| /Linux-v5.15/drivers/leds/ |
| D | leds-lt3593.c | 26 int pulses; in lt3593_led_set() local
42 pulses = 32 - (value * 32) / 255; in lt3593_led_set()
44 if (pulses == 0) { in lt3593_led_set()
53 while (pulses--) { in lt3593_led_set()
|
| /Linux-v5.15/Documentation/devicetree/bindings/hwmon/ |
| D | pwm-fan.txt | 17 - pulses-per-revolution : define the number of pulses per fan revolution for
57 pulses-per-revolution = <2>;
66 pulses-per-revolution = <2>, <1>;
|
| /Linux-v5.15/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-timer-stm32 | 37 OC4REF rising or falling edges generate pulses.
39 OC6REF rising or falling edges generate pulses.
41 OC4REF or OC6REF rising edges generate pulses.
44 pulses.
46 OC5REF or OC6REF rising edges generate pulses.
49 pulses.
|
| /Linux-v5.15/drivers/hwmon/ |
| D | pwm-fan.c | 26 atomic_t pulses; member
67 atomic_inc(&tach->pulses); in pulse_handler()
81 int pulses; in sample_timer() local
83 pulses = atomic_read(&tach->pulses); in sample_timer()
84 atomic_sub(pulses, &tach->pulses); in sample_timer()
85 tach->rpm = (unsigned int)(pulses * 1000 * 60) / in sample_timer()
|
| /Linux-v5.15/Documentation/input/devices/ |
| D | walkera0701.rst | 20 pulses from processor to HF part can be found at pin 2 of this connector,
22 modulation pulses to PC, signal pulses must be amplified.
62 Signal pulses
98 (Warning, pulses on ACK are inverted by transistor, irq is raised up on sync
105 values can be sampled between sync pulses.
|
| /Linux-v5.15/drivers/net/wireless/ath/ |
| D | dfs_pri_detector.c | 162 struct list_head *l = &pde->pulses; in pulse_queue_get_tail()
215 list_add(&p->head, &pde->pulses); in pulse_queue_enqueue()
228 list_for_each_entry(p, &pde->pulses, head) { in pseq_handler_create_sequences()
257 list_for_each_entry_continue(p2, &pde->pulses, head) { in pseq_handler_create_sequences()
366 list_for_each_entry_safe(p, p0, &pde->pulses, head) { in pri_detector_reset()
429 INIT_LIST_HEAD(&de->pulses); in pri_detector_init()
|
| D | dfs_pri_detector.h | 70 struct list_head pulses; member
|
| /Linux-v5.15/Documentation/hwmon/ |
| D | g762.rst | 18 hardware characteristics of the system (reference clock, pulses per
36 number of pulses per fan revolution. Supported values
71 system: a reference clock source frequency, a number of pulses per fan
|
| D | sl28cpld.rst | 35 fan1_input Fan RPM. Assuming 2 pulses per revolution.
|
| D | g760a.rst | 23 consecutive speed pulses. The period is defined in terms of clock
|
| D | nsa320.rst | 55 is reduced from 100 us to less than 15 us then data pulses are likely to be
|
| D | dme1737.rst | 163 to the number of pulses per fan revolution that the connected tachometer
165 that generate 2 pulses per revolution. Fan inputs 5-6 also provide a max
296 number of pulses per revolution that
|
| D | smsc47b397.rst | 90 The SIO counts the number of 90kHz (11.111us) pulses per revolution.
|
| /Linux-v5.15/arch/arm/boot/dts/ |
| D | aspeed-bmc-opp-swift.dts | 349 tach-pulses = <2>;
361 tach-pulses = <2>;
373 tach-pulses = <2>;
385 tach-pulses = <2>;
397 tach-pulses = <2>;
|
| D | aspeed-bmc-opp-tacoma.dts | 489 tach-pulses = <2>;
502 tach-pulses = <2>;
515 tach-pulses = <2>;
528 tach-pulses = <2>;
|
| D | aspeed-bmc-ibm-rainier.dts | 1312 tach-pulses = <2>;
1318 tach-pulses = <2>;
1324 tach-pulses = <2>;
1330 tach-pulses = <2>;
1336 tach-pulses = <2>;
1342 tach-pulses = <2>;
|
| /Linux-v5.15/Documentation/userspace-api/media/rc/ |
| D | lirc-set-send-carrier.rst | 34 Set send carrier used to modulate IR PWM pulses and spaces.
|
| D | lirc-set-rec-carrier.rst | 34 Set receive carrier used to modulate IR PWM pulses and spaces.
|
| /Linux-v5.15/Documentation/devicetree/bindings/leds/ |
| D | leds-is31fl319x.txt | 38 by reducing the dury-cycle of pulses and not the current, which
|
| /Linux-v5.15/Documentation/i2c/ |
| D | gpio-fault-injection.rst | 81 register 0x00 (if it has registers) when further clock pulses happen on SCL.
82 This is why bus recovery (up to 9 clock pulses) must either check SDA or send
|
| /Linux-v5.15/Documentation/driver-api/ |
| D | reset.rst | 42 carefully timed sequence of pulses on multiple reset lines.
61 trigger reset pulses, or to query reset line status.
|
| /Linux-v5.15/drivers/gpu/drm/i915/ |
| D | Kconfig.profile | 42 int "Interval between heartbeat pulses (ms)"
|
| /Linux-v5.15/drivers/leds/trigger/ |
| D | Kconfig | 25 This allows LEDs to blink in one-shot pulses with parameters
|
| /Linux-v5.15/Documentation/devicetree/bindings/memory-controllers/ |
| D | omap-gpmc.txt | 87 - gpmc,cycle2cycle-delay-ns: Delay between chip-select pulses
|
| /Linux-v5.15/drivers/media/rc/ |
| D | Kconfig | 334 Note that this device can only record bursts of 36 IR pulses and
374 wave and pulses.
|
