Searched refs:bit3 (Results 1 – 12 of 12) sorted by relevance
| /Linux-v5.15/Documentation/driver-api/mtd/ |
| D | nand_ecc.rst | 45 byte 0: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 rp0 rp2 rp4 ... rp14
46 byte 1: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 rp1 rp2 rp4 ... rp14
47 byte 2: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 rp0 rp3 rp4 ... rp14
48 byte 3: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 rp1 rp3 rp4 ... rp14
49 byte 4: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 rp0 rp2 rp5 ... rp14
51 byte 254: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 rp0 rp3 rp5 ... rp15
52 byte 255: bit7 bit6 bit5 bit4 bit3 bit2 bit1 bit0 rp1 rp3 rp5 ... rp15
67 Similarly cp1 is the sum of all bit1, bit3, bit5 and bit7.
70 - cp3 is the parity over bit2, bit3, bit6 and bit7.
71 - cp4 is the parity over bit0, bit1, bit2 and bit3.
[all …]
|
| /Linux-v5.15/include/uapi/linux/ |
| D | ioam6.h | 59 bit3:1, member
100 bit3:1, member
|
| /Linux-v5.15/Documentation/leds/ |
| D | leds-mlxcpld.rst | 53 [bit3,bit2,bit1,bit0] or
98 [bit3,bit2,bit1,bit0] or
110 [bit3,bit2,bit1,bit0]:
|
| /Linux-v5.15/drivers/pinctrl/bcm/ |
| D | pinctrl-bcm6358.c | 58 #define BCM6358_GPIO_PIN(a, b, bit1, bit2, bit3) \ argument
64 BCM6358_MODE_MUX_##bit3), \
|
| /Linux-v5.15/drivers/net/ethernet/hisilicon/hns3/hns3pf/ |
| D | hclge_debugfs.h | 57 bit3 : 1, member
|
| D | hclge_debugfs.c | 416 req.bit3); in hclge_dbg_dump_dcb_qset()
|
| /Linux-v5.15/Documentation/input/devices/ |
| D | sentelic.rst | 741 0x8204 bit3~bit0 0x01 RW revision ID
744 bit3 1 RO 0: rotate 180 degree
818 bit3 0 RW abs. coordinate only mode enable
849 bit3 0 RW on-pad fix vertical scrolling enable
870 bit3 0 RW finger up one packet output
|
| /Linux-v5.15/arch/arm/boot/dts/ |
| D | armada-370-synology-ds213j.dts | 232 syno_id_bit3_pin: syno-id-bit3-pin {
|
| /Linux-v5.15/Documentation/devicetree/bindings/pinctrl/ |
| D | pinctrl-mcp23s08.txt | 37 you have a chip with address 3 connected, you have to set bit3 to 1,
|
| /Linux-v5.15/tools/testing/selftests/net/ |
| D | ioam6_parser.c | 228 if (ioam6h->type.bit3) in check_ioam6_data()
|
| /Linux-v5.15/net/ipv6/ |
| D | ioam6.c | 691 if (trace->type.bit3) { in __ioam6_fill_trace_data()
|
| /Linux-v5.15/Documentation/userspace-api/ioctl/ |
| D | ioctl-number.rst | 218 'b' 00-FF conflict! bit3 vme host bridge
|
