->rbufs[end]))
4632 goto cleanup;
4633
4634 if (framesize == 0 && info->params.addr_filter != 0xff)
4635 addr_field = info->rbufs[end].buf[0];
4636
4637 framesize += desc_count(info->rbufs[end]);
4638
4639 if (desc_eof(info->rbufs[end]))
4640 break;
4641
4642 if (++end == info->rbuf_count)
4643 end = 0;
4644
4645 if (end == info->rbuf_current) {
4646 if (info->rx_enabled){
4647 spin_lock_irqsave(&info->lock,flags);
4648 rx_start(info);
4649 spin_unlock_irqrestore(&info->lock,flags);
4650 }
4651 goto cleanup;
4652 }
4653 }
4654
4655 /* status
4656 *
4657 * 15 buffer complete
4658 * 14..06 reserved
4659 * 05..04 residue
4660 * 02 eof (end of frame)
4661 * 01 CRC error
4662 * 00 abort
4663 */
4664 status = desc_status(info->rbufs[end]);
4665
4666 /* ignore CRC bit if not using CRC (bit is undefined) */
4667 if ((info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_NONE)
4668 status &= ~BIT1;
4669
4670 if (framesize == 0 ||
4671 (addr_field != 0xff && addr_field != info->params.addr_filter)) {
4672 free_rbufs(info, start, end);
4673 goto check_again;
4674 }
4675
4676 if (framesize < (2 + crc_size) || status & BIT0) {
4677 info->icount.rxshort++;
4678 framesize = 0;
4679 } else if (status & BIT1) {
4680 info->icount.rxcrc++;
4681 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX))
4682 framesize = 0;
4683 }
4684
4685 #if SYNCLINK_GENERIC_HDLC
4686 if (framesize == 0) {
4687 info->netdev->stats.rx_errors++;
4688 info->netdev->stats.rx_frame_errors++;
4689 }
4690 #endif
4691
4692 DBGBH(("%s rx frame status=%04X size=%d\n",
4693 info->device_name, status, framesize));
4694 DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, info->rbuf_fill_level), "rx");
4695
4696 if (framesize) {
4697 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX)) {
4698 framesize -= crc_size;
4699 crc_size = 0;
4700 }
4701
4702 if (framesize > info->max_frame_size + crc_size)
4703 info->icount.rxlong++;
4704 else {
4705 /* copy dma buffer(s) to contiguous temp buffer */
4706 int copy_count = framesize;
4707 int i = start;
4708 unsigned char *p = info->tmp_rbuf;
4709 info->tmp_rbuf_count = framesize;
4710
4711 info->icount.rxok++;
4712
4713 while(copy_count) {
4714 int partial_count = min_t(int, copy_count, info->rbuf_fill_level);
4715 memcpy(p, info->rbufs[i].buf, partial_count);
4716 p += partial_count;
4717 copy_count -= partial_count;
4718 if (++i == info->rbuf_count)
4719 i = 0;
4720 }
4721
4722 if (info->params.crc_type & HDLC_CRC_RETURN_EX) {
4723 *p = (status & BIT1) ? RX_CRC_ERROR : RX_OK;
4724 framesize++;
4725 }
4726
4727 #if SYNCLINK_GENERIC_HDLC
4728 if (info->netcount)
4729 hdlcdev_rx(info,info->tmp_rbuf, framesize);
4730 else
4731 #endif
4732 ldisc_receive_buf(tty, info->tmp_rbuf, info->flag_buf, framesize);
4733 }
4734 }
4735 free_rbufs(info, start, end);
4736 return true;
4737
4738 cleanup:
4739 return false;
4740 }
4741
4742 /*
4743 * pass receive buffer (RAW synchronous mode) to tty layer
4744 * return true if buffer available, otherwise false
4745 */
rx_get_buf(struct slgt_info * info)4746 static bool rx_get_buf(struct slgt_info *info)
4747 {
4748 unsigned int i = info->rbuf_current;
4749 unsigned int count;
4750
4751 if (!desc_complete(info->rbufs[i]))
4752 return false;
4753 count = desc_count(info->rbufs[i]);
4754 switch(info->params.mode) {
4755 case MGSL_MODE_MONOSYNC:
4756 case MGSL_MODE_BISYNC:
4757 case MGSL_MODE_XSYNC:
4758 /* ignore residue in byte synchronous modes */
4759 if (desc_residue(info->rbufs[i]))
4760 count--;
4761 break;
4762 }
4763 DBGDATA(info, info->rbufs[i].buf, count, "rx");
4764 DBGINFO(("rx_get_buf size=%d\n", count));
4765 if (count)
