1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3 * Driver for Motorola/Freescale IMX serial ports
4 *
5 * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
6 *
7 * Author: Sascha Hauer <sascha@saschahauer.de>
8 * Copyright (C) 2004 Pengutronix
9 */
10
11 #include <linux/module.h>
12 #include <linux/ioport.h>
13 #include <linux/init.h>
14 #include <linux/console.h>
15 #include <linux/sysrq.h>
16 #include <linux/platform_device.h>
17 #include <linux/tty.h>
18 #include <linux/tty_flip.h>
19 #include <linux/serial_core.h>
20 #include <linux/serial.h>
21 #include <linux/clk.h>
22 #include <linux/delay.h>
23 #include <linux/ktime.h>
24 #include <linux/pinctrl/consumer.h>
25 #include <linux/rational.h>
26 #include <linux/slab.h>
27 #include <linux/of.h>
28 #include <linux/of_device.h>
29 #include <linux/io.h>
30 #include <linux/dma-mapping.h>
31
32 #include <asm/irq.h>
33 #include <linux/platform_data/dma-imx.h>
34
35 #include "serial_mctrl_gpio.h"
36
37 /* Register definitions */
38 #define URXD0 0x0 /* Receiver Register */
39 #define URTX0 0x40 /* Transmitter Register */
40 #define UCR1 0x80 /* Control Register 1 */
41 #define UCR2 0x84 /* Control Register 2 */
42 #define UCR3 0x88 /* Control Register 3 */
43 #define UCR4 0x8c /* Control Register 4 */
44 #define UFCR 0x90 /* FIFO Control Register */
45 #define USR1 0x94 /* Status Register 1 */
46 #define USR2 0x98 /* Status Register 2 */
47 #define UESC 0x9c /* Escape Character Register */
48 #define UTIM 0xa0 /* Escape Timer Register */
49 #define UBIR 0xa4 /* BRM Incremental Register */
50 #define UBMR 0xa8 /* BRM Modulator Register */
51 #define UBRC 0xac /* Baud Rate Count Register */
52 #define IMX21_ONEMS 0xb0 /* One Millisecond register */
53 #define IMX1_UTS 0xd0 /* UART Test Register on i.mx1 */
54 #define IMX21_UTS 0xb4 /* UART Test Register on all other i.mx*/
55
56 /* UART Control Register Bit Fields.*/
57 #define URXD_DUMMY_READ (1<<16)
58 #define URXD_CHARRDY (1<<15)
59 #define URXD_ERR (1<<14)
60 #define URXD_OVRRUN (1<<13)
61 #define URXD_FRMERR (1<<12)
62 #define URXD_BRK (1<<11)
63 #define URXD_PRERR (1<<10)
64 #define URXD_RX_DATA (0xFF<<0)
65 #define UCR1_ADEN (1<<15) /* Auto detect interrupt */
66 #define UCR1_ADBR (1<<14) /* Auto detect baud rate */
67 #define UCR1_TRDYEN (1<<13) /* Transmitter ready interrupt enable */
68 #define UCR1_IDEN (1<<12) /* Idle condition interrupt */
69 #define UCR1_ICD_REG(x) (((x) & 3) << 10) /* idle condition detect */
70 #define UCR1_RRDYEN (1<<9) /* Recv ready interrupt enable */
71 #define UCR1_RXDMAEN (1<<8) /* Recv ready DMA enable */
72 #define UCR1_IREN (1<<7) /* Infrared interface enable */
73 #define UCR1_TXMPTYEN (1<<6) /* Transimitter empty interrupt enable */
74 #define UCR1_RTSDEN (1<<5) /* RTS delta interrupt enable */
75 #define UCR1_SNDBRK (1<<4) /* Send break */
76 #define UCR1_TXDMAEN (1<<3) /* Transmitter ready DMA enable */
77 #define IMX1_UCR1_UARTCLKEN (1<<2) /* UART clock enabled, i.mx1 only */
78 #define UCR1_ATDMAEN (1<<2) /* Aging DMA Timer Enable */
79 #define UCR1_DOZE (1<<1) /* Doze */
80 #define UCR1_UARTEN (1<<0) /* UART enabled */
81 #define UCR2_ESCI (1<<15) /* Escape seq interrupt enable */
82 #define UCR2_IRTS (1<<14) /* Ignore RTS pin */
83 #define UCR2_CTSC (1<<13) /* CTS pin control */
84 #define UCR2_CTS (1<<12) /* Clear to send */
85 #define UCR2_ESCEN (1<<11) /* Escape enable */
86 #define UCR2_PREN (1<<8) /* Parity enable */
87 #define UCR2_PROE (1<<7) /* Parity odd/even */
88 #define UCR2_STPB (1<<6) /* Stop */
89 #define UCR2_WS (1<<5) /* Word size */
90 #define UCR2_RTSEN (1<<4) /* Request to send interrupt enable */
91 #define UCR2_ATEN (1<<3) /* Aging Timer Enable */
92 #define UCR2_TXEN (1<<2) /* Transmitter enabled */
93 #define UCR2_RXEN (1<<1) /* Receiver enabled */
94 #define UCR2_SRST (1<<0) /* SW reset */
95 #define UCR3_DTREN (1<<13) /* DTR interrupt enable */
96 #define UCR3_PARERREN (1<<12) /* Parity enable */
97 #define UCR3_FRAERREN (1<<11) /* Frame error interrupt enable */
98 #define UCR3_DSR (1<<10) /* Data set ready */
99 #define UCR3_DCD (1<<9) /* Data carrier detect */
100 #define UCR3_RI (1<<8) /* Ring indicator */
101 #define UCR3_ADNIMP (1<<7) /* Autobaud Detection Not Improved */
102 #define UCR3_RXDSEN (1<<6) /* Receive status interrupt enable */
103 #define UCR3_AIRINTEN (1<<5) /* Async IR wake interrupt enable */
104 #define UCR3_AWAKEN (1<<4) /* Async wake interrupt enable */
105 #define UCR3_DTRDEN (1<<3) /* Data Terminal Ready Delta Enable. */
106 #define IMX21_UCR3_RXDMUXSEL (1<<2) /* RXD Muxed Input Select */
107 #define UCR3_INVT (1<<1) /* Inverted Infrared transmission */
108 #define UCR3_BPEN (1<<0) /* Preset registers enable */
109 #define UCR4_CTSTL_SHF 10 /* CTS trigger level shift */
110 #define UCR4_CTSTL_MASK 0x3F /* CTS trigger is 6 bits wide */
111 #define UCR4_INVR (1<<9) /* Inverted infrared reception */
112 #define UCR4_ENIRI (1<<8) /* Serial infrared interrupt enable */
113 #define UCR4_WKEN (1<<7) /* Wake interrupt enable */
114 #define UCR4_REF16 (1<<6) /* Ref freq 16 MHz */
115 #define UCR4_IDDMAEN (1<<6) /* DMA IDLE Condition Detected */
116 #define UCR4_IRSC (1<<5) /* IR special case */
117 #define UCR4_TCEN (1<<3) /* Transmit complete interrupt enable */
118 #define UCR4_BKEN (1<<2) /* Break condition interrupt enable */
119 #define UCR4_OREN (1<<1) /* Receiver overrun interrupt enable */
120 #define UCR4_DREN (1<<0) /* Recv data ready interrupt enable */
121 #define UFCR_RXTL_SHF 0 /* Receiver trigger level shift */
122 #define UFCR_DCEDTE (1<<6) /* DCE/DTE mode select */
123 #define UFCR_RFDIV (7<<7) /* Reference freq divider mask */
124 #define UFCR_RFDIV_REG(x) (((x) < 7 ? 6 - (x) : 6) << 7)
125 #define UFCR_TXTL_SHF 10 /* Transmitter trigger level shift */
126 #define USR1_PARITYERR (1<<15) /* Parity error interrupt flag */
