| /Linux-v5.4/Documentation/driver-api/usb/ |
| D | typec_bus.rst | 11 every alternate mode, so every alternate mode will need a custom driver.
13 USB Type-C bus allows binding a driver to the discovered partner alternate
16 :ref:`USB Type-C Connector Class <typec>` provides a device for every alternate
17 mode a port supports, and separate device for every alternate mode the partner
18 supports. The drivers for the alternate modes are bound to the partner alternate
19 mode devices, and the port alternate mode devices must be handled by the port
22 When a new partner alternate mode device is registered, it is linked to the
23 alternate mode device of the port that the partner is attached to, that has
24 matching SVID and mode. Communication between the port driver and alternate mode
27 The port alternate mode devices are used as a proxy between the partner and the
[all …]
|
| D | typec.rst | 22 the roles and alternate modes of ports, partners and cable plugs when the port
49 alternate mode will be the device that supports it, so for example an alternate
52 device named "mode<index>", for example /sys/class/typec/port0/<alternate
171 So ports, partners and cable plugs will register the alternate modes with their
200 alternate mode drivers for the mode, the two are always separated into their
214 Illustration of the muxes behind a connector that supports an alternate mode::
|
| /Linux-v5.4/Documentation/devicetree/bindings/pinctrl/ |
| D | renesas,rza1-pinctrl.txt | 8 function (port mode) or in alternate function mode.
9 Up to 8 different alternate function modes exist for each single pin.
41 (or a single) pin in some desired alternate function mode.
43 A few alternate function require special pin configuration flags to be
44 supplied along with the alternate function configuration number.
103 When a pin has to be configured in alternate function mode, use this
105 alternate function configuration number along with it.
107 alternate function they shall be specified as members of the same
110 (port where it sits on and pin number) and alternate function identifier
140 Pin #0 on port #3 is configured as alternate function #6.
[all …]
|
| D | renesas,rza2-pinctrl.txt | 6 function (port mode) or in alternate function mode.
7 Up to 8 different alternate function modes exist for each single pin.
44 (or a single) pin in some desired alternate function mode.
54 When a pin has to be configured in alternate function mode, use this
56 alternate function configuration number along with it.
58 alternate function they shall be specified as members of the same
61 (port where it sits on and pin number) and alternate function identifier
|
| D | renesas,rzn1-pinctrl.txt | 33 (or a single) pin in some desired alternate function mode.
106 When a pin has to be configured in alternate function mode, use this
108 alternate function configuration number along with it.
110 alternate function they shall be specified as members of the same
115 one of the alternate function identifiers defined in:
|
| D | pinctrl-vt8500.txt | 4 either a GPIO in, GPIO out or as an alternate function (I2C, SPI etc).
37 2: alternate
|
| D | cirrus,madera-pinctrl.txt | 5 Certain groups of GPIO pins also have an alternate function, normally as an
8 The set of available GPIOs, functions and alternate function groups differs
|
| /Linux-v5.4/drivers/media/usb/pwc/ |
| D | pwc-ctrl.c | 80 char alternate; /* USB alternate setting */ member
177 if (pEntry->alternate == 0) in set_video_mode_Nala()
192 pdev->valternate = pEntry->alternate; in set_video_mode_Nala()
235 if (pChoose->alternate != 0) in set_video_mode_Timon()
240 if (pChoose->alternate == 0) in set_video_mode_Timon()
255 pdev->valternate = pChoose->alternate; in set_video_mode_Timon()
286 if (pChoose->alternate != 0) in set_video_mode_Kiara()
291 if (pChoose->alternate == 0) in set_video_mode_Kiara()
306 pdev->valternate = pChoose->alternate; in set_video_mode_Kiara()
353 if (Nala_table[size][i].alternate) { in pwc_get_fps_Nala()
[all …]
|
| D | pwc-kiara.h | 24 char alternate; /* USB alternate interface */ member
|
| D | pwc-timon.h | 39 char alternate; /* USB alternate interface */ member
|
| /Linux-v5.4/Documentation/ABI/testing/ |
| D | sysfs-bus-typec | 27 Power Delivery command. Depending on the alternate mode, the
30 With some alternate modes (SVIDs), the mode index is assigned
32 alternate mode.
34 With other alternate modes, the mode index values are not
36 the mode index is not assigned, identifying the alternate mode
44 alternate mode.
|
| D | sysfs-class-watchdog | 82 system has booted from the alternate flash chip due to
84 alternate boot function was enabled with 'aspeed,alt-boot'
88 At alternate flash the 'access_cs0' sysfs node provides:
90 chip at CS0 after booting from the alternate
100 For alternate boot mode (booted from CS1 due to wdt2
|
| D | sysfs-driver-hid-logitech-lg4ff | 13 Description: Displays a set of alternate modes supported by a wheel. Each
56 alternate mode the wheel might be switched to.
|
| /Linux-v5.4/Documentation/ABI/obsolete/ |
| D | sysfs-class-typec | 9 alternate mode.
