Searched refs:operate (Results 1 – 25 of 181) sorted by relevance
12345678
| /Linux-v5.15/Documentation/mips/ |
| D | ingenic-tcu.rst | 29 operate.
35 - On the oldest SoCs (up to JZ4740), all of the eight channels operate in
37 - On JZ4725B, channel 5 operates as TCU2, the others operate as TCU1.
38 - On newest SoCs (JZ4750 and above), channels 1-2 operate as TCU2, the
39 others operate as TCU1.
|
| /Linux-v5.15/Documentation/devicetree/bindings/serial/ |
| D | nxp,sc16is7xx.txt | 25 should operate in IrDA mode.
61 should operate in IrDA mode.
|
| /Linux-v5.15/Documentation/devicetree/bindings/mtd/ |
| D | microchip,mchp23k256.txt | 8 - spi-max-frequency : Maximum frequency of the SPI bus the chip can operate at
|
| /Linux-v5.15/Documentation/sh/ |
| D | booting.rst | 9 inter-operate with old bootloaders must either use a builtin DTB or
|
| /Linux-v5.15/Documentation/devicetree/bindings/ipmi/ |
| D | aspeed,ast2400-ibt-bmc.txt | 17 interrupt, the driver will operate in poll mode.
|
| /Linux-v5.15/Documentation/scsi/ |
| D | bnx2fc.rst | 13 depend on the state of the network interfaces to operate. As such, the network
28 2. Configure the interfaces on which bnx2fc driver has to operate on.
|
| /Linux-v5.15/drivers/pci/endpoint/ |
| D | Kconfig | 14 controller that can operate in endpoint mode.
|
| /Linux-v5.15/drivers/usb/dwc2/ |
| D | Kconfig | 35 driver to operate in Host-only mode.
45 driver to operate in Peripheral-only mode. This option requires
|
| /Linux-v5.15/Documentation/devicetree/bindings/timer/ |
| D | ti,keystone-timer.txt | 6 timers, each half can operate in conjunction (chain mode) or independently
|
| D | ti,davinci-timer.txt | 6 timers, each half can operate in conjunction (chain mode) or independently
|
| /Linux-v5.15/Documentation/devicetree/bindings/net/can/ |
| D | tcan4x5x.txt | 12 operate at should be less than or equal to 18 MHz.
|
| /Linux-v5.15/Documentation/driver-api/ |
| D | mailbox.rst | 43 The client might want to operate in blocking mode (synchronously
106 dc_sync->cl.tx_done = NULL; /* operate in blocking mode */
|
| /Linux-v5.15/Documentation/devicetree/bindings/phy/ |
| D | nvidia,tegra20-usb-phy.txt | 60 operate in legacy mode (as APX 2500 / 2600). In legacy mode some
69 otg means it can operate as either ("on the go")
|
| /Linux-v5.15/fs/sysfs/ |
| D | Kconfig | 16 Some system agents rely on the information in sysfs to operate.
|
| /Linux-v5.15/tools/io_uring/ |
| D | README | 17 io_uring-bench should operate on. This uses the raw io_uring
|
| /Linux-v5.15/Documentation/devicetree/bindings/media/ |
| D | samsung-s5k6a3.txt | 23 configured to operate, in Hz; if this property is not
|
| D | samsung-s5k5baf.txt | 23 configured to operate, in Hz; if this property is not
|
| /Linux-v5.15/Documentation/devicetree/bindings/cpufreq/ |
| D | cpufreq-st.txt | 7 the DT and operate in the usual way.
|
| /Linux-v5.15/Documentation/i2c/busses/ |
| D | i2c-taos-evm.rst | 47 to operate at 1200 bps. However, I don't think this is a big concern in
|
| /Linux-v5.15/Documentation/devicetree/bindings/net/ |
| D | micrel.txt | 39 - micrel,fiber-mode: If present the PHY is configured to operate in fiber mode
|
| /Linux-v5.15/drivers/net/wireless/ath/wil6210/ |
| D | Kconfig | 24 ISR registers on wil6210 chip may operate in either
|
| /Linux-v5.15/Documentation/hwmon/ |
| D | ads7828.rst | 56 It can operate in single ended mode (8 +ve inputs) or in differential mode,
|
| /Linux-v5.15/Documentation/power/ |
| D | opp.rst | 70 As the system proceeds to operate, SoC framework may choose to make certain
77 operational functions operate only on available opps:
152 /* dont operate on the pointer.. just do a sanity check.. */
347 for the OPP library to operate on. Pointer to this structure is
|
| /Linux-v5.15/arch/m68k/ |
| D | Kconfig.bus | 54 operate ISA cards on Atari. Only 8 bit cards are supported, and
|
| /Linux-v5.15/Documentation/networking/ |
| D | x25.rst | 29 option appeared, XOT. This allows X.25 Packet Layer frames to operate over
|
12345678
