| /Linux-v5.4/drivers/gpu/drm/nouveau/nvkm/subdev/bios/ |
| D | boost.c | 33 u32 boost = 0; in nvbios_boostTe() local
37 boost = nvbios_rd32(bios, bit_P.offset + 0x30); in nvbios_boostTe()
39 if (boost) { in nvbios_boostTe()
40 *ver = nvbios_rd08(bios, boost + 0); in nvbios_boostTe()
43 *hdr = nvbios_rd08(bios, boost + 1); in nvbios_boostTe()
44 *cnt = nvbios_rd08(bios, boost + 5); in nvbios_boostTe()
45 *len = nvbios_rd08(bios, boost + 2); in nvbios_boostTe()
46 *snr = nvbios_rd08(bios, boost + 4); in nvbios_boostTe()
47 *ssz = nvbios_rd08(bios, boost + 3); in nvbios_boostTe()
48 return boost; in nvbios_boostTe()
|
| /Linux-v5.4/Documentation/devicetree/bindings/power/supply/ |
| D | bq25890.txt | 19 - ti,boost-voltage: integer, VBUS voltage level in boost mode (in uV);
20 - ti,boost-max-current: integer, maximum allowed current draw in boost mode
24 - ti,boost-low-freq: boolean, if present boost mode frequency will be 500kHz,
44 ti,boost-voltage = <5000000>;
45 ti,boost-max-current = <1000000>;
|
| D | rt9455_charger.txt | 16 - richtek,boost-output-voltage: integer, maximum voltage provided to consumer
17 devices, when the charger is in boost mode, in uV.
42 richtek,boost-output-voltage = <5050000>;
|
| /Linux-v5.4/Documentation/devicetree/bindings/sound/ |
| D | cs35l34.txt | 13 - cirrus,boost-vtge-millivolt : Boost Voltage Value. Configures the boost
17 - cirrus,boost-nanohenry: Inductor value for boost converter. The value is
28 - cirrus,boost-peak-milliamp : Boost converter peak current limit in mA. The
59 cirrus,boost-vtge-milltvolt = <8000>; /* 8V */
60 cirrus,boost-ind-nanohenry = <1000>; /* 1uH */
61 cirrus,boost-peak-milliamp = <3000>; /* 3A */
|
| D | cs35l36.txt | 13 - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
18 - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
19 Configures the peak current by monitoring the current through the boost FET.
24 - cirrus,boost-ind-nanohenry : Inductor estimation LBST reference value.
25 Seeds the digital boost converter's inductor estimation block with the initial
36 - cirrus,boost-ctl-select : Boost conerter control source selection.
37 Selects the source of the BST_CTL target VBST voltage for the boost
53 This enables the digital boost converter to operate in a low power
147 cirrus,boost-ind-nanohenry = <1000>;
148 cirrus,boost-ctl-millivolt = <10000>;
[all …]
|
| D | cs35l35.txt | 17 - cirrus,boost-ind-nanohenry: Inductor value for boost converter. The value is
34 - cirrus,shared-boost : Boolean to enable ClassH tracking of Advisory Signal
37 - cirrus,external-boost : Boolean to specify the device is using an external
38 boost supply, note that sharing a boost from another cs35l35 would constitute
55 - cirrus,boost-ctl-millivolt : Boost Voltage Value. Configures the boost
60 - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
61 Configures the peak current by monitoring the current through the boost FET.
150 cirrus,boost-ctl-millivolt = <9000>;
155 cirrus,shared-boost;
|
| D | cs35l33.txt | 21 - cirrus,boost-ctl : Booster voltage use to supply the amp. If the value is
22 0, then VBST = VP. If greater than 0, the boost voltage will be 3300mV with
34 - cirrus,boost-ipk : The maximum current allowed for the boost converter.
109 cirrus,boost-ctl = <0x30>; /* VBST = 8000mV */
110 cirrus,boost-ipk = <0xE0>; /* 3600mA */
|
| D | cs35l32.txt | 18 - cirrus,boost-manager : Boost voltage control.
59 cirrus,boost-manager = <0x03>;
|
| /Linux-v5.4/Documentation/devicetree/bindings/mfd/ |
| D | max77693.txt | 89 - maxim,boost-mode :
90 In boost mode the device can produce up to 1.2A of total current
92 to 625mA then. If not enabled explicitly, boost setting defaults to
95 LEDS_BOOST_OFF (0) - no boost,
98 - maxim,boost-mvout : Output voltage of the boost module in millivolts.