127 #define USR1_RTSS (1<<14) /* RTS pin status */
128 #define USR1_TRDY (1<<13) /* Transmitter ready interrupt/dma flag */
129 #define USR1_RTSD (1<<12) /* RTS delta */
130 #define USR1_ESCF (1<<11) /* Escape seq interrupt flag */
131 #define USR1_FRAMERR (1<<10) /* Frame error interrupt flag */
132 #define USR1_RRDY (1<<9) /* Receiver ready interrupt/dma flag */
133 #define USR1_AGTIM (1<<8) /* Ageing timer interrupt flag */
134 #define USR1_DTRD (1<<7) /* DTR Delta */
135 #define USR1_RXDS (1<<6) /* Receiver idle interrupt flag */
136 #define USR1_AIRINT (1<<5) /* Async IR wake interrupt flag */
137 #define USR1_AWAKE (1<<4) /* Aysnc wake interrupt flag */
138 #define USR2_ADET (1<<15) /* Auto baud rate detect complete */
139 #define USR2_TXFE (1<<14) /* Transmit buffer FIFO empty */
140 #define USR2_DTRF (1<<13) /* DTR edge interrupt flag */
141 #define USR2_IDLE (1<<12) /* Idle condition */
142 #define USR2_RIDELT (1<<10) /* Ring Interrupt Delta */
143 #define USR2_RIIN (1<<9) /* Ring Indicator Input */
144 #define USR2_IRINT (1<<8) /* Serial infrared interrupt flag */
145 #define USR2_WAKE (1<<7) /* Wake */
146 #define USR2_DCDIN (1<<5) /* Data Carrier Detect Input */
147 #define USR2_RTSF (1<<4) /* RTS edge interrupt flag */
148 #define USR2_TXDC (1<<3) /* Transmitter complete */
149 #define USR2_BRCD (1<<2) /* Break condition */
150 #define USR2_ORE (1<<1) /* Overrun error */
151 #define USR2_RDR (1<<0) /* Recv data ready */
152 #define UTS_FRCPERR (1<<13) /* Force parity error */
153 #define UTS_LOOP (1<<12) /* Loop tx and rx */
154 #define UTS_TXEMPTY (1<<6) /* TxFIFO empty */
155 #define UTS_RXEMPTY (1<<5) /* RxFIFO empty */
156 #define UTS_TXFULL (1<<4) /* TxFIFO full */
157 #define UTS_RXFULL (1<<3) /* RxFIFO full */
158 #define UTS_SOFTRST (1<<0) /* Software reset */
159
160 /* We've been assigned a range on the "Low-density serial ports" major */
161 #define SERIAL_IMX_MAJOR 207
162 #define MINOR_START 16
163 #define DEV_NAME "ttymxc"
164
165 /*
166 * This determines how often we check the modem status signals
167 * for any change. They generally aren't connected to an IRQ
168 * so we have to poll them. We also check immediately before
169 * filling the TX fifo incase CTS has been dropped.
170 */
171 #define MCTRL_TIMEOUT (250*HZ/1000)
172
173 #define DRIVER_NAME "IMX-uart"
174
175 #define UART_NR 8
176
177 /* i.MX21 type uart runs on all i.mx except i.MX1 and i.MX6q */
178 enum imx_uart_type {
179 IMX1_UART,
180 IMX21_UART,
181 IMX53_UART,
182 IMX6Q_UART,
183 };
184
185 /* device type dependent stuff */
186 struct imx_uart_data {
187 unsigned uts_reg;
188 enum imx_uart_type devtype;
189 };
190
191 enum imx_tx_state {
192 OFF,
193 WAIT_AFTER_RTS,
194 SEND,
195 WAIT_AFTER_SEND,
196 };
197
198 struct imx_port {
199 struct uart_port port;
200 struct timer_list timer;
201 unsigned int old_status;
202 unsigned int have_rtscts:1;
203 unsigned int have_rtsgpio:1;
204 unsigned int dte_mode:1;
205 unsigned int inverted_tx:1;
206 unsigned int inverted_rx:1;
207 struct clk *clk_ipg;
208 struct clk *clk_per;
209 const struct imx_uart_data *devdata;
210
211 struct mctrl_gpios *gpios;
212
213 /* shadow registers */
214 unsigned int ucr1;
215 unsigned int ucr2;
216 unsigned int ucr3;
217 unsigned int ucr4;
218 unsigned int ufcr;
219
220 /* DMA fields */
221 unsigned int dma_is_enabled:1;
222 unsigned int dma_is_rxing:1;
223 unsigned int dma_is_txing:1;
224 struct dma_chan *dma_chan_rx, *dma_chan_tx;
225 struct scatterlist rx_sgl, tx_sgl[2];
226 void *rx_buf;
227 struct circ_buf rx_ring;
228 unsigned int rx_buf_size;
229 unsigned int rx_period_length;
230 unsigned int rx_periods;
231 dma_cookie_t rx_cookie;
232 unsigned int tx_bytes;
233 unsigned int dma_tx_nents;
234 unsigned int saved_reg[10];
235 bool context_saved;
236
237 enum imx_tx_state tx_state;
238 struct hrtimer trigger_start_tx;
239 struct hrtimer trigger_stop_tx;
240 };
241
242 struct imx_port_ucrs {
243 unsigned int ucr1;
244 unsigned int ucr2;
245 unsigned int ucr3;
246 };
247
248 static struct imx_uart_data imx_uart_devdata[] = {
249 [IMX1_UART] = {
250 .uts_reg = IMX1_UTS,
251 .devtype = IMX1_UART,
252 },
253 [IMX21_UART] = {
254 .uts_reg = IMX21_UTS,
255 .devtype = IMX21_UART,
256 },
257 [IMX53_UART] = {
258 .uts_reg = IMX21_UTS,
259 .devtype = IMX53_UART,
260 },
261 [IMX6Q_UART] = {
262 .uts_reg = IMX21_UTS,
263 .devtype = IMX6Q_UART,
264 },
265 };
266
267 static const struct of_device_id imx_uart_dt_ids[] = {
268 { .compatible = "fsl,imx6q-uart", .data = &imx_uart_devdata[IMX6Q_UART], },
269 { .compatible = "fsl,imx53-uart", .data = &imx_uart_devdata[IMX53_UART], },
270 { .compatible = "fsl,imx1-uart", .data = &imx_uart_devdata[IMX1_UART], },
271 { .compatible = "fsl,imx21-uart", .data = &imx_uart_devdata[IMX21_UART], },
272 { /* sentinel */ }
273 };
274 MODULE_DEVICE_TABLE(of, imx_uart_dt_ids);
275
imx_uart_writel(struct imx_port * sport,u32 val,u32 offset)276 static void imx_uart_writel(struct imx_port *sport, u32 val, u32 offset)
277 {
278 switch (offset) {
279 case UCR1:
280 sport->ucr1 = val;
281 break;
282 case UCR2:
283 sport->ucr2 = val;
284 break;
285 case UCR3:
286 sport->ucr3 = val;
287 break;
288 case UCR4:
289 sport->ucr4 = val;
290 break;
291 case UFCR:
292 sport->ufcr = val;
293 break;
294 default:
295 break;
296 }
297 writel(val, sport->port.membase + offset);
298 }
299
imx_uart_readl(struct imx_port * sport,u32 offset)300 static u32 imx_uart_readl(struct imx_port *sport, u32 offset)
301 {
302 switch (offset) {
303 case UCR1:
304 return sport->ucr1;
305 break;
306 case UCR2:
307 /*
308 * UCR2_SRST is the only bit in the cached registers that might
309 * differ from the value that was last written. As it only
310 * automatically becomes one after being cleared, reread
311 * conditionally.
