Searched refs:cpol (Results 1 – 25 of 88) sorted by relevance
1234
| /Linux-v5.15/drivers/spi/ |
| D | spi-bitbang-txrx.h | 48 unsigned nsecs, unsigned cpol, unsigned flags, in bitbang_txrx_be_cpha0() argument
66 setsck(spi, !cpol); in bitbang_txrx_be_cpha0()
73 setsck(spi, cpol); in bitbang_txrx_be_cpha0()
80 unsigned nsecs, unsigned cpol, unsigned flags, in bitbang_txrx_be_cpha1() argument
90 setsck(spi, !cpol); in bitbang_txrx_be_cpha1()
99 setsck(spi, cpol); in bitbang_txrx_be_cpha1()
|
| D | spi-cavium.c | 38 bool cpha, cpol; in octeon_spi_do_transfer() local
46 cpol = mode & SPI_CPOL; in octeon_spi_do_transfer()
56 mpi_cfg.s.idlelo = cpha != cpol; in octeon_spi_do_transfer()
|
| D | spi-lp8841-rtc.c | 68 unsigned usecs, unsigned cpol, unsigned flags, in bitbang_txrx_be_cpha0_lsb() argument
88 setsck(data, !cpol); in bitbang_txrx_be_cpha0_lsb()
91 setsck(data, cpol); in bitbang_txrx_be_cpha0_lsb()
|
| D | spi-slave-mt27xx.c | 134 bool cpha, cpol; in mtk_spi_slave_prepare_message() local
138 cpol = spi->mode & SPI_CPOL ? 1 : 0; in mtk_spi_slave_prepare_message()
145 if (cpol) in mtk_spi_slave_prepare_message()
|
| /Linux-v5.15/arch/arm64/boot/dts/freescale/ |
| D | fsl-ls1028a-qds.dts | 129 spi-cpol;
139 spi-cpol;
149 spi-cpol;
164 spi-cpol;
174 spi-cpol;
184 spi-cpol;
199 spi-cpol;
|
| D | fsl-ls1012a-qds.dts | 81 spi-cpol;
91 spi-cpol;
|
| D | fsl-ls1088a-qds.dts | 36 spi-cpol;
46 spi-cpol;
|
| D | fsl-ls1046a-qds.dts | 51 spi-cpol;
61 spi-cpol;
|
| /Linux-v5.15/Documentation/devicetree/bindings/mtd/ |
| D | nxp-spifi.txt | 25 - spi-cpol : Controller only supports mode 0 and 3 so either
26 both spi-cpol and spi-cpha should be present or
46 spi-cpol;
|
| /Linux-v5.15/Documentation/devicetree/bindings/net/ieee802154/ |
| D | ca8210.txt | 8 - spi-cpol: Requires inverted clock polarity
22 spi-cpol;
|
| /Linux-v5.15/Documentation/devicetree/bindings/rtc/ |
| D | epson,rx6110.txt | 29 - spi-cpol: RX6110 works with SPI inverse clock polarity
38 spi-cpol;
|
| /Linux-v5.15/Documentation/devicetree/bindings/bus/ |
| D | moxtet.txt | 7 - spi-cpol : Required inverted clock polarity
33 spi-cpol;
|
| /Linux-v5.15/Documentation/devicetree/bindings/spi/ |
| D | qcom,spi-qup.txt | 71 spi-cpol;
89 spi-cpol;
99 spi-cpol;
|
| D | spi-octeon.txt | 26 spi-cpol;
|
| /Linux-v5.15/arch/arm64/boot/dts/broadcom/northstar2/ |
| D | ns2-svk.dts | 115 spi-cpol = <1>;
139 spi-cpol = <1>;
213 spi-cpol;
|
| /Linux-v5.15/Documentation/devicetree/bindings/net/ |
| D | qca,qca7000.txt | 19 - spi-cpol : Must be set
52 spi-cpol; /* SPI mode: CPOL=1 */
|
| /Linux-v5.15/arch/mips/boot/dts/brcm/ |
| D | bcm97358svmb.dts | 85 spi-cpol;
|
| D | bcm97360svmb.dts | 88 spi-cpol;
|
| D | bcm97425svmb.dts | 123 spi-cpol;
|
| /Linux-v5.15/arch/arm/boot/dts/ |
| D | bcm53340-ubnt-unifi-switch8.dts | 43 spi-cpol;
|
| D | r8a7744-iwg20m.dtsi | 77 spi-cpol;
|
| D | r8a7743-iwg20m.dtsi | 82 spi-cpol;
|
| D | r8a7745-iwg22m.dtsi | 86 spi-cpol;
|
| /Linux-v5.15/Documentation/devicetree/bindings/gpio/ |
| D | gpio-pisosr.txt | 33 spi-cpol;
|
| /Linux-v5.15/Documentation/devicetree/bindings/net/wireless/ |
| D | ti,wl1251.txt | 29 spi-cpol;
|
1234
