| /Linux-v5.4/arch/parisc/include/asm/ |
| D | led.h | 11 #define LED1 0x02 macro
15 #define LED_LAN_RCV LED1 /* for LAN receive activity */
|
| /Linux-v5.4/drivers/leds/ |
| D | leds-bd2802.c | 39 LED1, enumerator
211 value = (id == LED1) ? LED_CTL(1, 0) : LED_CTL(0, 1); in bd2802_update_state()
220 reg = bd2802_get_reg_addr(LED1, RED, BD2802_REG_HOURSETUP); in bd2802_configure()
236 enum led_ids other_led = (id == LED1) ? LED2 : LED1; in bd2802_enable()
240 if (id == LED1) in bd2802_enable()
547 BD2802_CONTROL_RGBS(led1r, LED1, RED);
548 BD2802_CONTROL_RGBS(led1g, LED1, GREEN);
549 BD2802_CONTROL_RGBS(led1b, LED1, BLUE);
|
| /Linux-v5.4/drivers/iio/health/ |
| D | afe4404.c | 99 LED1, enumerator
108 [LED1] = AFE440X_LED1VAL,
117 [LED1] = F_ILED1,
123 [LED1] = F_OFFDAC_LED1,
131 AFE440X_INTENSITY_CHAN(LED1, BIT(IIO_CHAN_INFO_OFFSET)),
138 AFE440X_CURRENT_CHAN(LED1),
|
| D | afe4403.c | 80 LED1, enumerator
89 [LED1] = AFE440X_LED1VAL,
97 [LED1] = F_ILED1,
104 AFE440X_INTENSITY_CHAN(LED1, 0),
110 AFE440X_CURRENT_CHAN(LED1),
|
| /Linux-v5.4/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-health-afe440x | 11 3 -> LED1
13 Note that channels 5 and 6 represent LED2-ALED2 and LED1-ALED1
|
| /Linux-v5.4/Documentation/firmware-guide/acpi/dsd/ |
| D | leds.rst | 46 Package () { "led@1", LED1 },
59 Name (LED1, Package () {
87 LED1 Second LED
|
| /Linux-v5.4/arch/arm/boot/dts/ |
| D | imx7d-mba7.dts | 42 /* LED1: Link/Activity, LED2: error */
44 /* active low, LED1/2 driven by phy */
|
| D | s3c6410-mini6410.dts | 138 label = "LED1";
|
| D | imx7-mba7.dtsi | 217 /* LED1: Link/Activity, LED2: Error */
219 /* Active low, LED1 and LED2 driven by phy */
|
| D | sun4i-a10-cubieboard.dts | 80 gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; /* LED1 */
|
| D | sun7i-a20-bananapi.dts | 244 "LED1", "", "", "", "", "", "", "",
|
| D | omap3-devkit8000-common.dtsi | 20 gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>; /* 186 -> LED1 */
|
| D | sh73a0-kzm9g.dts | 88 label = "LED1";
|
| D | imx6q-marsboard.dts | 307 MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x1b0b1 /* LED1 */
|
| /Linux-v5.4/include/linux/mfd/ |
| D | tps65010.h | 112 #define LED1 1 macro
|
| /Linux-v5.4/Documentation/devicetree/bindings/leds/ |
| D | leds-lm3692x.txt | 24 1 - Will enable the LED1 sync
|
| D | leds-mt6323.txt | 51 label = "LED1";
|
| /Linux-v5.4/Documentation/devicetree/bindings/leds/backlight/ |
| D | lp855x.txt | 40 /* 4 output LED1 string enabled */
|
| /Linux-v5.4/arch/arm64/boot/dts/marvell/ |
| D | armada-8040-clearfog-gt-8k.dts | 146 * [40,41] LED0 and LED1
362 * LED1 - on: link, blink: activity
|
| /Linux-v5.4/drivers/net/wireless/zydas/zd1211rw/ |
| D | zd_chip.c | 336 chip->link_led = ((value >> 4) & 1) ? LED1 : LED2; in read_pod()
350 chip->link_led == LED1 ? 1 : 2, in read_pod()
1321 other_led = chip->link_led == LED1 ? LED2 : LED1; in zd_chip_control_leds()
1326 ioreqs[1].value = v[1] & ~(LED1|LED2); in zd_chip_control_leds()
|
| /Linux-v5.4/drivers/usb/gadget/udc/ |
| D | net2272.h | 369 #define LED1 25 macro
|
| /Linux-v5.4/arch/arm/mach-omap1/ |
| D | board-osk.c | 216 tps65010_set_led(LED1, BLINK); in osk_tps_setup()
|
| /Linux-v5.4/drivers/pinctrl/cirrus/ |
| D | pinctrl-lochnagar.c | 206 LN1_PIN_MUX(LED1, "led1");
308 LN1_PIN(LED1), LN1_PIN(LED2),
646 LN1_GROUP_PIN(LED1), LN1_GROUP_PIN(LED2),
|
| /Linux-v5.4/arch/arm64/boot/dts/actions/ |
| D | s900-bubblegum-96.dts | 93 "LED1", /* GPIO_20 */
|
| /Linux-v5.4/arch/arm64/boot/dts/renesas/ |
| D | r8a774c0-cat874.dts | 48 label = "LED1";
|
