Searched refs:fiber (Results 1 – 20 of 20) sorted by relevance
| /Linux-v5.15/Documentation/devicetree/bindings/net/ |
| D | micrel.txt | 39 - micrel,fiber-mode: If present the PHY is configured to operate in fiber mode
41 Some PHYs, such as the KSZ8041FTL variant, support fiber mode, enabled
43 registers whether the PHY is in fiber mode, so this boolean device tree
46 In fiber mode, auto-negotiation is disabled and the PHY can only work in
|
| D | keystone-netcp.txt | 101 - mac<->fiber mode: 3
|
| /Linux-v5.15/drivers/net/fddi/ |
| D | Kconfig | 12 run over copper or fiber. If you are connected to such a network and
23 This is support for the DEC FDDIcontroller 700 (DEFZA-AA, fiber)
|
| /Linux-v5.15/drivers/net/ethernet/alacritech/ |
| D | Kconfig | 24 both copper and fiber.
|
| /Linux-v5.15/drivers/net/hippi/ |
| D | Kconfig | 12 can run over copper (25m) or fiber (300m on multi-mode or 10km on
|
| /Linux-v5.15/drivers/net/phy/ |
| D | marvell.c | 1520 int fiber, int status) in marvell_read_status_page_an() argument
1549 if (!fiber) { in marvell_read_status_page_an()
1591 int fiber; in marvell_read_status_page() local
1610 fiber = 1; in marvell_read_status_page()
1612 fiber = 0; in marvell_read_status_page()
1619 phydev->port = fiber ? PORT_FIBRE : PORT_TP; in marvell_read_status_page()
1622 err = marvell_read_status_page_an(phydev, fiber, status); in marvell_read_status_page()
|
| D | Kconfig | 335 fiber connections.
|
| /Linux-v5.15/arch/arm64/boot/dts/hisilicon/ |
| D | hip06.dtsi | 535 media-type = "fiber";
543 media-type = "fiber";
|
| D | hip07.dtsi | 1420 media-type = "fiber";
1430 media-type = "fiber";
|
| /Linux-v5.15/drivers/net/dsa/microchip/ |
| D | ksz_common.h | 36 u32 fiber:1; /* port is fiber */ member
|
| D | ksz8795.c | 885 if (dev->ports[p].fiber) in ksz8_w_phy()
1424 p->fiber = 1; in ksz8_config_cpu_port()
1426 if (p->fiber) in ksz8_config_cpu_port()
|
| /Linux-v5.15/Documentation/networking/device_drivers/ethernet/intel/ |
| D | e1000e.rst | 327 between copper-based adapters and fiber-based adapters.
349 An Intel(R) Ethernet Network Adapter using fiber-based connections, however,
|
| D | ixgb.rst | 59 | 82597EX | Intel(R) PRO/10GbE LR/SR/CX4 | - 10G Base-LR (fiber) |
60 | | Server Adapters | - 10G Base-SR (fiber) |
|
| D | e1000.rst | 341 If the board uses a fiber interface, these keywords are ignored, and the
342 fiber interface board only links at 1000 Mbps full-duplex.
|
| D | i40e.rst | 370 between copper-based adapters and fiber-based adapters.
395 An Intel(R) Ethernet Network Adapter using fiber-based connections, however,
|
| D | ixgbe.rst | 100 "ifconfig ethX down" turns off the laser for 82599-based SFP+ fiber adapters.
|
| D | ice.rst | 680 between copper-based adapters and fiber-based adapters.
|
| /Linux-v5.15/Documentation/networking/device_drivers/ethernet/dlink/ |
| D | dl2k.rst | 232 available for fiber adapter.
|
| /Linux-v5.15/drivers/staging/most/Documentation/ |
| D | driver_usage.txt | 11 fiber optics, unshielded twisted pair cables (UTP) and coax cables. MOST
|
| /Linux-v5.15/Documentation/networking/device_drivers/ethernet/cirrus/ |
| D | cs89x0.rst | 71 or fiber networks).
|
