| /Linux-v5.15/Documentation/hwmon/ |
| D | amc6821.rst | 70 0 degree C to 124 degree C in steps of
71 4 degree C. Read it out after writing to get
80 temp2_auto_point1_temp rw Must be between 0 degree C and 63 degree C and
87 0 degree C to 124 degree C in steps
88 of 4 degree C.
|
| D | nct7904.rst | 38 temp1_input Local temperature (1/1000 degree,
39 0.125 degree resolution)
41 temp[2-9]_input CPU temperatures (1/1000 degree,
42 0.125 degree resolution)
|
| D | tmp102.rst | 23 sensor is accurate to 0.5 degree over the range of -25 to +85 C, and to 1.0
24 degree from -40 to +125 C. Resolution of the sensor is 0.0625 degree. The
|
| D | ds1621.rst | 67 degree Celsius to +125 in 0.5 increments. You may convert this into a
83 1.0 degree Celsius to avoid Tout "bouncing", though!
125 - DS1621: +/- 0.5 degree Celsius (from 0 to +70 degrees)
126 - DS1625: +/- 0.5 degree Celsius (from 0 to +70 degrees)
127 - DS1631: +/- 0.5 degree Celsius (from 0 to +70 degrees)
128 - DS1721: +/- 1.0 degree Celsius (from -10 to +85 degrees)
129 - DS1731: +/- 1.0 degree Celsius (from -10 to +85 degrees)
|
| D | sht21.rst | 40 0.2 degree Celsius) compared with the SHT21 (2.0% relative humidity,
41 0.3 degree Celsius).
63 humidity and 66 ms for temperature. To keep self heating below 0.1 degree
|
| D | xgene-hwmon.rst | 19 - SoC on-die temperature in milli-degree C
30 - SoC on-die temperature (milli-degree C)
|
| D | tmp401.rst | 65 Celsius. Resolution of the remote sensor is 0.0625 degree. Local
66 sensor resolution can be set to 0.5, 0.25, 0.125 or 0.0625 degree (not
68 degree).
|
| D | adm1031.rst | 37 degree for the local temperature, 0.125 degree for the remote temperatures.
|
| D | ds620.rst | 24 into non-volatile on-chip registers). Temperature range is -55 degree Celsius
25 to +125. Between 0 and 70 degree Celsius, accuracy is 0.5 Kelvin. The value
|
| D | tmp108.rst | 27 degree from -40 to +125 C. Resolution of the sensor is 0.0625 degree. The
|
| D | tc74.rst | 17 The tc74 has an 8-bit sensor, with 1 degree centigrade resolution
|
| D | tmp513.rst | 35 -40 to + 125 degrees with a resolution of 0.0625 degree C.
40 0 to 127.5 degrees with a resolution of 0.5 degree.
|
| D | max6642.rst | 27 is 0.25 degree for the local temperature and for the remote temperature.
|
| D | max1619.rst | 27 is 1.0 degree for the local temperature and for the remote temperature.
|
| D | sht4x.rst | 25 and temperature sensor. Temperature is measured in degree celsius, relative
|
| D | lm63.rst | 64 degree for the local temperature, 0.125 degree for the remote temperature.
|
| D | twl4030-madc-hwmon.rst | 48 degree Celsius. The Battery charging current channel represents
|
| D | w83773g.rst | 30 Resolution for both the local and remote channels is 0.125 degree C.
|
| /Linux-v5.15/Documentation/driver-api/thermal/ |
| D | exynos_thermal.rst | 40 Trimming info for 25 degree Celsius (stored at TRIMINFO register)
41 Temperature code measured at 25 degree Celsius which is unchanged
43 Trimming info for 85 degree Celsius (stored at TRIMINFO register)
44 Temperature code measured at 85 degree Celsius which is unchanged
|
| /Linux-v5.15/drivers/mtd/nand/raw/atmel/ |
| D | pmecc.c | 223 unsigned int poly, degree, table_size; in atmel_pmecc_create_gf_tables() local
227 degree = PMECC_GF_DIMENSION_13; in atmel_pmecc_create_gf_tables()
231 degree = PMECC_GF_DIMENSION_14; in atmel_pmecc_create_gf_tables()
245 ret = atmel_pmecc_build_gf_tables(degree, poly, gf_tables); in atmel_pmecc_create_gf_tables()
448 int degree = get_sectorsize(user) == 512 ? 13 : 14; in atmel_pmecc_substitute() local
449 int cw_len = BIT(degree) - 1; in atmel_pmecc_substitute()
468 for (j = 0; j < degree; j++) { in atmel_pmecc_substitute()
494 int degree = get_sectorsize(user) == 512 ? 13 : 14; in atmel_pmecc_get_sigma() local
495 int cw_len = BIT(degree) - 1; in atmel_pmecc_get_sigma()
644 int degree = sector_size == 512 ? 13 : 14; in atmel_pmecc_err_location() local
[all …]
|
| /Linux-v5.15/Documentation/devicetree/bindings/spi/ |
| D | spi-samsung.txt | 66 - 1: 90 degree phase shift sampling.
67 - 2: 180 degree phase shift sampling.
68 - 3: 270 degree phase shift sampling.
|
| /Linux-v5.15/Documentation/devicetree/bindings/sound/ |
| D | rt1011.txt | 26 u32. The temperature was measured while doing the calibration. Units: Celsius degree
|
| /Linux-v5.15/mm/ |
| D | rmap.c | 93 anon_vma->degree = 1; /* Reference for first vma */ in anon_vma_alloc()
211 anon_vma->degree++; in __anon_vma_prepare()
304 anon_vma != src->anon_vma && anon_vma->degree < 2) in anon_vma_clone()
308 dst->anon_vma->degree++; in anon_vma_clone()
378 anon_vma->parent->degree++; in anon_vma_fork()
410 anon_vma->parent->degree--; in unlink_anon_vmas()
418 vma->anon_vma->degree--; in unlink_anon_vmas()
436 VM_WARN_ON(anon_vma->degree); in unlink_anon_vmas()
|
| /Linux-v5.15/drivers/media/pci/intel/ipu3/ |
| D | cio2-bridge.h | 71 u8 degree; member
|
| /Linux-v5.15/drivers/net/phy/ |
| D | nxp-c45-tja11xx.c | 892 u64 degree; in nxp_c45_set_delays() local
896 degree = div_u64(tx_delay, PS_PER_DEGREE); in nxp_c45_set_delays()
898 ID_ENABLE | nxp_c45_get_phase_shift(degree)); in nxp_c45_set_delays()
906 degree = div_u64(rx_delay, PS_PER_DEGREE); in nxp_c45_set_delays()
908 ID_ENABLE | nxp_c45_get_phase_shift(degree)); in nxp_c45_set_delays()
|
