| /Linux-v5.15/arch/arm/boot/dts/ |
| D | ste-href520-tvk.dts | 42 /* VMMCI level-shifter enable */
47 /* VMMCI level-shifter voltage select */
|
| D | ste-hrefv60plus-tvk.dts | 43 /* VMMCI level-shifter enable */
48 /* VMMCI level-shifter voltage select */
|
| D | ste-hrefv60plus-stuib.dts | 62 /* VMMCI level-shifter enable */
67 /* VMMCI level-shifter voltage select */
|
| D | imx6q-logicpd.dts | 109 regulator-always-on; /* Without this, the level shifter on HDMI doesn't turn on */
|
| D | am335x-bonegreen-wireless.dts | 115 /* On the BBGW this pin is routed through the level shifter (U21) that */
|
| D | ste-snowball.dts | 515 /* VMMCI level-shifter enable */
520 /* VMMCI level-shifter voltage select */
|
| D | omap3-evm-processor-common.dtsi | 195 * for bus switch SN74CB3Q3384A, level-shifter SN74AVC16T245DGGR, and 1.8V.
|
| /Linux-v5.15/Documentation/devicetree/bindings/display/ti/ |
| D | ti,tpd12s015.txt | 1 TPD12S015 HDMI level shifter and ESD protection chip
|
| D | ti,omap-dss.txt | 88 shifter). The video pipelines for the connectors are formed as follows:
|
| /Linux-v5.15/drivers/net/ethernet/mellanox/mlx5/core/steering/ |
| D | dr_ste.h | 174 u8 shifter,
179 u8 shifter,
|
| D | dr_ste.c | 559 u8 shifter, in mlx5dr_ste_set_action_set() argument
564 hw_field, shifter, length, data); in mlx5dr_ste_set_action_set()
570 u8 shifter, in mlx5dr_ste_set_action_add() argument
575 hw_field, shifter, length, data); in mlx5dr_ste_set_action_add()
|
| D | dr_ste_v1.c | 802 u8 shifter, in dr_ste_v1_set_action_set() argument
806 shifter += MLX5_MODIFY_HEADER_V1_QW_OFFSET; in dr_ste_v1_set_action_set()
809 MLX5_SET(ste_double_action_set_v1, d_action, destination_left_shifter, shifter); in dr_ste_v1_set_action_set()
816 u8 shifter, in dr_ste_v1_set_action_add() argument
820 shifter += MLX5_MODIFY_HEADER_V1_QW_OFFSET; in dr_ste_v1_set_action_add()
823 MLX5_SET(ste_double_action_add_v1, d_action, destination_left_shifter, shifter); in dr_ste_v1_set_action_add()
|
| D | dr_ste_v0.c | 543 u8 shifter, in dr_ste_v0_set_action_set() argument
550 MLX5_SET(dr_action_hw_set, hw_action, destination_left_shifter, shifter); in dr_ste_v0_set_action_set()
557 u8 shifter, in dr_ste_v0_set_action_add() argument
564 MLX5_SET(dr_action_hw_set, hw_action, destination_left_shifter, shifter); in dr_ste_v0_set_action_add()
|
| D | dr_types.h | 298 u8 shifter,
304 u8 shifter,
|
| /Linux-v5.15/arch/microblaze/ |
| D | Kconfig.platform | 19 on MicroBlaze systems without a barrel shifter.
|
| /Linux-v5.15/arch/arm64/boot/dts/xilinx/ |
| D | zynqmp-zc1751-xm015-dc1.dts | 119 /* SD1 with level shifter */
|
| D | zynqmp-zcu104-revA.dts | 202 /* SD1 with level shifter */
|
| D | zynqmp-zcu104-revC.dts | 258 /* SD1 with level shifter */
|
| D | zynqmp-zcu100-revC.dts | 251 /* SD0 only supports 3.3V, no level shifter */
|
| D | zynqmp-zcu111-revA.dts | 571 /* SD1 with level shifter */
|
| /Linux-v5.15/Documentation/devicetree/bindings/media/ |
| D | cec-gpio.txt | 33 15 aka BCM22 (some level shifter is needed for the HPD and 5V lines!):
|
| /Linux-v5.15/drivers/video/fbdev/omap2/omapfb/displays/ |
| D | Kconfig | 17 tristate "TPD12S015 HDMI ESD protection and level shifter"
|
| /Linux-v5.15/Documentation/translations/zh_CN/maintainer/ |
| D | pull-requests.rst | 91 was a need for a new set of relativity shifter drivers to
|
| /Linux-v5.15/drivers/pinctrl/bcm/ |
| D | pinctrl-bcm2835.c | 1051 u32 shifter; in bcm2711_pull_config_set() local
1056 shifter = PUD_2711_REG_SHIFT(pin); in bcm2711_pull_config_set()
1059 value &= ~(PUD_2711_MASK << shifter); in bcm2711_pull_config_set()
1060 value |= (arg << shifter); in bcm2711_pull_config_set()
|
| /Linux-v5.15/drivers/gpu/drm/bridge/ |
| D | Kconfig | 311 tristate "TI TPD12S015 HDMI level shifter and ESD protection"
315 Texas Instruments TPD12S015 HDMI level shifter and ESD protection
|
