| /Linux-v5.15/drivers/leds/ |
| D | leds-wm8350.c | 147 int uA; in wm8350_led_set() local
163 uA = (led->max_uA_index * led->value) / LED_FULL; in wm8350_led_set()
165 BUG_ON(uA >= ARRAY_SIZE(isink_cur)); in wm8350_led_set()
167 ret = regulator_set_current_limit(led->isink, isink_cur[uA], in wm8350_led_set()
168 isink_cur[uA]); in wm8350_led_set()
171 isink_cur[uA], ret); in wm8350_led_set()
|
| /Linux-v5.15/Documentation/devicetree/bindings/rtc/ |
| D | rtc-palmas.txt | 17 backup battery. Device supports the < 100uA and > 100uA charging.
18 The high current will be > 100uA. Absence of this property will
19 charge battery to lower current i.e. < 100uA.
|
| /Linux-v5.15/Documentation/devicetree/bindings/usb/ |
| D | usb251xb.txt | 52 attached peripheral (range: 0 - 100000 uA, default 1000 uA)
56 attached peripheral (range: 0 - 510000 uA, default 100000 uA)
60 attached peripheral (range: 0 - 100000 uA, default 1000 uA)
64 attached peripheral (range: 0 - 510000 uA, default 100000 uA)
|
| /Linux-v5.15/arch/arm64/boot/dts/freescale/ |
| D | imx8mq-librem5-r2.dts | 17 ti,charge-current = <1600000>; /* uA */
18 ti,termination-current = <66000>; /* uA */
|
| D | imx8mq-librem5-r4.dts | 25 ti,charge-current = <1500000>; /* uA */
26 ti,termination-current = <144000>; /* uA */
|
| D | imx8mq-librem5-r3.dts | 27 ti,charge-current = <1500000>; /* uA */
28 ti,termination-current = <144000>; /* uA */
|
| D | imx8mq-librem5.dtsi | 983 ti,precharge-current = <130000>; /* uA */
986 ti,boost-max-current = <500000>; /* uA */
|
| /Linux-v5.15/Documentation/devicetree/bindings/sound/ |
| D | cs43130.txt | 24 1 = 7.5uA
25 2 = 12.5uA
26 3 = 15uA
|
| D | cs35l33.txt | 35 The range starts at 1850000uA and goes to a maximum of 3600000uA
36 with a step size of 15625uA. The default is 2500000uA.
|
| /Linux-v5.15/Documentation/devicetree/bindings/mfd/ |
| D | as3711.txt | 15 - su1-max-uA : maximum current
20 - su1-max-uA : maximum current
66 su2-max-uA = <36000>;
|
| D | max14577.txt | 24 - maxim,fast-charge-uamp : Current in uA for Fast Charge;
28 - maxim,eoc-uamp : Current in uA for End-Of-Charge mode;
|
| D | max77693.txt | 67 in uA (current from battery to system).
|
| /Linux-v5.15/drivers/remoteproc/ |
| D | qcom_q6v5_mss.c | 123 int uA; member
129 int uA; member
242 regs[i].uA = reg_res[i].uA; in q6v5_regulator_init()
266 if (regs[i].uA > 0) { in q6v5_regulator_enable()
268 regs[i].uA); in q6v5_regulator_enable()
289 if (regs[i].uA > 0) in q6v5_regulator_enable()
307 if (regs[i].uA > 0) in q6v5_regulator_disable()
1956 .uA = 100000,
1987 .uA = 100000,
1998 .uA = 100000,
[all …]
|
| /Linux-v5.15/Documentation/devicetree/bindings/leds/ |
| D | leds-lm3532.txt | 66 bank. The range is from 5000uA-29800uA in increments
67 of 800uA.
|
| D | leds-lm36274.txt | 6 the I2C bus and/or controlled via a logic level PWM input from 60 uA to 30 mA.
|
| /Linux-v5.15/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-adc-mt6360 | 43 Calculating with scale and offset returns voltage in uA
50 Calculating with scale and offset returns voltage in uA
|
| D | sysfs-class-power | 702 than 1uA. Note that on some devices/systems this disconnects the battery
|
| /Linux-v5.15/Documentation/devicetree/bindings/regulator/ |
| D | qcom,spmi-regulator.txt | 282 0 = 0.05 uA
283 1 = 0.25 uA
284 2 = 0.55 uA
285 3 = 0.75 uA
|
| D | max77802.txt | 61 3: Low Power which reduces the quiescent current down to only 1uA
|
| /Linux-v5.15/Documentation/devicetree/bindings/pinctrl/ |
| D | meson,pinctrl.txt | 62 - drive-strength-microamp: Drive strength for the specified pins in uA.
|
| /Linux-v5.15/drivers/regulator/ |
| D | wm8350-regulator.c | 835 static unsigned int get_mode(int uA, const struct wm8350_dcdc_efficiency *eff) in get_mode() argument
840 if (uA >= eff[i].uA_load_min && uA <= eff[i].uA_load_max) in get_mode()
|
| D | core.c | 771 int uA = 0; in requested_microamps_show() local
776 uA += regulator->uA_load; in requested_microamps_show()
779 return sprintf(buf, "%d\n", uA); in requested_microamps_show()
|
| /Linux-v5.15/arch/arm/boot/dts/ |
| D | imx6qdl-cubox-i.dtsi | 197 * leaving it as a pull-up, even if it is just 10uA.
|
| /Linux-v5.15/Documentation/userspace-api/media/v4l/ |
| D | ext-ctrls-flash.rst | 133 independent of the flash LED. The unit should be microamps (uA) if
|
| /Linux-v5.15/drivers/staging/greybus/Documentation/ |
| D | sysfs-bus-greybus | 60 Current measurement of the interface in microamps (uA)
|
