| /Linux-v5.15/Documentation/devicetree/bindings/regulator/ |
| D | tps65132-regulator.txt | 17 -active-discharge-gpios: (active high, output) Some configurations use delay mechanisms
19 the enable signal goes low. This GPIO is used to actively discharge
20 the delay mechanism. Requires specification of ti,active-discharge-time-us
21 -ti,active-discharge-time-us: how long the active discharge gpio should be
22 asserted for during active discharge, in microseconds.
43 regulator-active-discharge = <0>;
|
| D | tps62360-regulator.txt | 12 - ti,enable-vout-discharge: Enable output discharge. This is boolean value.
43 ti,enable-vout-discharge;
|
| D | max8973-regulator.txt | 24 -maxim,enable-active-discharge: boolean: enable active discharge.
|
| /Linux-v5.15/Documentation/devicetree/bindings/display/ |
| D | repaper.txt | 10 - discharge-gpios: Discharge control
47 discharge-gpios = <&gpio 15 0>;
|
| /Linux-v5.15/include/sound/ |
| D | wm2200.h | 39 unsigned int discharge:1; /** Actively discharge */ member
|
| D | da7218.h | 80 bool discharge; member
|
| /Linux-v5.15/drivers/gpu/drm/tiny/ |
| D | repaper.c | 72 struct gpio_desc *discharge; member
636 gpiod_set_value_cansleep(epd->discharge, 1); in power_off()
638 gpiod_set_value_cansleep(epd->discharge, 0); in power_off()
659 gpiod_set_value_cansleep(epd->discharge, 0); in repaper_pipe_enable()
1010 epd->discharge = devm_gpiod_get(dev, "discharge", GPIOD_OUT_LOW); in repaper_probe()
1011 if (IS_ERR(epd->discharge)) { in repaper_probe()
1012 ret = PTR_ERR(epd->discharge); in repaper_probe()
|
| /Linux-v5.15/arch/arm/boot/dts/ |
| D | stm32mp15xx-dhcor-som.dtsi | 152 regulator-active-discharge = <1>;
158 regulator-active-discharge = <1>;
|
| D | stm32mp15xx-osd32.dtsi | 182 regulator-active-discharge = <1>;
188 regulator-active-discharge = <1>;
|
| D | stm32mp157a-stinger96.dtsi | 219 regulator-active-discharge = <1>;
225 regulator-active-discharge = <1>;
|
| D | tegra30-asus-nexus7-grouper-ti-pmic.dtsi | 138 ti,enable-vout-discharge;
|
| D | stm32mp157c-odyssey-som.dtsi | 213 regulator-active-discharge = <1>;
|
| D | stm32mp157c-ed1.dts | 285 regulator-active-discharge = <1>;
|
| D | stm32mp15xx-dhcom-som.dtsi | 375 regulator-active-discharge = <1>;
|
| D | ste-ux500-samsung-golden.dts | 340 /* ESD (electrostatic discharge) detection interrupt */
|
| D | stm32mp15xx-dkx.dtsi | 398 regulator-active-discharge = <1>;
|
| /Linux-v5.15/Documentation/devicetree/bindings/sound/ |
| D | da7218.txt | 64 - dlg,discharge : Boolean flag, auto discharge of Mic Bias on jack removal
|
| /Linux-v5.15/arch/arm/mach-pxa/ |
| D | sharpsl_pm.h | 18 void (*discharge)(int); member
|
| D | corgi_pm.c | 164 .discharge = corgi_discharge,
|
| D | spitz_pm.c | 199 .discharge = spitz_discharge,
|
| D | sharpsl_pm.c | 526 sharpsl_pm.machinfo->discharge(1); in sharpsl_check_battery_voltage()
541 sharpsl_pm.machinfo->discharge(0); in sharpsl_check_battery_voltage()
|
| /Linux-v5.15/include/linux/mfd/arizona/ |
| D | pdata.h | 61 unsigned int discharge:1; /** Actively discharge */ member
|
| /Linux-v5.15/arch/arm64/boot/dts/qcom/ |
| D | msm8916-huawei-g7.dts | 151 regulator-active-discharge = <1>;
159 regulator-active-discharge = <1>;
|
| D | sdm845-xiaomi-beryllium.dts | 272 qcom,discharge-resistor-kohms = <300>;
|
| /Linux-v5.15/Documentation/ABI/testing/ |
| D | sysfs-platform-dptf | 96 (RO) The battery discharge current capability obtained from battery fuel gauge in
|