312 */
313 if (!(sport->ucr2 & UCR2_SRST))
314 sport->ucr2 = readl(sport->port.membase + offset);
315 return sport->ucr2;
316 break;
317 case UCR3:
318 return sport->ucr3;
319 break;
320 case UCR4:
321 return sport->ucr4;
322 break;
323 case UFCR:
324 return sport->ufcr;
325 break;
326 default:
327 return readl(sport->port.membase + offset);
328 }
329 }
330
imx_uart_uts_reg(struct imx_port * sport)331 static inline unsigned imx_uart_uts_reg(struct imx_port *sport)
332 {
333 return sport->devdata->uts_reg;
334 }
335
imx_uart_is_imx1(struct imx_port * sport)336 static inline int imx_uart_is_imx1(struct imx_port *sport)
337 {
338 return sport->devdata->devtype == IMX1_UART;
339 }
340
imx_uart_is_imx21(struct imx_port * sport)341 static inline int imx_uart_is_imx21(struct imx_port *sport)
342 {
343 return sport->devdata->devtype == IMX21_UART;
344 }
345
imx_uart_is_imx53(struct imx_port * sport)346 static inline int imx_uart_is_imx53(struct imx_port *sport)
347 {
348 return sport->devdata->devtype == IMX53_UART;
349 }
350
imx_uart_is_imx6q(struct imx_port * sport)351 static inline int imx_uart_is_imx6q(struct imx_port *sport)
352 {
353 return sport->devdata->devtype == IMX6Q_UART;
354 }
355 /*
356 * Save and restore functions for UCR1, UCR2 and UCR3 registers
357 */
358 #if IS_ENABLED(CONFIG_SERIAL_IMX_CONSOLE)
imx_uart_ucrs_save(struct imx_port * sport,struct imx_port_ucrs * ucr)359 static void imx_uart_ucrs_save(struct imx_port *sport,
360 struct imx_port_ucrs *ucr)
361 {
362 /* save control registers */
363 ucr->ucr1 = imx_uart_readl(sport, UCR1);
364 ucr->ucr2 = imx_uart_readl(sport, UCR2);
365 ucr->ucr3 = imx_uart_readl(sport, UCR3);
366 }
367
imx_uart_ucrs_restore(struct imx_port * sport,struct imx_port_ucrs * ucr)368 static void imx_uart_ucrs_restore(struct imx_port *sport,
369 struct imx_port_ucrs *ucr)
370 {
371 /* restore control registers */
372 imx_uart_writel(sport, ucr->ucr1, UCR1);
373 imx_uart_writel(sport, ucr->ucr2, UCR2);
374 imx_uart_writel(sport, ucr->ucr3, UCR3);
375 }
376 #endif
377
378 /* called with port.lock taken and irqs caller dependent */
imx_uart_rts_active(struct imx_port * sport,u32 * ucr2)379 static void imx_uart_rts_active(struct imx_port *sport, u32 *ucr2)
380 {
381 *ucr2 &= ~(UCR2_CTSC | UCR2_CTS);
382
383 sport->port.mctrl |= TIOCM_RTS;
384 mctrl_gpio_set(sport->gpios, sport->port.mctrl);
385 }
386
387 /* called with port.lock taken and irqs caller dependent */
imx_uart_rts_inactive(struct imx_port * sport,u32 * ucr2)388 static void imx_uart_rts_inactive(struct imx_port *sport, u32 *ucr2)
389 {
390 *ucr2 &= ~UCR2_CTSC;
391 *ucr2 |= UCR2_CTS;
392
393 sport->port.mctrl &= ~TIOCM_RTS;
394 mctrl_gpio_set(sport->gpios, sport->port.mctrl);
395 }
396
start_hrtimer_ms(struct hrtimer * hrt,unsigned long msec)397 static void start_hrtimer_ms(struct hrtimer *hrt, unsigned long msec)
398 {
399 hrtimer_start(hrt, ms_to_ktime(msec), HRTIMER_MODE_REL);
400 }
401
402 /* called with port.lock taken and irqs off */
imx_uart_start_rx(struct uart_port * port)403 static void imx_uart_start_rx(struct uart_port *port)
404 {
405 struct imx_port *sport = (struct imx_port *)port;
406 unsigned int ucr1, ucr2;
407
408 ucr1 = imx_uart_readl(sport, UCR1);
409 ucr2 = imx_uart_readl(sport, UCR2);
410
411 ucr2 |= UCR2_RXEN;
412
413 if (sport->dma_is_enabled) {
414 ucr1 |= UCR1_RXDMAEN | UCR1_ATDMAEN;
415 } else {
416 ucr1 |= UCR1_RRDYEN;
417 ucr2 |= UCR2_ATEN;
418 }
419
420 /* Write UCR2 first as it includes RXEN */
421 imx_uart_writel(sport, ucr2, UCR2);
422 imx_uart_writel(sport, ucr1, UCR1);
423 }
424
425 /* called with port.lock taken and irqs off */
imx_uart_stop_tx(struct uart_port * port)426 static void imx_uart_stop_tx(struct uart_port *port)
427 {
428 struct imx_port *sport = (struct imx_port *)port;
429 u32 ucr1, ucr4, usr2;
430
431 if (sport->tx_state == OFF)
432 return;
433
434 /*
435 * We are maybe in the SMP context, so if the DMA TX thread is running
436 * on other cpu, we have to wait for it to finish.