117 (boost mode must be turned off):
181 maxim,boost-mode = <LEDS_BOOST_FIXED>;
182 maxim,boost-mvout = <5000>;
|
| /Linux-v5.4/Documentation/devicetree/bindings/leds/backlight/ |
| D | pm8941-wled.txt | 16 - qcom,current-boost-limit: mA; boost current limit; one of:
38 qcom,current-boost-limit = <805>;
|
| D | tps65217-backlight.txt | 3 The TPS65217 chip contains a boost converter and current sinks which can be
|
| /Linux-v5.4/Documentation/usb/ |
| D | iuu_phoenix.rst | 40 boost:
41 overclock boost percent 100 to 500 (int)
57 - boost provide a way to overclock the reader ( my favorite :-) )
60 modprobe boost=195
84 use this settings to deduce de boost but is that feature
|
| /Linux-v5.4/drivers/usb/serial/ |
| D | iuu_phoenix.c | 38 static int boost = 100; variable
61 u32 boost; member
914 baud * priv->boost / 100, in iuu_set_termios()
985 if (boost < 100) in iuu_open()
986 boost = 100; in iuu_open()
987 priv->boost = boost; in iuu_open()
991 iuu_clk(port, IUU_CLK_3680000 * boost / 100); in iuu_open()
993 iuu_uart_baud(port, baud * boost / 100, &actual, in iuu_open()
997 iuu_clk(port, IUU_CLK_6000000 * boost / 100); in iuu_open()
1001 iuu_uart_baud(port, 16457 * boost / 100, &actual, in iuu_open()
[all …]
|
| /Linux-v5.4/Documentation/devicetree/bindings/ata/ |
| D | imx-sata.txt | 19 - fsl,transmit-boost-mdB : transmit boost level, in milli-decibels
|
| /Linux-v5.4/sound/pcmcia/vx/ |
| D | vxpocket.h | 37 void vx_set_mic_boost(struct vx_core *chip, int boost);
|
| /Linux-v5.4/tools/power/cpupower/ |
| D | ToDo | 5 - Try to read out boost states and frequencies on Intel
|
| /Linux-v5.4/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-distance-srf08 | 6 Show or set the gain boost of the amp, from 0-31 range.
|
| D | sysfs-bus-iio-proximity-as3935 | 14 Show or set the gain boost of the amp, from 0-31 range.
|
| D | sysfs-platform-asus-wmi | 45 Fan boost mode:
|
| /Linux-v5.4/Documentation/devicetree/bindings/phy/ |
| D | apm-xgene-phy.txt | 27 - apm,tx-boost-gain : Frequency boost AC (LSB 3-bit) and DC (2-bit)
|
| /Linux-v5.4/drivers/power/supply/ |
| D | bq2415x_charger.c | 726 int boost = 0; in bq2415x_set_mode() local
729 boost = 1; in bq2415x_set_mode()
736 if (!boost) in bq2415x_set_mode()
770 else if (boost) in bq2415x_set_mode()
891 int boost; in bq2415x_timer_work() local
907 boost = bq2415x_exec_command(bq, BQ2415X_BOOST_MODE_STATUS); in bq2415x_timer_work()
908 if (boost < 0) { in bq2415x_timer_work()
919 if (boost) { in bq2415x_timer_work()
|
| /Linux-v5.4/Documentation/admin-guide/pm/ |
| D | cpufreq.rst | 610 term "frequency boost" is used here for brevity to refer to all of those
613 The frequency boost mechanism may be either hardware-based or software-based.
620 The ``boost`` File in ``sysfs``
624 the "boost" setting for the whole system. It is not present if the underlying
625 scaling driver does not support the frequency boost mechanism (or supports it,
629 If the value in this file is 1, the frequency boost mechanism is enabled. This
634 permission to use the frequency boost mechanism (which still may never be used
637 If the value in this file is 0, the frequency boost mechanism is disabled and
645 The frequency boost mechanism is generally intended to help to achieve optimum
650 For this reason, many systems make it possible to disable the frequency boost
[all …]
|
| /Linux-v5.4/arch/arm64/boot/dts/exynos/ |
| D | exynos7-espresso.dts | 45 usb3drd_boost_5v: regulator-usb3drd-boost {
401 usb3drd_boost_en: usb3drd-boost-en {
411 vbus-boost-supply = <&usb3drd_boost_5v>;
|
| /Linux-v5.4/Documentation/devicetree/bindings/regulator/ |
| D | max77650-regulator.txt | 9 The device has a single LDO regulator and a SIMO buck-boost regulator with
|
| /Linux-v5.4/Documentation/devicetree/bindings/leds/ |
| D | leds-lp8860.txt | 4 driver with boost controller. It has 4 high-precision
|
