| /Linux-v5.4/drivers/video/fbdev/omap/ |
| D | lcd_h3.c | 23 r = tps65010_set_gpio_out_value(GPIO1, HIGH); in h3_panel_enable()
37 r = tps65010_set_gpio_out_value(GPIO1, LOW); in h3_panel_disable()
|
| /Linux-v5.4/Documentation/devicetree/bindings/gpio/ |
| D | gpio-axp209.txt | 60 not force GPIO1 and GPIO2 to be in gpio_in function as well).
67 GPIO1 | gpio_in, gpio_out, ldo, adc
75 GPIO1 | gpio_in, gpio_out, ldo
|
| /Linux-v5.4/Documentation/devicetree/bindings/mfd/ |
| D | max77620.txt | 34 and power-down delays (sequencing). GPIO1, GPIO2, and GPIO3 can be programmed
46 Each regulator, GPIO1, GPIO2, GPIO3, and 32KHz clock has a flexible power
117 1: Enables POK(Power OK) to control nRST_IO and GPIO1
121 If POK mapping is enabled for GPIO1/nRST_IO then,
122 GPIO1/nRST_IO pins are HIGH only if all rails
125 control) then, GPIO1/nRST_IO goes LOW.
|
| /Linux-v5.4/drivers/media/usb/dvb-usb/ |
| D | dib07x0.h | 7 GPIO1 = 2, enumerator
|
| /Linux-v5.4/arch/sh/kernel/cpu/sh4a/ |
| D | setup-shx3.c | 184 GPIO0, GPIO1, GPIO2, GPIO3, enumerator
231 INTC_VECT(GPIO0, 0xe40), INTC_VECT(GPIO1, 0xe60),
266 DU, GPIO3, GPIO2, GPIO1, GPIO0, PAM, 0, 0,
302 GPIO2, GPIO1, GPIO0, IRM } },
|
| D | setup-sh7786.c | 494 GPIO0, GPIO1, enumerator
539 INTC_VECT(GPIO0, 0xea0), INTC_VECT(GPIO1, 0xec0),
609 HSPI, GPIO0, GPIO1, Thermal,
649 GPIO1, Thermal } },
|
| /Linux-v5.4/drivers/pinctrl/ |
| D | pinctrl-xway.c | 117 MFP_XWAY(GPIO1, GPIO, EXIN, NONE, NONE),
203 static const unsigned xway_exin_pin_map[] = {GPIO0, GPIO1, GPIO2, GPIO39, GPIO46, GPIO9};
206 static const unsigned pins_exin1[] = {GPIO1};
353 MFP_XWAY(GPIO1, GPIO, STP, DFE, EBU),
394 static const unsigned ase_pins_stp[] = {GPIO1, GPIO2, GPIO3};
399 static const unsigned ase_pins_dfe_led0[] = {GPIO1};
481 MFP_XWAY(GPIO1, GPIO, EXIN, CBUS, MII),
514 static const unsigned danube_exin_pin_map[] = {GPIO0, GPIO1, GPIO2};
517 static const unsigned danube_pins_exin1[] = {GPIO1};
656 MFP_XWAY(GPIO1, GPIO, EXIN, CBUS, SIN),
[all …]
|
| D | pinctrl-lantiq.h | 107 GPIO1, enumerator
|
| /Linux-v5.4/drivers/usb/host/ |
| D | ohci-omap.c | 63 #define GPIO1 1 macro
103 tps65010_set_gpio_out_value(GPIO1, LOW); in omap_ohci_transceiver_power()
110 tps65010_set_gpio_out_value(GPIO1, HIGH); in omap_ohci_transceiver_power()
|
| /Linux-v5.4/arch/powerpc/boot/dts/ |
| D | warp.dts | 253 GPIO1: gpio@ef600c00 { label
263 gpios = <&GPIO1 0 0>;
267 gpios = <&GPIO1 1 0>;
|
| /Linux-v5.4/drivers/net/wireless/realtek/rtl818x/rtl8187/ |
| D | rfkill.c | 26 gpio = rtl818x_ioread8(priv, &priv->map->GPIO1); in rtl8187_is_radio_enabled()
|
| /Linux-v5.4/include/linux/mfd/ |
| D | tps65010.h | 117 #define GPIO1 1 macro
|
| /Linux-v5.4/Documentation/devicetree/bindings/interrupt-controller/ |
| D | rda,8810pl-intc.txt | 30 12: GPIO1
|
| D | brcm,bcm2835-armctrl-ic.txt | 97 18: GPIO1
|
| /Linux-v5.4/Documentation/devicetree/bindings/sound/ |
| D | rt5668.txt | 21 0: using GPIO1 pin as dmic1 clock pin
|
| D | rt5682.txt | 21 0: using GPIO1 pin as dmic1 clock pin
|
| D | rt5677.txt | 39 Select 0 ~ 3 as OFF, GPIO1, GPIO2 and GPIO3 respectively.
|
| D | rt5640.txt | 38 1: Use GPIO1 for jack-detect
|
| /Linux-v5.4/Documentation/devicetree/bindings/pinctrl/ |
| D | ste,nomadik.txt | 119 pins = "GPIO1", "GPIO3";
129 pins = "GPIO1";
|
| /Linux-v5.4/arch/arm/boot/dts/ |
| D | bcm2835-rpi-cm1-io1.dts | 21 "GPIO1",
|
| D | bcm2837-rpi-cm3-io3.dts | 21 "GPIO1",
|
| /Linux-v5.4/Documentation/arm/ |
| D | netwinder.rst | 32 0x0338 GPIO1
|
| /Linux-v5.4/Documentation/devicetree/bindings/display/bridge/ |
| D | ti,sn65dsi86.txt | 34 - suspend-gpios: specification for GPIO1 pin on bridge (active low)
|
| /Linux-v5.4/arch/arm/mach-pxa/ |
| D | mfp-pxa2xx.h | 62 #define GPIO1_GPIO MFP_CFG_IN(GPIO1, AF0)
|
| D | pxa930.c | 24 MFP_ADDR(GPIO1, 0x02dc),
|