4766 ldisc_receive_buf(info->port.tty, info->rbufs[i].buf,
4767 info->flag_buf, count);
4768 free_rbufs(info, i, i);
4769 return true;
4770 }
4771
reset_tbufs(struct slgt_info * info)4772 static void reset_tbufs(struct slgt_info *info)
4773 {
4774 unsigned int i;
4775 info->tbuf_current = 0;
4776 for (i=0 ; i < info->tbuf_count ; i++) {
4777 info->tbufs[i].status = 0;
4778 info->tbufs[i].count = 0;
4779 }
4780 }
4781
4782 /*
4783 * return number of free transmit DMA buffers
4784 */
free_tbuf_count(struct slgt_info * info)4785 static unsigned int free_tbuf_count(struct slgt_info *info)
4786 {
4787 unsigned int count = 0;
4788 unsigned int i = info->tbuf_current;
4789
4790 do
4791 {
4792 if (desc_count(info->tbufs[i]))
4793 break; /* buffer in use */
4794 ++count;
4795 if (++i == info->tbuf_count)
4796 i=0;
4797 } while (i != info->tbuf_current);
4798
4799 /* if tx DMA active, last zero count buffer is in use */
4800 if (count && (rd_reg32(info, TDCSR) & BIT0))
4801 --count;
4802
4803 return count;
4804 }
4805
4806 /*
4807 * return number of bytes in unsent transmit DMA buffers
4808 * and the serial controller tx FIFO
4809 */
tbuf_bytes(struct slgt_info * info)4810 static unsigned int tbuf_bytes(struct slgt_info *info)
4811 {
4812 unsigned int total_count = 0;
4813 unsigned int i = info->tbuf_current;
4814 unsigned int reg_value;
4815 unsigned int count;
4816 unsigned int active_buf_count = 0;
4817
4818 /*
4819 * Add descriptor counts for all tx DMA buffers.
4820 * If count is zero (cleared by DMA controller after read),
4821 * the buffer is complete or is actively being read from.
4822 *
4823 * Record buf_count of last buffer with zero count starting
4824 * from current ring position. buf_count is mirror
4825 * copy of count and is not cleared by serial controller.
4826 * If DMA controller is active, that buffer is actively
4827 * being read so add to total.
4828 */
4829 do {
4830 count = desc_count(info->tbufs[i]);
4831 if (count)
4832 total_count += count;
4833 else if (!total_count)
4834 active_buf_count = info->tbufs[i].buf_count;
4835 if (++i == info->tbuf_count)
4836 i = 0;
4837 } while (i != info->tbuf_current);
4838
4839 /* read tx DMA status register */
4840 reg_value = rd_reg32(info, TDCSR);
4841
4842 /* if tx DMA active, last zero count buffer is in use */
4843 if (reg_value & BIT0)
4844 total_count += active_buf_count;
4845
4846 /* add tx FIFO count = reg_value[15..8] */
4847 total_count += (reg_value >> 8) & 0xff;
4848
4849 /* if transmitter active add one byte for shift register */
4850 if (info->tx_active)
4851 total_count++;
4852
4853 return total_count;
4854 }
4855
4856 /*
4857 * load data into transmit DMA buffer ring and start transmitter if needed
4858 * return true if data accepted, otherwise false (buffers full)
4859 */
tx_load(struct slgt_info * info,const char * buf,unsigned int size)4860 static bool tx_load(struct slgt_info *info, const char *buf, unsigned int size)
4861 {
4862 unsigned short count;
4863 unsigned int i;
4864 struct slgt_desc *d;
4865
4866 /* check required buffer space */
4867 if (DIV_ROUND_UP(size, DMABUFSIZE) > free_tbuf_count(info))
4868 return false;
4869
4870 DBGDATA(info, buf, size, "tx");
4871
4872 /*
4873 * copy data to one or more DMA buffers in circular ring
4874 * tbuf_start = first buffer for this data
4875 * tbuf_current = next free buffer
4876 *
4877 * Copy all data before making data visible to DMA controller by
4878 * setting descriptor count of the first buffer.
4879 * This prevents an active DMA controller from reading the first DMA
4880 * buffers of a frame and stopping before the final buffers are filled.