437 */
438 if (sport->dma_is_txing)
439 return;
440
441 ucr1 = imx_uart_readl(sport, UCR1);
442 imx_uart_writel(sport, ucr1 & ~UCR1_TRDYEN, UCR1);
443
444 usr2 = imx_uart_readl(sport, USR2);
445 if (!(usr2 & USR2_TXDC)) {
446 /* The shifter is still busy, so retry once TC triggers */
447 return;
448 }
449
450 ucr4 = imx_uart_readl(sport, UCR4);
451 ucr4 &= ~UCR4_TCEN;
452 imx_uart_writel(sport, ucr4, UCR4);
453
454 /* in rs485 mode disable transmitter */
455 if (port->rs485.flags & SER_RS485_ENABLED) {
456 if (sport->tx_state == SEND) {
457 sport->tx_state = WAIT_AFTER_SEND;
458 start_hrtimer_ms(&sport->trigger_stop_tx,
459 port->rs485.delay_rts_after_send);
460 return;
461 }
462
463 if (sport->tx_state == WAIT_AFTER_RTS ||
464 sport->tx_state == WAIT_AFTER_SEND) {
465 u32 ucr2;
466
467 hrtimer_try_to_cancel(&sport->trigger_start_tx);
468
469 ucr2 = imx_uart_readl(sport, UCR2);
470 if (port->rs485.flags & SER_RS485_RTS_AFTER_SEND)
471 imx_uart_rts_active(sport, &ucr2);
472 else
473 imx_uart_rts_inactive(sport, &ucr2);
474 imx_uart_writel(sport, ucr2, UCR2);
475
476 imx_uart_start_rx(port);
477
478 sport->tx_state = OFF;
479 }
480 } else {
481 sport->tx_state = OFF;
482 }
483 }
484
485 /* called with port.lock taken and irqs off */
imx_uart_stop_rx(struct uart_port * port)486 static void imx_uart_stop_rx(struct uart_port *port)
487 {
488 struct imx_port *sport = (struct imx_port *)port;
489 u32 ucr1, ucr2;
490
491 ucr1 = imx_uart_readl(sport, UCR1);
492 ucr2 = imx_uart_readl(sport, UCR2);
493
494 if (sport->dma_is_enabled) {
495 ucr1 &= ~(UCR1_RXDMAEN | UCR1_ATDMAEN);
496 } else {
497 ucr1 &= ~UCR1_RRDYEN;
498 ucr2 &= ~UCR2_ATEN;
499 }
500 imx_uart_writel(sport, ucr1, UCR1);
501
502 ucr2 &= ~UCR2_RXEN;
503 imx_uart_writel(sport, ucr2, UCR2);
504 }
505
506 /* called with port.lock taken and irqs off */
imx_uart_enable_ms(struct uart_port * port)507 static void imx_uart_enable_ms(struct uart_port *port)
508 {
509 struct imx_port *sport = (struct imx_port *)port;
510
511 mod_timer(&sport->timer, jiffies);
512
513 mctrl_gpio_enable_ms(sport->gpios);
514 }
515
516 static void imx_uart_dma_tx(struct imx_port *sport);
517
518 /* called with port.lock taken and irqs off */
imx_uart_transmit_buffer(struct imx_port * sport)519 static inline void imx_uart_transmit_buffer(struct imx_port *sport)
520 {
521 struct circ_buf *xmit = &sport->port.state->xmit;
522
523 if (sport->port.x_char) {
524 /* Send next char */
525 imx_uart_writel(sport, sport->port.x_char, URTX0);
526 sport->port.icount.tx++;
527 sport->port.x_char = 0;
528 return;
529 }
530
531 if (uart_circ_empty(xmit) || uart_tx_stopped(&sport->port)) {
532 imx_uart_stop_tx(&sport->port);
533 return;
534 }
535
536 if (sport->dma_is_enabled) {
537 u32 ucr1;
538 /*
539 * We've just sent a X-char Ensure the TX DMA is enabled
540 * and the TX IRQ is disabled.
541 **/
542 ucr1 = imx_uart_readl(sport, UCR1);
543 ucr1 &= ~UCR1_TRDYEN;
544 if (sport->dma_is_txing) {
545 ucr1 |= UCR1_TXDMAEN;
546 imx_uart_writel(sport, ucr1, UCR1);
547 } else {
548 imx_uart_writel(sport, ucr1, UCR1);
549 imx_uart_dma_tx(sport);
550 }
551
552 return;
553 }
554
555 while (!uart_circ_empty(xmit) &&
556 !(imx_uart_readl(sport, imx_uart_uts_reg(sport)) & UTS_TXFULL)) {
557 /* send xmit->buf[xmit->tail]
558 * out the port here */
559 imx_uart_writel(sport, xmit->buf[xmit->tail], URTX0);
560 xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
561 sport->port.icount.tx++;
562 }
563
564 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
565 uart_write_wakeup(&sport->port);
566
567 if (uart_circ_empty(xmit))
568 imx_uart_stop_tx(&sport->port);
569 }
570
imx_uart_dma_tx_callback(void * data)571 static void imx_uart_dma_tx_callback(void *data)
572 {
573 struct imx_port *sport = data;
574 struct scatterlist *sgl = &sport->tx_sgl[0];
575 struct circ_buf *xmit = &sport->port.state->xmit;
576 unsigned long flags;
577 u32 ucr1;
578
579 spin_lock_irqsave(&sport->port.lock, flags);
580
581 dma_unmap_sg(sport->port.dev, sgl, sport->dma_tx_nents, DMA_TO_DEVICE);
582
583 ucr1 = imx_uart_readl(sport, UCR1);
584 ucr1 &= ~UCR1_TXDMAEN;
585 imx_uart_writel(sport, ucr1, UCR1);
586
587 /* update the stat */
588 xmit->tail = (xmit->tail + sport->tx_bytes) & (UART_XMIT_SIZE - 1);
589 sport->port.icount.tx += sport->tx_bytes;
590
591 dev_dbg(sport->port.dev, "we finish the TX DMA.\n");
592
593 sport->dma_is_txing = 0;
594
595 if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
596 uart_write_wakeup(&sport->port);
597
598 if (!uart_circ_empty(xmit) && !uart_tx_stopped(&sport->port))
599 imx_uart_dma_tx(sport);
600 else if (sport->port.rs485.flags & SER_RS485_ENABLED) {
601 u32 ucr4 = imx_uart_readl(sport, UCR4);
602 ucr4 |= UCR4_TCEN;
603 imx_uart_writel(sport, ucr4, UCR4);
604 }
605
606 spin_unlock_irqrestore(&sport->port.lock, flags);
607 }
608
609 /* called with port.lock taken and irqs off */
imx_uart_dma_tx(struct imx_port * sport)610 static void imx_uart_dma_tx(struct imx_port *sport)
611 {
612 struct circ_buf *xmit = &sport->port.state->xmit;
613 struct scatterlist *sgl = sport->tx_sgl;
614 struct dma_async_tx_descriptor *desc;
615 struct dma_chan *chan = sport->dma_chan_tx;
616 struct device *dev = sport->port.dev;
617 u32 ucr1, ucr4;
618 int ret;
619
620 if (sport->dma_is_txing)
621 return;
622
623 ucr4 = imx_uart_readl(sport, UCR4);
624 ucr4 &= ~UCR4_TCEN;
625 imx_uart_writel(sport, ucr4, UCR4);
626
627 sport->tx_bytes = uart_circ_chars_pending(xmit);
628
629 if (xmit->tail < xmit->head || xmit->head == 0) {
630 sport->dma_tx_nents = 1;
631 sg_init_one(sgl, xmit->buf + xmit->tail, sport->tx_bytes);
632 } else {
633 sport->dma_tx_nents = 2;
634 sg_init_table(sgl, 2);
635 sg_set_buf(sgl, xmit->buf + xmit->tail,
636 UART_XMIT_SIZE - xmit->tail);
637 sg_set_buf(sgl + 1, xmit->buf, xmit->head);
638 }
639
640 ret = dma_map_sg(dev, sgl, sport->dma_tx_nents, DMA_TO_DEVICE);
641 if (ret == 0) {
642 dev_err(dev, "DMA mapping error for TX.\n");
643 return;
644 }
645 desc = dmaengine_prep_slave_sg(chan, sgl, ret,
646 DMA_MEM_TO_DEV, DMA_PREP_INTERRUPT);
647 if (!desc) {
648 dma_unmap_sg(dev, sgl, sport->dma_tx_nents,
649 DMA_TO_DEVICE);
650 dev_err(dev, "We cannot prepare for the TX slave dma!\n");
651 return;
652 }
653 desc->callback = imx_uart_dma_tx_callback;
654 desc->callback_param = sport;
655
656 dev_dbg(dev, "TX: prepare to send %lu bytes by DMA.\n",
657 uart_circ_chars_pending(xmit));
658
659 ucr1 = imx_uart_readl(sport, UCR1);
660 ucr1 |= UCR1_TXDMAEN;
661 imx_uart_writel(sport, ucr1, UCR1);
662
663 /* fire it */
664 sport->dma_is_txing = 1;
665 dmaengine_submit(desc);
666 dma_async_issue_pending(chan);
667 return;
668 }
669
670 /* called with port.lock taken and irqs off */
imx_uart_start_tx(struct uart_port * port)671 static void imx_uart_start_tx(struct uart_port *port)
672 {
673 struct imx_port *sport = (struct imx_port *)port;
674 u32 ucr1;
675
676 if (!sport->port.x_char && uart_circ_empty(&port->state->xmit))
677 return;
678
679 /*
680 * We cannot simply do nothing here if sport->tx_state == SEND already
681 * because UCR1_TXMPTYEN might already have been cleared in
682 * imx_uart_stop_tx(), but tx_state is still SEND.
