Searched refs:conversion (Results 1 – 25 of 150) sorted by relevance
123456
| /Linux-v5.4/Documentation/hwmon/ |
| D | ina3221.rst | 23 and supply voltage, with programmable conversion times and averaging, current
50 update_interval Data conversion time in millisecond, following:
56 * BC: bus-voltage conversion time in millisecond
57 * SC: shunt-voltage conversion time in millisecond
59 Affects both Bus- and Shunt-voltage conversion time.
61 and SC to 140 us (minimum conversion time).
|
| D | lm73.rst | 33 affects the conversion time of the LM73's analog-to-digital converter.
35 conversion time via the 'update_interval' sysfs attribute for the
50 used to change the conversion time::
79 conversion time actively in use.
81 Mathematically, the resolution can be derived from the conversion time
|
| D | max197.rst | 35 filled with a pointer to a conversion function, defined like::
39 ctrl is the control byte to write to start a new conversion.
50 3 BIP Unipolar or Bipolar conversion mode
58 in[0-7]_input The conversion value for the corresponding channel.
|
| D | ina2xx.rst | 63 programmable conversion times and filtering.
82 bus and shunt voltage conversion times multiplied by the averaging rate. We
83 don't touch the conversion times and only modify the number of averages. The
102 update_interval data conversion time; affects number of samples used
|
| D | da9055.rst | 18 multiplexer. The analogue input multiplexer will allow conversion of up to 5
20 the input of the ADC during the conversion.
|
| D | da9052.rst | 19 multiplexer. The analogue input multiplexer will allow conversion of up to 10
21 the input of the ADC during the conversion.
|
| D | ds1621.rst | 172 used to change the conversion time::
206 after a write operation provides the conversion time used by the device.
208 Mathematically, the resolution can be derived from the conversion time
217 - 93.75ms = minimum conversion time
|
| /Linux-v5.4/Documentation/devicetree/bindings/input/touchscreen/ |
| D | ad7879.txt | 14 - adi,first-conversion-delay : 0-12: In 128us steps (starting with 128us)
34 - adi,conversion-interval: : 0 : convert one time only
48 adi,first-conversion-delay = /bits/ 8 <3>;
52 adi,conversion-interval = /bits/ 8 <255>;
66 adi,first-conversion-delay = /bits/ 8 <3>;
70 adi,conversion-interval = /bits/ 8 <255>;
|
| D | fsl-mx25-tcq.txt | 1 Freescale mx25 TS conversion queue module
3 mx25 touchscreen conversion queue module which controls the ADC unit of the
24 This device includes two conversion queues which can be added as subnodes.
|
| /Linux-v5.4/scripts/coccinelle/misc/ |
| D | boolconv.cocci | 2 /// Remove unneeded conversion to bool
5 //# explicit conversion is overly verbose and unneeded.
79 msg = "WARNING: conversion to bool not needed here"
90 msg = "WARNING: conversion to bool not needed here"
|
| /Linux-v5.4/Documentation/devicetree/bindings/mfd/ |
| D | fsl-imx25-tsadc.txt | 3 This device combines two general purpose conversion queues one used for general
15 conversion queues.
20 This device includes two conversion queues which can be added as subnodes.
|
| /Linux-v5.4/Documentation/devicetree/bindings/iio/adc/ |
| D | ti-adc12138.txt | 9 - interrupts: Should contain interrupt for EOC (end of conversion)
10 - clocks: phandle to conversion clock input
19 - ti,acquisition-time: The number of conversion clock periods for the S/H's
|
| D | vf610-adc.txt | 16 requirements. Three values are required, depending on conversion mode:
21 to be chosen according to the conversion mode and the connected analog
24 C_as as well as conversion modes is 1000ns.
|
| /Linux-v5.4/Documentation/w1/slaves/ |
| D | w1_therm.rst | 16 w1_therm provides basic temperature conversion for ds18*20 devices, and the
30 read sequence will initiate a temperature conversion then provide two
38 temperature conversion at a time. If none of the devices are parasite
42 precision (which would also reduce the conversion time) when reading values.
62 driven when the conversion is taking place, provided the master driver
|
| D | w1_ds2438.rst | 49 Opening and reading this file initiates the CONVERT_T (temperature conversion)
58 Opening and reading this file initiates the CONVERT_V (voltage conversion)
68 After the voltage conversion the value is returned as decimal ASCII.
|
| /Linux-v5.4/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-vf610 | 5 Specifies the hardware conversion mode used. The three
14 Specifies the hardware conversion mode used within DAC.
|
| D | sysfs-bus-iio-ina2xx-adc | 8 buffer. This synchronizes the in-chip conversion rate with the
14 or repeated, depending on the beat between the capture and conversion
|
| /Linux-v5.4/Documentation/devicetree/bindings/media/ |
| D | fsl-pxp.txt | 5 that supports scaling, colorspace conversion, alpha blending, rotation, and
6 pixel conversion via lookup table. Different versions are present on various
|
| /Linux-v5.4/tools/perf/Documentation/ |
| D | perf-data.txt | 21 It's possible to set data-convert debug variable to get debug messages from conversion,
28 Triggers the CTF conversion, specify the path of CTF data directory.
|
| /Linux-v5.4/Documentation/devicetree/bindings/media/i2c/ |
| D | tvp514x.txt | 6 to-digital (A/D) conversion of component RGB and YPbPr signals as well as A/D
7 conversion and decoding of NTSC, PAL and SECAM composite and S-video into
|
| /Linux-v5.4/drivers/staging/media/ipu3/ |
| D | TODO | 4 - Request API conversion. Remove of the dual pipeline and associate buffers
16 Further clarification on some ambiguities such as data type conversion of
|
| /Linux-v5.4/Documentation/driver-api/iio/ |
| D | intro.rst | 9 analog-to-digital conversion (ADC) or digital-to-analog conversion (DAC)
|
| /Linux-v5.4/drivers/gpu/drm/amd/display/dc/basics/ |
| D | Makefile | 27 BASICS = conversion.o fixpt31_32.o \
|
| /Linux-v5.4/drivers/gpu/drm/rcar-du/ |
| D | rcar_du_of_lvds_r8a7791.dts | 3 * rcar_du_of_lvds_r8a7791.dts - Legacy LVDS DT bindings conversion for R8A7791
|
| D | rcar_du_of_lvds_r8a7793.dts | 3 * rcar_du_of_lvds_r8a7793.dts - Legacy LVDS DT bindings conversion for R8A7793
|
123456
