Searched refs:ohm (Results 1 – 24 of 24) sorted by relevance
| /Linux-v5.15/drivers/hwmon/ |
| D | ntc_thermistor.c | 26 unsigned int ohm; member
66 { .temp_c = -40, .ohm = 1747920 },
67 { .temp_c = -35, .ohm = 1245428 },
68 { .temp_c = -30, .ohm = 898485 },
69 { .temp_c = -25, .ohm = 655802 },
70 { .temp_c = -20, .ohm = 483954 },
71 { .temp_c = -15, .ohm = 360850 },
72 { .temp_c = -10, .ohm = 271697 },
73 { .temp_c = -5, .ohm = 206463 },
74 { .temp_c = 0, .ohm = 158214 },
[all …]
|
| /Linux-v5.15/arch/arm/boot/dts/ |
| D | cros-adc-thermistors.dtsi | 16 pullup-ohm = <47000>;
17 pulldown-ohm = <0>;
23 pullup-ohm = <47000>;
24 pulldown-ohm = <0>;
30 pullup-ohm = <47000>;
31 pulldown-ohm = <0>;
37 pullup-ohm = <47000>;
38 pulldown-ohm = <0>;
|
| D | ste-hrefv60plus.dtsi | 57 pullup-ohm = <220000>;
58 pulldown-ohm = <0>;
66 pullup-ohm = <220000>;
67 pulldown-ohm = <0>;
|
| D | exynos3250-monk.dts | 147 pullup-ohm = <100000>;
148 pulldown-ohm = <100000>;
155 pullup-ohm = <100000>;
156 pulldown-ohm = <100000>;
|
| D | exynos3250-rinato.dts | 147 pullup-ohm = <100000>;
148 pulldown-ohm = <100000>;
155 pullup-ohm = <100000>;
156 pulldown-ohm = <100000>;
|
| D | exynos4412-midas.dtsi | 307 pullup-ohm = <100000>; /* 100K */
308 pulldown-ohm = <100000>; /* 100K */
315 pullup-ohm = <100000>; /* 100K */
316 pulldown-ohm = <100000>; /* 100K */
|
| /Linux-v5.15/Documentation/devicetree/bindings/hwmon/ |
| D | ntc_thermistor.txt | 24 - "pullup-ohm" Pull up resistor value in ohms
25 - "pulldown-ohm" Pull down resistor value in ohms
41 pullup-ohm = <47000>;
42 pulldown-ohm = <0>;
|
| /Linux-v5.15/drivers/iio/potentiometer/ |
| D | max5432.c | 28 unsigned long ohm; member
52 if (unlikely(data->ohm > INT_MAX)) in max5432_read_raw()
55 *val = data->ohm; in max5432_read_raw()
103 data->ohm = (unsigned long)device_get_match_data(dev); in max5432_probe()
|
| /Linux-v5.15/Documentation/devicetree/bindings/phy/ |
| D | rockchip-emmc-phy.txt | 16 - drive-impedance-ohm: Specifies the drive impedance in Ohm.
40 drive-impedance-ohm = <50>;
|
| D | mxs-usb-phy.txt | 18 high-speed trimming resistor connected in parallel with the 45 ohm resistor
21 high-speed trimming resistor connected in parallel with the 45 ohm resistor
|
| /Linux-v5.15/arch/arm64/boot/dts/rockchip/ |
| D | rk3399-gru-kevin.dts | 70 pullup-ohm = <25500>;
71 pulldown-ohm = <0>;
79 pullup-ohm = <25500>;
80 pulldown-ohm = <0>;
|
| D | rk3399-puma.dtsi | 102 drive-impedance-ohm = <33>;
|
| D | rk3399.dtsi | 1490 drive-impedance-ohm = <50>;
|
| /Linux-v5.15/arch/arm64/boot/dts/ti/ |
| D | k3-am6548-iot2050-advanced.dts | 54 ti,driver-strength-ohm = <50>;
|
| D | k3-j7200-common-proc-board.dts | 277 ti,driver-strength-ohm = <50>;
287 ti,driver-strength-ohm = <50>;
|
| D | k3-am654-base-board.dts | 352 ti,driver-strength-ohm = <50>;
365 ti,driver-strength-ohm = <50>;
|
| D | k3-am642-evm.dts | 413 ti,driver-strength-ohm = <50>;
423 ti,driver-strength-ohm = <50>;
|
| D | k3-j721e-common-proc-board.dts | 324 ti,driver-strength-ohm = <50>;
334 ti,driver-strength-ohm = <50>;
|
| D | k3-am642-sk.dts | 302 ti,driver-strength-ohm = <50>;
|
| D | k3-am65-iot2050-common.dtsi | 556 ti,driver-strength-ohm = <50>;
|
| /Linux-v5.15/arch/arm64/boot/dts/mediatek/ |
| D | mt8183-pumpkin.dts | 61 pullup-ohm = <390000>;
62 pulldown-ohm = <0>;
|
| /Linux-v5.15/arch/arm64/boot/dts/exynos/ |
| D | exynos5433-tm2-common.dtsi | 144 pullup-ohm = <100000>;
145 pulldown-ohm = <0>;
152 pullup-ohm = <100000>;
153 pulldown-ohm = <0>;
161 pullup-ohm = <100000>;
162 pulldown-ohm = <0>;
|
| /Linux-v5.15/Documentation/admin-guide/auxdisplay/ |
| D | cfag12864b.rst | 75 Ground (21)---[GND] [GND]---[P1]---(18) Vee - R = Resistor = 22 ohm
|
| /Linux-v5.15/Documentation/ABI/testing/ |
| D | sysfs-bus-iio | 1743 into an ohm value.
|