4881 */
4882
4883 info->tbuf_start = i = info->tbuf_current;
4884
4885 while (size) {
4886 d = &info->tbufs[i];
4887
4888 count = (unsigned short)((size > DMABUFSIZE) ? DMABUFSIZE : size);
4889 memcpy(d->buf, buf, count);
4890
4891 size -= count;
4892 buf += count;
4893
4894 /*
4895 * set EOF bit for last buffer of HDLC frame or
4896 * for every buffer in raw mode
4897 */
4898 if ((!size && info->params.mode == MGSL_MODE_HDLC) ||
4899 info->params.mode == MGSL_MODE_RAW)
4900 set_desc_eof(*d, 1);
4901 else
4902 set_desc_eof(*d, 0);
4903
4904 /* set descriptor count for all but first buffer */
4905 if (i != info->tbuf_start)
4906 set_desc_count(*d, count);
4907 d->buf_count = count;
4908
4909 if (++i == info->tbuf_count)
4910 i = 0;
4911 }
4912
4913 info->tbuf_current = i;
4914
4915 /* set first buffer count to make new data visible to DMA controller */
4916 d = &info->tbufs[info->tbuf_start];
4917 set_desc_count(*d, d->buf_count);
4918
4919 /* start transmitter if needed and update transmit timeout */
4920 if (!info->tx_active)
4921 tx_start(info);
4922 update_tx_timer(info);
4923
4924 return true;
4925 }
4926
register_test(struct slgt_info * info)4927 static int register_test(struct slgt_info *info)
4928 {
4929 static unsigned short patterns[] =
4930 {0x0000, 0xffff, 0xaaaa, 0x5555, 0x6969, 0x9696};
4931 static unsigned int count = ARRAY_SIZE(patterns);
4932 unsigned int i;
4933 int rc = 0;
4934
4935 for (i=0 ; i < count ; i++) {
4936 wr_reg16(info, TIR, patterns[i]);
4937 wr_reg16(info, BDR, patterns[(i+1)%count]);
4938 if ((rd_reg16(info, TIR) != patterns[i]) ||
4939 (rd_reg16(info, BDR) != patterns[(i+1)%count])) {
4940 rc = -ENODEV;
4941 break;
4942 }
4943 }
4944 info->gpio_present = (rd_reg32(info, JCR) & BIT5) ? 1 : 0;
4945 info->init_error = rc ? 0 : DiagStatus_AddressFailure;
4946 return rc;
4947 }
4948
irq_test(struct slgt_info * info)4949 static int irq_test(struct slgt_info *info)
4950 {
4951 unsigned long timeout;
4952 unsigned long flags;
4953 struct tty_struct *oldtty = info->port.tty;
4954 u32 speed = info->params.data_rate;
4955
4956 info->params.data_rate = 921600;
4957 info->port.tty = NULL;
4958
4959 spin_lock_irqsave(&info->lock, flags);
4960 async_mode(info);
4961 slgt_irq_on(info, IRQ_TXIDLE);
4962
4963 /* enable transmitter */
4964 wr_reg16(info, TCR,
4965 (unsigned short)(rd_reg16(info, TCR) | BIT1));
4966
4967 /* write one byte and wait for tx idle */
4968 wr_reg16(info, TDR, 0);
4969
4970 /* assume failure */
4971 info->init_error = DiagStatus_IrqFailure;
4972 info->irq_occurred = false;
4973
4974 spin_unlock_irqrestore(&info->lock, flags);
4975
4976 timeout=100;
4977 while(timeout-- && !info->irq_occurred)
4978 msleep_interruptible(10);
4979
4980 spin_lock_irqsave(&info->lock,flags);
4981 reset_port(info);
4982 spin_unlock_irqrestore(&info->lock,flags);
4983
4984 info->params.data_rate = speed;
4985 info->port.tty = oldtty;
4986
4987 info->init_error = info->irq_occurred ? 0 : DiagStatus_IrqFailure;
4988 return info->irq_occurred ? 0 : -ENODEV;
4989 }
4990
loopback_test_rx(struct slgt_info * info)4991 static int loopback_test_rx(struct slgt_info *info)
4992 {
4993 unsigned char *src, *dest;
4994 int count;
4995
4996 if (desc_complete(info->rbufs[0])) {
4997 count = desc_count(info->rbufs[0]);
4998 src = info->rbufs[0].buf;
4999 dest = info->tmp_rbuf;
5000
5001 for( ; count ; count-=2, src+=2) {
5002 /* src=data byte (src+1)=status byte */
5003 if (!(*(src+1) & (BIT9 + BIT8))) {
5004 *dest = *src;
5005 dest++;