683 */
684
685 if (port->rs485.flags & SER_RS485_ENABLED) {
686 if (sport->tx_state == OFF) {
687 u32 ucr2 = imx_uart_readl(sport, UCR2);
688 if (port->rs485.flags & SER_RS485_RTS_ON_SEND)
689 imx_uart_rts_active(sport, &ucr2);
690 else
691 imx_uart_rts_inactive(sport, &ucr2);
692 imx_uart_writel(sport, ucr2, UCR2);
693
694 if (!(port->rs485.flags & SER_RS485_RX_DURING_TX))
695 imx_uart_stop_rx(port);
696
697 sport->tx_state = WAIT_AFTER_RTS;
698 start_hrtimer_ms(&sport->trigger_start_tx,
699 port->rs485.delay_rts_before_send);
700 return;
701 }
702
703 if (sport->tx_state == WAIT_AFTER_SEND
704 || sport->tx_state == WAIT_AFTER_RTS) {
705
706 hrtimer_try_to_cancel(&sport->trigger_stop_tx);
707
708 /*
709 * Enable transmitter and shifter empty irq only if DMA
710 * is off. In the DMA case this is done in the
711 * tx-callback.
712 */
713 if (!sport->dma_is_enabled) {
714 u32 ucr4 = imx_uart_readl(sport, UCR4);
715 ucr4 |= UCR4_TCEN;
716 imx_uart_writel(sport, ucr4, UCR4);
717 }
718
719 sport->tx_state = SEND;
720 }
721 } else {
722 sport->tx_state = SEND;
723 }
724
725 if (!sport->dma_is_enabled) {
726 ucr1 = imx_uart_readl(sport, UCR1);
727 imx_uart_writel(sport, ucr1 | UCR1_TRDYEN, UCR1);
728 }
729
730 if (sport->dma_is_enabled) {
731 if (sport->port.x_char) {
732 /* We have X-char to send, so enable TX IRQ and
733 * disable TX DMA to let TX interrupt to send X-char */
734 ucr1 = imx_uart_readl(sport, UCR1);
735 ucr1 &= ~UCR1_TXDMAEN;
736 ucr1 |= UCR1_TRDYEN;
737 imx_uart_writel(sport, ucr1, UCR1);
738 return;
739 }
740
741 if (!uart_circ_empty(&port->state->xmit) &&
742 !uart_tx_stopped(port))
743 imx_uart_dma_tx(sport);
744 return;
745 }
746 }
747
__imx_uart_rtsint(int irq,void * dev_id)748 static irqreturn_t __imx_uart_rtsint(int irq, void *dev_id)
749 {
750 struct imx_port *sport = dev_id;
751 u32 usr1;
752
753 imx_uart_writel(sport, USR1_RTSD, USR1);
754 usr1 = imx_uart_readl(sport, USR1) & USR1_RTSS;
755 uart_handle_cts_change(&sport->port, !!usr1);
756 wake_up_interruptible(&sport->port.state->port.delta_msr_wait);
757
758 return IRQ_HANDLED;
759 }
760
imx_uart_rtsint(int irq,void * dev_id)761 static irqreturn_t imx_uart_rtsint(int irq, void *dev_id)
762 {
763 struct imx_port *sport = dev_id;
764 irqreturn_t ret;
765
766 spin_lock(&sport->port.lock);
767
768 ret = __imx_uart_rtsint(irq, dev_id);
769
770 spin_unlock(&sport->port.lock);
771
772 return ret;
773 }
774
imx_uart_txint(int irq,void * dev_id)775 static irqreturn_t imx_uart_txint(int irq, void *dev_id)
776 {
777 struct imx_port *sport = dev_id;
778
779 spin_lock(&sport->port.lock);
780 imx_uart_transmit_buffer(sport);
781 spin_unlock(&sport->port.lock);
782 return IRQ_HANDLED;
783 }
784
__imx_uart_rxint(int irq,void * dev_id)785 static irqreturn_t __imx_uart_rxint(int irq, void *dev_id)
786 {
787 struct imx_port *sport = dev_id;
788 unsigned int rx, flg, ignored = 0;
789 struct tty_port *port = &sport->port.state->port;
790
791 while (imx_uart_readl(sport, USR2) & USR2_RDR) {
792 u32 usr2;
793
794 flg = TTY_NORMAL;
795 sport->port.icount.rx++;
796
797 rx = imx_uart_readl(sport, URXD0);
798
799 usr2 = imx_uart_readl(sport, USR2);
800 if (usr2 & USR2_BRCD) {
801 imx_uart_writel(sport, USR2_BRCD, USR2);
802 if (uart_handle_break(&sport->port))
803 continue;
804 }
805
806 if (uart_handle_sysrq_char(&sport->port, (unsigned char)rx))
807 continue;
808
809 if (unlikely(rx & URXD_ERR)) {
810 if (rx & URXD_BRK)
811 sport->port.icount.brk++;
812 else if (rx & URXD_PRERR)
813 sport->port.icount.parity++;
814 else if (rx & URXD_FRMERR)
815 sport->port.icount.frame++;
816 if (rx & URXD_OVRRUN)
817 sport->port.icount.overrun++;
818
819 if (rx & sport->port.ignore_status_mask) {
820 if (++ignored > 100)
821 goto out;
822 continue;
823 }
824
825 rx &= (sport->port.read_status_mask | 0xFF);
826
827 if (rx & URXD_BRK)
828 flg = TTY_BREAK;
829 else if (rx & URXD_PRERR)
830 flg = TTY_PARITY;
831 else if (rx & URXD_FRMERR)
832 flg = TTY_FRAME;
833 if (rx & URXD_OVRRUN)
834 flg = TTY_OVERRUN;
835
836 sport->port.sysrq = 0;
837 }
838
839 if (sport->port.ignore_status_mask & URXD_DUMMY_READ)
840 goto out;
841
842 if (tty_insert_flip_char(port, rx, flg) == 0)
843 sport->port.icount.buf_overrun++;
844 }
845
846 out:
847 tty_flip_buffer_push(port);
848
849 return IRQ_HANDLED;
850 }
851
imx_uart_rxint(int irq,void * dev_id)852 static irqreturn_t imx_uart_rxint(int irq, void *dev_id)
853 {
854 struct imx_port *sport = dev_id;
855 irqreturn_t ret;
856
857 spin_lock(&sport->port.lock);
858
859 ret = __imx_uart_rxint(irq, dev_id);
860
861 spin_unlock(&sport->port.lock);
862
863 return ret;
864 }
865
866 static void imx_uart_clear_rx_errors(struct imx_port *sport);
867
868 /*
869 * We have a modem side uart, so the meanings of RTS and CTS are inverted.