40 with the port alternate modes it can be used for disabling
41 support for specific alternate modes. Entering/exiting modes is
|
| /Linux-v5.4/Documentation/arm/pxa/ |
| D | mfp.rst | 14 Unlike the GPIO alternate function settings on PXA25x and PXA27x, a new MFP
47 To better understand the change from PXA25x/PXA27x GPIO alternate function
174 Bit 15: PULL_SEL - pull state controlled by selected alternate function
177 Bit 0 - 2: AF_SEL - alternate function selection, 8 possibilities, from 0-7
250 * alternate function = 0,
255 * MFP_CFG - default MFPR value with alternate function
256 * MFP_CFG_DRV - default MFPR value with alternate function and
258 * MFP_CFG_LPM - default MFPR value with alternate function and
260 * MFP_CFG_X - default MFPR value with alternate function,
268 which reads GPIO94 can be configured as SSP3_RXD, with alternate function
|
| /Linux-v5.4/Documentation/devicetree/bindings/phy/ |
| D | phy-cpcap-usb.txt | 14 pinctrl: Optional alternate pin modes for the PHY
16 mode-gpios: Optional GPIOs for configuring alternate modes
|
| /Linux-v5.4/drivers/usb/usbip/ |
| D | stub_rx.c | 106 __u16 alternate; in tweak_set_interface_cmd() local
111 alternate = le16_to_cpu(req->wValue); in tweak_set_interface_cmd()
115 interface, alternate); in tweak_set_interface_cmd()
117 ret = usb_set_interface(urb->dev, interface, alternate); in tweak_set_interface_cmd()
121 interface, alternate, ret); in tweak_set_interface_cmd()
125 interface, alternate); in tweak_set_interface_cmd()
|
| /Linux-v5.4/drivers/media/usb/cpia2/ |
| D | cpia2_v4l.c | 46 static int alternate = DEFAULT_ALT; variable
47 module_param(alternate, int, 0);
48 MODULE_PARM_DESC(alternate, "USB Alternate (" __stringify(USBIF_ISO_1) "-"
997 cam->params.camera_state.stream_mode = alternate; in reset_camera_struct_v4l()
1100 cpia2_usb_alt.def = alternate; in cpia2_register_camera()
1184 if(alternate < USBIF_ISO_1 || alternate > USBIF_ISO_6) { in check_parameters()
1185 alternate = DEFAULT_ALT; in check_parameters()
1186 LOG("alternate specified is invalid, using %d\n", alternate); in check_parameters()
1196 num_buffers, buffer_size, alternate); in check_parameters()
|
| /Linux-v5.4/Documentation/driver-api/soundwire/ |
| D | stream.rst | 260 alternate bank (bank currently unused). Port(s) are enabled for the
261 already active stream(s) on the alternate bank (bank currently unused).
264 (4) Once all the values are programmed, Bus initiates switch to alternate
289 in alternate bank (bank currently unused). It includes programming of
293 enabled on alternate bank (bank currently unused) by programming
296 (3) Once all the values are programmed, Bus initiates switch to alternate
318 disabled on alternate bank (bank currently unused) by programming
322 into alternate bank (bank currently unused).
324 (3) Once all the values are programmed, Bus initiates switch to alternate
|
| /Linux-v5.4/Documentation/admin-guide/ |
| D | devices.rst | 126 (the use of the alternate callout devices is deprecated).
205 names, the primary or callin device and the alternate or callout one.
216 The alternate devices provide for kernel-based exclusion and somewhat
230 that a lock file be installed with the corresponding alternate
236 3. The alternate device name (``/var/lock/LCK..cua2``)
243 to create lock files for the corresponding alternate device names
245 port TTY, for which no alternate device would exist.
|
| /Linux-v5.4/Documentation/devicetree/bindings/cpufreq/ |
| D | cpufreq-qcom-hw.txt | 21 Definition: must be "xo", "alternate".
168 clock-names = "xo", "alternate";
|
| /Linux-v5.4/drivers/staging/iio/Documentation/ |
| D | sysfs-bus-iio-ad7192 | 8 alternate cycles, to eliminate DC errors.
|
| /Linux-v5.4/Documentation/media/v4l-drivers/ |
| D | cpia2.rst | 71 alternate USB Alternate (2-7, default 7)
98 The maximum image size depends on the alternate you choose, and the
108 At low alternate settings, the compression engine may not be able to
113 any alternate at frame rates down to 15fps. For lower frame rates, it may
|
| /Linux-v5.4/arch/arm/boot/dts/ |
| D | omap3-gta04a3.dts | 14 /* alternate accelerometer that might be installed on some GTA04A3 boards */
|
| /Linux-v5.4/Documentation/devicetree/bindings/clock/ |
| D | qcom,spmi-clkdiv.txt | 4 These clocks are typically wired through alternate functions on
|
