Searched refs:LPM (Results 1 – 17 of 17) sorted by relevance
128 in to a xHCI host which support link PM, it will perform a LPM129 test; if the test is passed and host supports USB2 hardware LPM130 (xHCI 1.0 feature), USB2 hardware LPM will be enabled for the133 or disable) indicating whether or not USB2 hardware LPM is146 the check is passed and the host supports USB3 hardware LPM,147 USB3 hardware LPM will be enabled for the device and the USB151 or not USB3 hardware LPM U1 or U2 is enabled for the device.245 Some USB3.0 devices are not friendly to USB3 LPM. usb3_lpm_permit256 USB 2.0 devices may support hardware link power management (LPM)258 tuning the timeout for L1 inactivity timer (LPM timer), e.g.[all …]
7 the chip including L2 FDB, L3 LPM, ECMP and more. The KVD
26 - usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM27 - usb3-lpm-capable: determines if platform is USB3 LPM capable
40 - usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM41 - usb3-lpm-capable: determines if platform is USB3 LPM capable
40 - snps,usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM41 - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable47 - snps,has-lpm-erratum: true when DWC3 was configured with LPM Erratum enabled48 - snps,lpm-nyet-threshold: LPM NYET threshold
50 - usb3-lpm-capable : supports USB3.0 LPM108 - usb3-lpm-capable : supports USB3.0 LPM
76 [ 1815.999595] usb 4-3: LPM exit latency is zeroed, disabling LPM.144 [ 79.475003] usb 2-2.1: LPM exit latency is zeroed, disabling LPM.
529 enabling hardware LPM, the host can automatically put the device into533 The user interface for controlling hardware LPM is located in the540 When a USB2 device which support LPM is plugged to a541 xHCI host root hub which support software LPM, the542 host will run a software LPM test for it; if the device544 supports USB2 hardware LPM, this file will show up and545 driver will enable hardware LPM for the device. You547 USB2 hardware LPM manually. This is for test purpose mainly.556 supports USB3 hardware LPM, USB3 hardware LPM will be559 indicating whether or not USB3 hardware LPM U1 or U2
172 between HPM and LPM); not available on boost type176 to as NPM. HPM consumes more ground current than LPM, but182 0 = Set initial mode to low power mode (LPM).
6 - lpm-gpios: GPIO for LPM pin. Note that this GPIO *must* remain high during
54 PESEL = 0x00000008, LPM = 0x00000004, BEM = 0x00000001, enumerator
47 LOGITECH LPM-SCSI2E
89 * non-LPM pulled output, the same configuration could probably be used.
32 * HACK: until we have an LPM driver, we'll use an
312 does a longest prefix match (LPM) on FIB entries matching route prefix and
99 Select the Default SATA Link Power Management (LPM) policy to use
1123 NIC0800 "PC-LPM-16 Low Power Multi-function Board"