870 */
imx_uart_get_hwmctrl(struct imx_port * sport)871 static unsigned int imx_uart_get_hwmctrl(struct imx_port *sport)
872 {
873 unsigned int tmp = TIOCM_DSR;
874 unsigned usr1 = imx_uart_readl(sport, USR1);
875 unsigned usr2 = imx_uart_readl(sport, USR2);
876
877 if (usr1 & USR1_RTSS)
878 tmp |= TIOCM_CTS;
879
880 /* in DCE mode DCDIN is always 0 */
881 if (!(usr2 & USR2_DCDIN))
882 tmp |= TIOCM_CAR;
883
884 if (sport->dte_mode)
885 if (!(imx_uart_readl(sport, USR2) & USR2_RIIN))
886 tmp |= TIOCM_RI;
887
888 return tmp;
889 }
890
891 /*
892 * Handle any change of modem status signal since we were last called.
893 */
imx_uart_mctrl_check(struct imx_port * sport)894 static void imx_uart_mctrl_check(struct imx_port *sport)
895 {
896 unsigned int status, changed;
897
898 status = imx_uart_get_hwmctrl(sport);
899 changed = status ^ sport->old_status;
900
901 if (changed == 0)
902 return;
903
904 sport->old_status = status;
905
906 if (changed & TIOCM_RI && status & TIOCM_RI)
907 sport->port.icount.rng++;
908 if (changed & TIOCM_DSR)
909 sport->port.icount.dsr++;
910 if (changed & TIOCM_CAR)
911 uart_handle_dcd_change(&sport->port, status & TIOCM_CAR);
912 if (changed & TIOCM_CTS)
913 uart_handle_cts_change(&sport->port, status & TIOCM_CTS);
914
915 wake_up_interruptible(&sport->port.state->port.delta_msr_wait);
916 }
917
imx_uart_int(int irq,void * dev_id)918 static irqreturn_t imx_uart_int(int irq, void *dev_id)
919 {
920 struct imx_port *sport = dev_id;
921 unsigned int usr1, usr2, ucr1, ucr2, ucr3, ucr4;
922 irqreturn_t ret = IRQ_NONE;
923
924 spin_lock(&sport->port.lock);
925
926 usr1 = imx_uart_readl(sport, USR1);
927 usr2 = imx_uart_readl(sport, USR2);
928 ucr1 = imx_uart_readl(sport, UCR1);
929 ucr2 = imx_uart_readl(sport, UCR2);
930 ucr3 = imx_uart_readl(sport, UCR3);
931 ucr4 = imx_uart_readl(sport, UCR4);
932
933 /*
934 * Even if a condition is true that can trigger an irq only handle it if
935 * the respective irq source is enabled. This prevents some undesired
936 * actions, for example if a character that sits in the RX FIFO and that
937 * should be fetched via DMA is tried to be fetched using PIO. Or the
938 * receiver is currently off and so reading from URXD0 results in an
939 * exception. So just mask the (raw) status bits for disabled irqs.
940 */
941 if ((ucr1 & UCR1_RRDYEN) == 0)
942 usr1 &= ~USR1_RRDY;
943 if ((ucr2 & UCR2_ATEN) == 0)
944 usr1 &= ~USR1_AGTIM;
945 if ((ucr1 & UCR1_TRDYEN) == 0)
946 usr1 &= ~USR1_TRDY;
947 if ((ucr4 & UCR4_TCEN) == 0)
948 usr2 &= ~USR2_TXDC;
949 if ((ucr3 & UCR3_DTRDEN) == 0)
950 usr1 &= ~USR1_DTRD;
951 if ((ucr1 & UCR1_RTSDEN) == 0)
952 usr1 &= ~USR1_RTSD;
953 if ((ucr3 & UCR3_AWAKEN) == 0)
954 usr1 &= ~USR1_AWAKE;
955 if ((ucr4 & UCR4_OREN) == 0)
956 usr2 &= ~USR2_ORE;
957
958 if (usr1 & (USR1_RRDY | USR1_AGTIM)) {
959 imx_uart_writel(sport, USR1_AGTIM, USR1);
960
961 __imx_uart_rxint(irq, dev_id);
962 ret = IRQ_HANDLED;
963 }
964
965 if ((usr1 & USR1_TRDY) || (usr2 & USR2_TXDC)) {
966 imx_uart_transmit_buffer(sport);
967 ret = IRQ_HANDLED;
968 }
969
970 if (usr1 & USR1_DTRD) {
971 imx_uart_writel(sport, USR1_DTRD, USR1);
972
973 imx_uart_mctrl_check(sport);
974
975 ret = IRQ_HANDLED;
976 }
977
978 if (usr1 & USR1_RTSD) {
979 __imx_uart_rtsint(irq, dev_id);
980 ret = IRQ_HANDLED;
981 }
982
983 if (usr1 & USR1_AWAKE) {
984 imx_uart_writel(sport, USR1_AWAKE, USR1);
985 ret = IRQ_HANDLED;
986 }
987
988 if (usr2 & USR2_ORE) {
989 sport->port.icount.overrun++;
990 imx_uart_writel(sport, USR2_ORE, USR2);
991 ret = IRQ_HANDLED;
992 }
993
994 spin_unlock(&sport->port.lock);
995
996 return ret;
997 }
998
999 /*
1000 * Return TIOCSER_TEMT when transmitter is not busy.
