Searched refs:disabling (Results 1 – 25 of 173) sorted by relevance
1234567
| /Linux-v5.4/Documentation/ |
| D | preempt-locking.txt | 35 protect these situations by disabling preemption around them.
72 Data protection under preemption is achieved by disabling preemption for the
93 disabling preemption - any cond_resched() or cond_resched_lock() might trigger
95 reschedule. So use this implicit preemption-disabling property only if you
125 Preventing preemption using interrupt disabling
132 in doubt, rely on locking or explicit preemption disabling.
134 Note in 2.5 interrupt disabling is now only per-CPU (e.g. local).
|
| /Linux-v5.4/drivers/staging/unisys/Documentation/ABI/ |
| D | sysfs-platform-visorchipset | 59 responsible for enabling and disabling SR-IOV devices when the
63 first disabling all VFs attached to that PF. s-Par handles this
78 responsible for enabling and disabling SR-IOV devices when the
82 first disabling all VFs attached to that PF. s-Par handles this
|
| /Linux-v5.4/Documentation/devicetree/bindings/powerpc/fsl/ |
| D | pmc.txt | 41 supports disabling and resuming devices at any time.
46 This sleep controller only supports disabling devices during system
53 disabling. This sleep controller does not support configuring devices
|
| /Linux-v5.4/Documentation/devicetree/bindings/leds/backlight/ |
| D | gpio-backlight.txt | 5 - gpios: describes the gpio that is used for enabling/disabling the backlight.
|
| D | pwm-backlight.txt | 15 - pwm-off-delay-ms: Delay in ms between disabling the backlight using GPIO
|
| /Linux-v5.4/Documentation/devicetree/bindings/net/nfc/ |
| D | s3fwrn5.txt | 7 - s3fwrn5,en-gpios: Output GPIO pin used for enabling/disabling the chip
|
| D | pn544.txt | 8 - enable-gpios: Output GPIO pin used for enabling/disabling the PN544
|
| D | nxp-nci.txt | 8 - enable-gpios: Output GPIO pin used for enabling/disabling the chip
|
| D | st21nfca.txt | 7 - enable-gpios: Output GPIO pin used for enabling/disabling the ST21NFCA
|
| /Linux-v5.4/Documentation/devicetree/bindings/clock/ |
| D | gpio-gate-clock.txt | 10 - enable-gpios : GPIO reference for enabling and disabling the clock.
|
| /Linux-v5.4/Documentation/devicetree/bindings/ata/ |
| D | ahci-da850.txt | 9 for enabling/disabling the SATA clock receiver
|
| /Linux-v5.4/drivers/gpu/drm/imx/ |
| D | ipuv3-plane.h | 29 bool disabling; member
|
| /Linux-v5.4/arch/arm/boot/compressed/ |
| D | head-xscale.S | 30 @ disabling MMU and caches
|
| /Linux-v5.4/Documentation/devicetree/bindings/powerpc/opal/ |
| D | sensor-groups.txt | 26 sensor groups like clearing min/max, enabling/disabling sensor
|
| /Linux-v5.4/drivers/thermal/qcom/ |
| D | Kconfig | 9 thermal zone device via the mode file results in disabling the sensor.
|
| /Linux-v5.4/Documentation/devicetree/bindings/gpio/ |
| D | intel,ixp4xx-gpio.txt | 8 actual enabling/disabling of the interrupt line is done in the
|
| /Linux-v5.4/Documentation/driver-api/mmc/ |
| D | mmc-tools.rst | 18 - Set the eMMC data sector size to 4KB by disabling emulation.
|
| /Linux-v5.4/Documentation/devicetree/bindings/input/rmi4/ |
| D | rmi_f01.txt | 16 and 2 will enable nosleep (disabling sleep).
|
| D | rmi_2d_sensor.txt | 36 - syna,disable-report-mask: Mask for disabling posiiton reporting. Used to
|
| /Linux-v5.4/Documentation/devicetree/bindings/mips/ |
| D | mscc.txt | 32 the CPU: 8 general purpose registers, reset control, CPU en/disabling, CPU
|
| /Linux-v5.4/Documentation/devicetree/bindings/arm/firmware/ |
| D | sdei.txt | 10 and enabling/disabling events. Functions are invoked by trapping to the
|
| /Linux-v5.4/drivers/net/ethernet/toshiba/ |
| D | Kconfig | 38 use wireless feature, disabling this option saves memory. As
|
| /Linux-v5.4/Documentation/media/uapi/rc/ |
| D | lirc-set-wideband-receiver.rst | 43 allows enabling or disabling it.
|
| /Linux-v5.4/Documentation/devicetree/bindings/clock/ti/ |
| D | interface.txt | 31 - ti,bit-shift : bit shift for the bit enabling/disabling the clock (default 0)
|
| /Linux-v5.4/Documentation/driver-api/usb/ |
| D | usb3-debug-port.rst | 76 [ 1815.999595] usb 4-3: LPM exit latency is zeroed, disabling LPM.
144 [ 79.475003] usb 2-2.1: LPM exit latency is zeroed, disabling LPM.
|
1234567
