Home
last modified time | relevance | path

Searched refs:lilo (Results 1 – 25 of 32) sorted by relevance

12

/Linux-v5.15/arch/x86/boot/
Dinstall.sh52 if [ -x /sbin/lilo ]; then
53 /sbin/lilo
54 elif [ -x /etc/lilo/install ]; then
55 /etc/lilo/install
/Linux-v5.15/Documentation/translations/zh_CN/admin-guide/
DREADME.rst231 - 执行 ``make`` 来创建压缩内核映像。如果您安装了lilo以适配内核makefile，
232 那么也可以进行 ``makeinstall`` ，但是您可能需要先检查特定的lilo设置。
263 如果从硬盘引导Linux，很可能使用LILO，它使用/etc/lilo.conf文件中
269 重新安装LILO通常需要运行/sbin/LILO。您可能希望编辑/etc/lilo.conf
/Linux-v5.15/Documentation/translations/zh_TW/admin-guide/
DREADME.rst234 - 執行 ``make`` 來創建壓縮內核映像。如果您安裝了lilo以適配內核makefile，
235 那麼也可以進行 ``makeinstall`` ，但是您可能需要先檢查特定的lilo設置。
266 如果從硬碟引導Linux，很可能使用LILO，它使用/etc/lilo.conf文件中
272 重新安裝LILO通常需要運行/sbin/LILO。您可能希望編輯/etc/lilo.conf
/Linux-v5.15/Documentation/fb/
Dsisfb.rst38 Well, it depends: If compiled statically into the kernel, use lilo's append
39 statement to add the parameters to the kernel command line. Please see lilo's
44 lilo.conf::
107 in lilo's or grub's configuration file; mode selection is done using the
Dintelfb.rst97 In /etc/lilo.conf, add the line::
Dvesafb.rst70 lilo.conf file and rerun LILO. Then you can type in the desired
Dintel810.rst189 In /etc/lilo.conf, add the line::
/Linux-v5.15/Documentation/admin-guide/blockdev/
Dfloppy.rst16 lilo. This option can be typed at the boot prompt, or entered in the
17 lilo configuration file.
20 at the lilo boot prompt (if you have a thinkpad)::
24 You may also enter the following line in /etc/lilo.conf, in the description
34 If you give options both in the lilo config file and on the boot
/Linux-v5.15/Documentation/admin-guide/
Dserial-console.rst72 In lilo.conf (global section)::
77 again in lilo.conf (kernel section)::
DREADME.rst268 possible to do ``make install`` if you have lilo installed to suit the
269 kernel makefiles, but you may want to check your particular lilo setup first.
310 uses the kernel image as specified in the file /etc/lilo.conf. The
317 Reinstalling LILO is usually a matter of running /sbin/lilo.
318 You may wish to edit /etc/lilo.conf to specify an entry for your
Dldm.rst102 If you enable LDM support, then lilo is capable of booting from any of the
Dinitrd.rst59 have to specify the RAM disk image file in /etc/lilo.conf, using the
196 or to the section of the respective kernel in ``/etc/lilo.conf``, and pass
203 and run ``/sbin/lilo``
/Linux-v5.15/Documentation/networking/device_drivers/appletalk/
Dcops.rst46 Or in lilo.conf put something like this::
Dltpc.rst24 as the following to your /etc/lilo.conf::
/Linux-v5.15/Documentation/cdrom/
Dide-cd.rst184 lilo option. See Documentation/ide/ide.rst. (This feature was
188 driver to assume that one exists by using a lilo option of the
251 adding `append="hdX=noprobe hdX=cdrom"` to your lilo.conf file and running
252 lilo (again where X is the drive letter corresponding to where your drive
/Linux-v5.15/Documentation/x86/i386/
DIO-APIC.rst45 is non-trivial though and cannot be automated. One sample /etc/lilo.conf
/Linux-v5.15/Documentation/power/
Dswsusp-dmcrypt.rst44 modify. For lilo the simplest setup looks like the following
/Linux-v5.15/Documentation/scsi/
Dscsi-changer.rst101 (append="max_scsi_luns=1" in lilo.conf should do the trick)
Dadvansys.rst177 recognize the 'advansys' LILO command line and /etc/lilo.conf option.
DBusLogic.rst537 LILO Linux Boot Loader (in /etc/lilo.conf)::
570 Then install "arch/x86/boot/zImage" as your standard kernel, run lilo if
Dsym53c8xx_2.rst498 Example of boot setup command under lilo prompt::
500 lilo: linux root=/dev/sda2 sym53c8xx.cmd_per_lun=4 sym53c8xx.sync=10 sym53c8xx.debug=0x200
/Linux-v5.15/drivers/tty/serial/
DKconfig45 your boot loader (lilo or loadlin) about how to pass options to the
73 your boot loader (lilo or loadlin) about how to pass options to the
409 your boot loader (lilo or loadlin) about how to pass options to the
442 your boot loader (lilo or loadlin) about how to pass options to the
471 your boot loader (lilo or loadlin) about how to pass options to the
803 your boot loader (lilo or loadlin) about how to pass options to the
/Linux-v5.15/drivers/tty/
DKconfig69 bootparam" or see the documentation of your boot loader (lilo or
/Linux-v5.15/drivers/char/
DKconfig52 or see the documentation of your boot loader (lilo or loadlin) about
/Linux-v5.15/drivers/tty/serial/8250/
DKconfig101 your boot loader (grub or lilo or loadlin) about how to pass options

12