1001 */
imx_uart_tx_empty(struct uart_port * port)1002 static unsigned int imx_uart_tx_empty(struct uart_port *port)
1003 {
1004 struct imx_port *sport = (struct imx_port *)port;
1005 unsigned int ret;
1006
1007 ret = (imx_uart_readl(sport, USR2) & USR2_TXDC) ? TIOCSER_TEMT : 0;
1008
1009 /* If the TX DMA is working, return 0. */
1010 if (sport->dma_is_txing)
1011 ret = 0;
1012
1013 return ret;
1014 }
1015
1016 /* called with port.lock taken and irqs off */
imx_uart_get_mctrl(struct uart_port * port)1017 static unsigned int imx_uart_get_mctrl(struct uart_port *port)
1018 {
1019 struct imx_port *sport = (struct imx_port *)port;
1020 unsigned int ret = imx_uart_get_hwmctrl(sport);
1021
1022 mctrl_gpio_get(sport->gpios, &ret);
1023
1024 return ret;
1025 }
1026
1027 /* called with port.lock taken and irqs off */
imx_uart_set_mctrl(struct uart_port * port,unsigned int mctrl)1028 static void imx_uart_set_mctrl(struct uart_port *port, unsigned int mctrl)
1029 {
1030 struct imx_port *sport = (struct imx_port *)port;
1031 u32 ucr3, uts;
1032
1033 if (!(port->rs485.flags & SER_RS485_ENABLED)) {
1034 u32 ucr2;
1035
1036 /*
1037 * Turn off autoRTS if RTS is lowered and restore autoRTS
1038 * setting if RTS is raised.
1039 */
1040 ucr2 = imx_uart_readl(sport, UCR2);
1041 ucr2 &= ~(UCR2_CTS | UCR2_CTSC);
1042 if (mctrl & TIOCM_RTS) {
1043 ucr2 |= UCR2_CTS;
1044 /*
1045 * UCR2_IRTS is unset if and only if the port is
1046 * configured for CRTSCTS, so we use inverted UCR2_IRTS
1047 * to get the state to restore to.
1048 */
1049 if (!(ucr2 & UCR2_IRTS))
1050 ucr2 |= UCR2_CTSC;
1051 }
1052 imx_uart_writel(sport, ucr2, UCR2);
1053 }
1054
1055 ucr3 = imx_uart_readl(sport, UCR3) & ~UCR3_DSR;
1056 if (!(mctrl & TIOCM_DTR))
1057 ucr3 |= UCR3_DSR;
1058 imx_uart_writel(sport, ucr3, UCR3);
1059
1060 uts = imx_uart_readl(sport, imx_uart_uts_reg(sport)) & ~UTS_LOOP;
1061 if (mctrl & TIOCM_LOOP)
1062 uts |= UTS_LOOP;
1063 imx_uart_writel(sport, uts, imx_uart_uts_reg(sport));
1064
1065 mctrl_gpio_set(sport->gpios, mctrl);
1066 }
1067
1068 /*
1069 * Interrupts always disabled.
1070 */
imx_uart_break_ctl(struct uart_port * port,int break_state)1071 static void imx_uart_break_ctl(struct uart_port *port, int break_state)
1072 {
1073 struct imx_port *sport = (struct imx_port *)port;
1074 unsigned long flags;
1075 u32 ucr1;
1076
1077 spin_lock_irqsave(&sport->port.lock, flags);
1078
1079 ucr1 = imx_uart_readl(sport, UCR1) & ~UCR1_SNDBRK;
1080
1081 if (break_state != 0)
1082 ucr1 |= UCR1_SNDBRK;
1083
1084 imx_uart_writel(sport, ucr1, UCR1);
1085
1086 spin_unlock_irqrestore(&sport->port.lock, flags);
1087 }
1088
1089 /*
1090 * This is our per-port timeout handler, for checking the
1091 * modem status signals.
1092 */
imx_uart_timeout(struct timer_list * t)1093 static void imx_uart_timeout(struct timer_list *t)
1094 {
1095 struct imx_port *sport = from_timer(sport, t, timer);
1096 unsigned long flags;
1097
1098 if (sport->port.state) {
1099 spin_lock_irqsave(&sport->port.lock, flags);
1100 imx_uart_mctrl_check(sport);
1101 spin_unlock_irqrestore(&sport->port.lock, flags);
1102
1103 mod_timer(&sport->timer, jiffies + MCTRL_TIMEOUT);
1104 }
1105 }
1106
1107 /*
1108 * There are two kinds of RX DMA interrupts(such as in the MX6Q):
1109 * [1] the RX DMA buffer is full.
1110 * [2] the aging timer expires
1111 *
1112 * Condition [2] is triggered when a character has been sitting in the FIFO
1113 * for at least 8 byte durations.
1114 */
imx_uart_dma_rx_callback(void * data)1115 static void imx_uart_dma_rx_callback(void *data)
1116 {
1117 struct imx_port *sport = data;
1118 struct dma_chan *chan = sport->dma_chan_rx;
1119 struct scatterlist *sgl = &sport->rx_sgl;
1120 struct tty_port *port = &sport->port.state->port;
1121 struct dma_tx_state state;
1122 struct circ_buf *rx_ring = &sport->rx_ring;
1123 enum dma_status status;
1124 unsigned int w_bytes = 0;
1125 unsigned int r_bytes;
1126 unsigned int bd_size;
1127
1128 status = dmaengine_tx_status(chan, sport->rx_cookie, &state);
1129
1130 if (status == DMA_ERROR) {
1131 imx_uart_clear_rx_errors(sport);
1132 return;
1133 }
1134
1135 if (!(sport->port.ignore_status_mask & URXD_DUMMY_READ)) {
1136
1137 /*
1138 * The state-residue variable represents the empty space
1139 * relative to the entire buffer. Taking this in consideration
1140 * the head is always calculated base on the buffer total
1141 * length - DMA transaction residue. The UART script from the
1142 * SDMA firmware will jump to the next buffer descriptor,
1143 * once a DMA transaction if finalized (IMX53 RM - A.4.1.2.4).
1144 * Taking this in consideration the tail is always at the
1145 * beginning of the buffer descriptor that contains the head.
