Searched refs:CRT (Results 1 – 15 of 15) sorted by relevance
| /Linux-v5.4/Documentation/fb/ |
| D | viafb.rst | 16 Device: CRT, LCD, DVI
20 CRT:
42 viafb_active_dev=CRT+DVI viafb_dvi_port=DVP1
109 This option is used to specify active devices.(CRT, DVI, CRT+LCD...)
121 To enable two devices, such as CRT+DVI::
123 modprobe viafb viafb_active_dev=CRT+DVI;
127 modprobe viafb viafb_active_dev=CRT+DVI
131 modprobe viafb viafb_active_dev=DVI+CRT...
135 If CRT is primary and DVI is secondary, we should use::
137 modprobe viafb viafb_active_dev=CRT+DVI viafb_SAMM_ON=1...
[all …]
|
| D | modedb.rst | 91 The GTF is limited by the fact that it is designed mainly for CRT displays.
97 The CVT addresses these limitations. If used with CRT's, the formula used
104 new CRT displays and probably with most flatpanels, if 'reduced blanking'
|
| /Linux-v5.4/Documentation/ABI/testing/ |
| D | sysfs-platform-eeepc-laptop | 8 - 2 = CRT
9 - 3 = LCD+CRT
|
| D | sysfs-platform-asus-laptop | 10 ||`-- CRT
14 - 3 (0011b) CRT+LCD.
|
| /Linux-v5.4/drivers/gpu/drm/nouveau/nvkm/engine/disp/ |
| D | dacgf119.c | 41 case 0: state->proto = CRT; break; in gf119_dac_state()
|
| D | dacnv50.c | 92 case 0: state->proto = CRT; break; in nv50_dac_state()
|
| D | ior.h | 26 CRT, enumerator
|
| D | outp.c | 64 case DCB_OUTPUT_ANALOG: *type = DAC; return CRT; in nvkm_outp_xlat()
|
| /Linux-v5.4/arch/sh/cchips/ |
| D | Kconfig | 17 CRT color controller, IrDA up to 4 Mbps, and a
|
| /Linux-v5.4/Documentation/admin-guide/laptops/ |
| D | asus-laptop.rst | 123 | Bin | Val | DVI | TV | CRT | LCD |
|
| D | thinkpad-acpi.rst | 654 LCD, CRT or DVI (if available). The following commands are available::
|
| /Linux-v5.4/drivers/video/fbdev/ |
| D | cirrusfb.c | 349 CRT, enumerator
2830 case CRT: in cirrusfb_dbg_print_regs()
2864 cirrusfb_dbg_print_regs(info, regbase, CRT, in cirrusfb_dbg_reg_dump()
|
| D | Kconfig | 1934 Frame buffer driver for the CRT and LCD controllers in the Silicon
|
| /Linux-v5.4/drivers/pinctrl/tegra/ |
| D | pinctrl-tegra20.c | 2056 MUX_PG(crtp, CRT, RSVD2, RSVD3, RSVD4, 0x20, 14, 0x98, 20, 0xa4, 24),
2113 MUX_PG(lm1, DISPLAYA, DISPLAYB, RSVD3, CRT, 0x1c, 25, 0x90, 28, -1, -1),
|
| D | pinctrl-tegra30.c | 2348 …PINGROUP(crt_hsync_pv6, CRT, RSVD2, RSVD3, RSVD4, 0x311c, N, …
2349 …PINGROUP(crt_vsync_pv7, CRT, RSVD2, RSVD3, RSVD4, 0x3120, N, …
|
