| /Linux-v5.4/drivers/pinctrl/ |
| D | pinctrl-lpc18xx.c | 266 LPC_P(2,5, SGPIO, CTIN, USB1, ADCTRIG, GPIO, R, TIMER3, USB0, 0, HD);
276 LPC_P(3,1, I2S0_TX_WS, I2S0_RX_WS,CAN0,USB1,GPIO, R, LCD, R, 0, ND);
277 LPC_P(3,2, I2S0_TX_SDA, I2S0_RX_SDA,CAN0,USB1,GPIO, R, LCD, R, 0, ND);
327 LPC_P(8,3, GPIO, USB1, R, LCD, LCD_ALT, R, R, TIMER0, 0, ND);
328 LPC_P(8,4, GPIO, USB1, R, LCD, LCD_ALT, R, R, TIMER0, 0, ND);
329 LPC_P(8,5, GPIO, USB1, R, LCD, LCD_ALT, R, R, TIMER0, 0, ND);
330 LPC_P(8,6, GPIO, USB1, R, LCD, LCD_ALT, R, R, TIMER0, 0, ND);
331 LPC_P(8,7, GPIO, USB1, R, LCD, LCD_ALT, R, R, TIMER0, 0, ND);
332 LPC_P(8,8, R, USB1, R, R, R, R,CGU_OUT, I2S1, 0, ND);
336 LPC_P(9,3, GPIO, MCTRL, USB1, R, R, ENET, SGPIO, UART3, 0, ND);
[all …]
|
| /Linux-v5.4/drivers/media/usb/b2c2/ |
| D | Kconfig | 6 Support for the Air/Sky/Cable2PC USB1.1 box (DVB/ATSC) by Technisat/B2C2,
|
| /Linux-v5.4/include/dt-bindings/clock/ |
| D | xlnx-zynqmp-clk.h | 48 #define USB1 36 macro
|
| /Linux-v5.4/Documentation/media/dvb-drivers/ |
| D | dvb-usb.rst | 106 - distorted streaming is gone for USB1.1 devices
293 USB1.1 Bandwidth limitation
296 A lot of the currently supported devices are USB1.1 and thus they have a
302 frequency simply does not work very well. This applies to all USB1.1
|
| /Linux-v5.4/Documentation/devicetree/bindings/phy/ |
| D | brcm,brcmstb-usb-phy.txt | 12 - PHY_TYPE_USB2 for USB1.1/2.0 PHY
|
| /Linux-v5.4/Documentation/devicetree/bindings/reset/ |
| D | nxp,lpc1850-rgu.txt | 24 18 USB1
|
| /Linux-v5.4/arch/sh/kernel/cpu/sh4a/ |
| D | setup-sh7724.c | 864 USB0, USB1, enumerator
927 INTC_VECT(USB1, 0xA40),
1004 INTC_GROUP(USB, USB0, USB1),
1042 { 0, 0, 0, CMT, 0, USB1, USB0, 0 } },
|
| D | setup-sh7757.c | 797 USB0, USB1, enumerator
863 INTC_VECT(USB1, 0x920),
972 IRQ9, IRQ8, SCIF1, SCIF0, USB0, 0, 0, USB1,
1072 { INT2PRI12, 0, 32, 8, { USB0, 0, IRQ15, USB1 } },
|
| /Linux-v5.4/arch/powerpc/boot/dts/ |
| D | pdm360ng.dts | 126 /* USB1 using external ULPI PHY */
|
| D | mpc5125twr.dts | 228 // disable USB1 port
|
| D | sequoia.dts | 148 USB1: usb@e0000400 { label
|
| D | mpc5121.dtsi | 292 /* USB1 using external ULPI PHY */
|
| D | canyonlands.dts | 173 USB1: usb@bffd0000 { label
|
| /Linux-v5.4/drivers/media/usb/dvb-usb/ |
| D | Kconfig | 7 USB1.1 and USB2.0 DVB devices.
261 tristate "Afatech AF9005 DVB-T USB1.1 support"
266 Say Y here to support the Afatech AF9005 based DVB-T USB1.1 receiver
|
| /Linux-v5.4/arch/arm/boot/dts/ |
| D | sun8i-h2-plus-orangepi-r1.dts | 81 * RTL8152B USB-Ethernet adapter is connected to USB1,
|
| D | gemini.dtsi | 421 * This will claim pins for USB0 and USB1 at the same
423 * some reason have a system using USB1 at 96000000 but
|
| D | sun4i-a10-pcduino.dts | 197 usb1_vbus-supply = <®_vcc5v0>; /* USB1 VBUS is always on */
|
| D | dove-cm-a510.dtsi | 67 * U4: 2 additional USB2.0 host ports (via USB1)
|
| D | sun8i-a33-sinlinx-sina33.dts | 273 usb1_vbus-supply = <®_vcc5v0>; /* USB1 VBUS is always on */
|
| D | am335x-pepper.dts | 592 /* USB1 Over-Current (active low) */
|
| D | imx6qdl-kontron-samx6i.dtsi | 783 /* USB1/2 via hub */
|
| /Linux-v5.4/Documentation/devicetree/bindings/clock/ |
| D | lpc1850-cgu.txt | 49 3 BASE_USB1_CLK Base clock for USB1
|
| /Linux-v5.4/drivers/media/usb/dvb-usb-v2/ |
| D | Kconfig | 7 USB1.1 and USB2.0 DVB devices.
|
| /Linux-v5.4/drivers/regulator/ |
| D | mc13892-regulator.c | 293 MC13892_FIXED_DEFINE(VUSB, vusb, USB1, mc13892_vusb),
|
| /Linux-v5.4/drivers/clk/nxp/ |
| D | clk-lpc18xx-cgu.c | 226 LPC1XX_CGU_BASE_CLK(USB1, base_all_src_ids, 0),
|
