| /Linux-v5.15/arch/arm64/boot/dts/freescale/ |
| D | imx8mn-evk.dts | 18 cpu-supply = <&buck2>;
22 cpu-supply = <&buck2>;
26 cpu-supply = <&buck2>;
30 cpu-supply = <&buck2>;
52 buck2: BUCK2 { label
|
| D | imx8mp-phycore-som.dtsi | 26 cpu-supply = <&buck2>;
30 cpu-supply = <&buck2>;
34 cpu-supply = <&buck2>;
38 cpu-supply = <&buck2>;
109 buck2: BUCK2 { label
|
| D | imx8mq-phanbell.dts | 52 cpu-supply = <&buck2>;
56 cpu-supply = <&buck2>;
60 cpu-supply = <&buck2>;
64 cpu-supply = <&buck2>;
144 buck2: BUCK2 { label
145 regulator-name = "buck2";
|
| D | imx8mn-venice-gw7902.dts | 171 cpu-supply = <&buck2>;
175 cpu-supply = <&buck2>;
179 cpu-supply = <&buck2>;
183 cpu-supply = <&buck2>;
393 buck2: BUCK2 { label
394 regulator-name = "buck2";
|
| D | imx8mm-venice-gw7902.dts | 172 cpu-supply = <&buck2>;
176 cpu-supply = <&buck2>;
180 cpu-supply = <&buck2>;
184 cpu-supply = <&buck2>;
394 buck2: BUCK2 { label
395 regulator-name = "buck2";
|
| D | imx8mq-pico-pi.dts | 89 buck2: BUCK2 { label
90 regulator-name = "buck2";
|
| D | imx8mn-ddr4-evk.dts | 73 regulator-name = "buck2";
|
| /Linux-v5.15/Documentation/devicetree/bindings/mfd/ |
| D | max8998.txt | 29 - max8998,pmic-buck2-dvs-gpio: GPIO specifier for host gpio used
36 - max8998,pmic-buck2-default-dvs-idx: Default voltage setting selected from
47 Additional properties required if max8998,pmic-buck2-dvs-gpio is defined:
48 - max8998,pmic-buck2-dvs-voltage: An array of 2 voltage values in microvolts
49 for buck2 regulator that can be selected using dvs gpio.
98 max8998,pmic-buck2-default-dvs-idx = <0>;
99 max8998,pmic-buck2-dvs-gpio = <&gpx0 0 3 0 0>; /* SET3 */
100 max8998,pmic-buck2-dvs-voltage = <1350000>, <1300000>;
|
| D | da9052-i2c.txt | 20 buck2 : regulator BUCK PRO
51 buck2 {
|
| D | da9055.txt | 34 buck2 : regulator BUCK2
61 buck2: BUCK2 {
|
| D | rohm,bd70528-pmic.txt | 59 buck2: BUCK2 {
60 regulator-name = "buck2";
|
| D | da9062.txt | 57 buck2 : BUCK_2
68 buck2 : BUCK_2
|
| /Linux-v5.15/Documentation/devicetree/bindings/regulator/ |
| D | rohm,bd70528-regulator.txt | 4 - regulator-name: should be "buck1", "buck2", "buck3", "ldo1", "ldo2", "ldo3",
26 buck2: BUCK2 {
27 regulator-name = "buck2";
|
| D | samsung,s5m8767.txt | 16 - s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
17 units for buck2 when changing voltage using gpio dvs. Refer to [1] below
41 - s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs.
85 s5m8767,pmic-buck2-uses-gpio-dvs;
99 s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>,
|
| D | max8997-regulator.txt | 17 - max8997,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
18 units for buck2 when changing voltage using gpio dvs. Refer to [1] below
40 - max8997,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs.
98 max8997,pmic-buck2-uses-gpio-dvs;
113 max8997,pmic-buck2-dvs-voltage = <1100000>, <1100000>,
|
| D | 88pg86x.txt | 7 Optional subnodes for regulators: "buck1", "buck2", using common regulator
|
| D | 88pm800.txt | 14 buck1, buck2, buck3, buck4, buck5, ldo1, ldo2, ldo3, ldo4, ldo5, ldo6, ldo7,
|
| D | pv88090.txt | 35 regulator-name = "buck2";
|
| D | pv88080.txt | 40 regulator-name = "buck2";
|
| /Linux-v5.15/arch/arm/boot/dts/ |
| D | s5pv210-aquila.dts | 84 max8998,pmic-buck2-default-dvs-idx = <0>;
85 max8998,pmic-buck2-dvs-gpio = <&gph0 5 GPIO_ACTIVE_HIGH>;
86 max8998,pmic-buck2-dvs-voltage = <1200000>, <1200000>;
|
| D | s5pv210-goni.dts | 95 max8998,pmic-buck2-default-dvs-idx = <0>;
96 max8998,pmic-buck2-dvs-gpio = <&gph0 5 GPIO_ACTIVE_HIGH>;
97 max8998,pmic-buck2-dvs-voltage = <1200000>, <1200000>;
|
| D | imx53-qsb.dts | 28 buck2_reg: buck2 {
|
| D | berlin2cd-valve-steamlink.dts | 42 * less depending on leakage value in OTP), and buck2 likely used for
|
| D | stm32mp157c-ed1.dts | 174 buck2-supply = <&vin>;
197 vdd_ddr: buck2 {
|
| /Linux-v5.15/drivers/regulator/ |
| D | da9052-regulator.c | 332 DA9052_DCDC(BUCK2, buck2, 25, 500, 2075, 6, 6, DA9052_SUPPLY_VBPROGO),
349 DA9052_DCDC(BUCK2, buck2, 25, 500, 2075, 6, 6, DA9052_SUPPLY_VBPROGO),
|