5006 info->tmp_rbuf_count++;
5007 }
5008 }
5009 DBGDATA(info, info->tmp_rbuf, info->tmp_rbuf_count, "rx");
5010 return 1;
5011 }
5012 return 0;
5013 }
5014
loopback_test(struct slgt_info * info)5015 static int loopback_test(struct slgt_info *info)
5016 {
5017 #define TESTFRAMESIZE 20
5018
5019 unsigned long timeout;
5020 u16 count = TESTFRAMESIZE;
5021 unsigned char buf[TESTFRAMESIZE];
5022 int rc = -ENODEV;
5023 unsigned long flags;
5024
5025 struct tty_struct *oldtty = info->port.tty;
5026 MGSL_PARAMS params;
5027
5028 memcpy(¶ms, &info->params, sizeof(params));
5029
5030 info->params.mode = MGSL_MODE_ASYNC;
5031 info->params.data_rate = 921600;
5032 info->params.loopback = 1;
5033 info->port.tty = NULL;
5034
5035 /* build and send transmit frame */
5036 for (count = 0; count < TESTFRAMESIZE; ++count)
5037 buf[count] = (unsigned char)count;
5038
5039 info->tmp_rbuf_count = 0;
5040 memset(info->tmp_rbuf, 0, TESTFRAMESIZE);
5041
5042 /* program hardware for HDLC and enabled receiver */
5043 spin_lock_irqsave(&info->lock,flags);
5044 async_mode(info);
5045 rx_start(info);
5046 tx_load(info, buf, count);
5047 spin_unlock_irqrestore(&info->lock, flags);
5048
5049 /* wait for receive complete */
5050 for (timeout = 100; timeout; --timeout) {
5051 msleep_interruptible(10);
5052 if (loopback_test_rx(info)) {
5053 rc = 0;
5054 break;
5055 }
5056 }
5057
5058 /* verify received frame length and contents */
5059 if (!rc && (info->tmp_rbuf_count != count ||
5060 memcmp(buf, info->tmp_rbuf, count))) {
5061 rc = -ENODEV;
5062 }
5063
5064 spin_lock_irqsave(&info->lock,flags);
5065 reset_adapter(info);
5066 spin_unlock_irqrestore(&info->lock,flags);
5067
5068 memcpy(&info->params, ¶ms, sizeof(info->params));
5069 info->port.tty = oldtty;
5070
5071 info->init_error = rc ? DiagStatus_DmaFailure : 0;
5072 return rc;
5073 }
5074
adapter_test(struct slgt_info * info)5075 static int adapter_test(struct slgt_info *info)
5076 {
5077 DBGINFO(("testing %s\n", info->device_name));
5078 if (register_test(info) < 0) {
5079 printk("register test failure %s addr=%08X\n",
5080 info->device_name, info->phys_reg_addr);
5081 } else if (irq_test(info) < 0) {
5082 printk("IRQ test failure %s IRQ=%d\n",
5083 info->device_name, info->irq_level);
5084 } else if (loopback_test(info) < 0) {
5085 printk("loopback test failure %s\n", info->device_name);
5086 }
5087 return info->init_error;
5088 }
5089
5090 /*
5091 * transmit timeout handler
5092 */
tx_timeout(struct timer_list * t)5093 static void tx_timeout(struct timer_list *t)
5094 {
5095 struct slgt_info *info = from_timer(info, t, tx_timer);
5096 unsigned long flags;
5097
5098 DBGINFO(("%s tx_timeout\n", info->device_name));
5099 if(info->tx_active && info->params.mode == MGSL_MODE_HDLC) {
5100 info->icount.txtimeout++;
5101 }
5102 spin_lock_irqsave(&info->lock,flags);
5103 tx_stop(info);
5104 spin_unlock_irqrestore(&info->lock,flags);
5105
5106 #if SYNCLINK_GENERIC_HDLC
5107 if (info->netcount)
5108 hdlcdev_tx_done(info);
5109 else
5110 #endif
5111 bh_transmit(info);
5112 }
5113
5114 /*
5115 * receive buffer polling timer
5116 */
rx_timeout(struct timer_list * t)5117 static void rx_timeout(struct timer_list *t)
5118 {
5119 struct slgt_info *info = from_timer(info, t, rx_timer);
5120 unsigned long flags;
5121
5122 DBGINFO(("%s rx_timeout\n", info->device_name));
5123 spin_lock_irqsave(&info->lock, flags);
5124 info->pending_bh |= BH_RECEIVE;
5125 spin_unlock_irqrestore(&info->lock, flags);
5126 bh_handler(&info->task);
5127 }
5128
5129