1146 */
1147
1148 /* Calculate the head */
1149 rx_ring->head = sg_dma_len(sgl) - state.residue;
1150
1151 /* Calculate the tail. */
1152 bd_size = sg_dma_len(sgl) / sport->rx_periods;
1153 rx_ring->tail = ((rx_ring->head-1) / bd_size) * bd_size;
1154
1155 if (rx_ring->head <= sg_dma_len(sgl) &&
1156 rx_ring->head > rx_ring->tail) {
1157
1158 /* Move data from tail to head */
1159 r_bytes = rx_ring->head - rx_ring->tail;
1160
1161 /* CPU claims ownership of RX DMA buffer */
1162 dma_sync_sg_for_cpu(sport->port.dev, sgl, 1,
1163 DMA_FROM_DEVICE);
1164
1165 w_bytes = tty_insert_flip_string(port,
1166 sport->rx_buf + rx_ring->tail, r_bytes);
1167
1168 /* UART retrieves ownership of RX DMA buffer */
1169 dma_sync_sg_for_device(sport->port.dev, sgl, 1,
1170 DMA_FROM_DEVICE);
1171
1172 if (w_bytes != r_bytes)
1173 sport->port.icount.buf_overrun++;
1174
1175 sport->port.icount.rx += w_bytes;
1176 } else {
1177 WARN_ON(rx_ring->head > sg_dma_len(sgl));
1178 WARN_ON(rx_ring->head <= rx_ring->tail);
1179 }
1180 }
1181
1182 if (w_bytes) {
1183 tty_flip_buffer_push(port);
1184 dev_dbg(sport->port.dev, "We get %d bytes.\n", w_bytes);
1185 }
1186 }
1187
imx_uart_start_rx_dma(struct imx_port * sport)1188 static int imx_uart_start_rx_dma(struct imx_port *sport)
1189 {
1190 struct scatterlist *sgl = &sport->rx_sgl;
1191 struct dma_chan *chan = sport->dma_chan_rx;
1192 struct device *dev = sport->port.dev;
1193 struct dma_async_tx_descriptor *desc;
1194 int ret;
1195
1196 sport->rx_ring.head = 0;
1197 sport->rx_ring.tail = 0;
1198
1199 sg_init_one(sgl, sport->rx_buf, sport->rx_buf_size);
1200 ret = dma_map_sg(dev, sgl, 1, DMA_FROM_DEVICE);
1201 if (ret == 0) {
1202 dev_err(dev, "DMA mapping error for RX.\n");
1203 return -EINVAL;
1204 }
1205
1206 desc = dmaengine_prep_dma_cyclic(chan, sg_dma_address(sgl),
1207 sg_dma_len(sgl), sg_dma_len(sgl) / sport->rx_periods,
1208 DMA_DEV_TO_MEM, DMA_PREP_INTERRUPT);
1209
1210 if (!desc) {
1211 dma_unmap_sg(dev, sgl, 1, DMA_FROM_DEVICE);
1212 dev_err(dev, "We cannot prepare for the RX slave dma!\n");
1213 return -EINVAL;
1214 }
1215 desc->callback = imx_uart_dma_rx_callback;
1216 desc->callback_param = sport;
1217
1218 dev_dbg(dev, "RX: prepare for the DMA.\n");
1219 sport->dma_is_rxing = 1;
1220 sport->rx_cookie = dmaengine_submit(desc);
1221 dma_async_issue_pending(chan);
1222 return 0;
1223 }
1224
imx_uart_clear_rx_errors(struct imx_port * sport)1225 static void imx_uart_clear_rx_errors(struct imx_port *sport)
1226 {
1227 struct tty_port *port = &sport->port.state->port;
1228 u32 usr1, usr2;
1229
1230 usr1 = imx_uart_readl(sport, USR1);
1231 usr2 = imx_uart_readl(sport, USR2);
1232
1233 if (usr2 & USR2_BRCD) {
1234 sport->port.icount.brk++;
1235 imx_uart_writel(sport, USR2_BRCD, USR2);
1236 uart_handle_break(&sport->port);
1237 if (tty_insert_flip_char(port, 0, TTY_BREAK) == 0)
1238 sport->port.icount.buf_overrun++;
1239 tty_flip_buffer_push(port);
1240 } else {
1241 if (usr1 & USR1_FRAMERR) {
1242 sport->port.icount.frame++;
1243 imx_uart_writel(sport, USR1_FRAMERR, USR1);
1244 } else if (usr1 & USR1_PARITYERR) {
1245 sport->port.icount.parity++;
1246 imx_uart_writel(sport, USR1_PARITYERR, USR1);
1247 }
1248 }
1249
1250 if (usr2 & USR2_ORE) {
1251 sport->port.icount.overrun++;
1252 imx_uart_writel(sport, USR2_ORE, USR2);
1253 }
1254
1255 }
1256
1257 #define TXTL_DEFAULT 2 /* reset default */
1258 #define RXTL_DEFAULT 1 /* reset default */
1259 #define TXTL_DMA 8 /* DMA burst setting */
1260 #define RXTL_DMA 9 /* DMA burst setting */
1261
imx_uart_setup_ufcr(struct imx_port * sport,unsigned char txwl,unsigned char rxwl)1262 static void imx_uart_setup_ufcr(struct imx_port *sport,
1263 unsigned char txwl, unsigned char rxwl)
1264 {
1265 unsigned int val;
1266
1267 /* set receiver / transmitter trigger level */
1268 val = imx_uart_readl(sport, UFCR) & (UFCR_RFDIV | UFCR_DCEDTE);
1269 val |= txwl << UFCR_TXTL_SHF | rxwl;
1270 imx_uart_writel(sport, val, UFCR);
1271 }
1272
imx_uart_dma_exit(struct imx_port * sport)1273 static void imx_uart_dma_exit(struct imx_port *sport)
1274 {
1275 if (sport->dma_chan_rx) {
1276 dmaengine_terminate_sync(sport->dma_chan_rx);
1277 dma_release_channel(sport->dma_chan_rx);
1278 sport->dma_chan_rx = NULL;
1279 sport->rx_cookie = -EINVAL;
1280 kfree(sport->rx_buf);
1281 sport->rx_buf = NULL;
1282 }
1283
1284 if (sport->dma_chan_tx) {
1285 dmaengine_terminate_sync(sport->dma_chan_tx);
1286 dma_release_channel(sport->dma_chan_tx);
1287 sport->dma_chan_tx = NULL;
1288 }
1289 }
1290
imx_uart_dma_init(struct imx_port * sport)1291 static int imx_uart_dma_init(struct imx_port *sport)
1292 {
1293 struct dma_slave_config slave_config = {};
1294 struct device *dev = sport->port.dev;
1295 int ret;
1296
1297 /* Prepare for RX : */
1298 sport->dma_chan_rx = dma_request_slave_channel(dev, "rx");
1299 if (!sport->dma_chan_rx) {
1300 dev_dbg(dev, "cannot get the DMA channel.\n");
1301 ret = -EINVAL;
1302 goto err;
1303 }
1304
1305 slave_config.direction = DMA_DEV_TO_MEM;
1306 slave_config.src_addr = sport->port.mapbase + URXD0;
1307 slave_config.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
1308 /* one byte less than the watermark level to enable the aging timer */
1309 slave_config.src_maxburst = RXTL_DMA - 1;
1310 ret = dmaengine_slave_config(sport->dma_chan_rx, &slave_config);
1311 if (ret) {
1312 dev_err(dev, "error in RX dma configuration.\n");
1313 goto err;
1314 }
1315
1316 sport->rx_buf_size = sport->rx_period_length * sport->rx_periods;
1317 sport->rx_buf = kzalloc(sport->rx_buf_size, GFP_KERNEL);
1318 if (!sport->rx_buf) {
1319 ret = -ENOMEM;
1320 goto err;
1321 }
1322 sport->rx_ring.buf = sport->rx_buf;
1323
1324 /* Prepare for TX : */
1325 sport->dma_chan_tx = dma_request_slave_channel(dev, "tx");
1326 if (!sport->dma_chan_tx) {
1327 dev_err(dev, "cannot get the TX DMA channel!\n");
1328 ret = -EINVAL;
1329 goto err;
1330 }
1331
1332 slave_config.direction = DMA_MEM_TO_DEV;
1333 slave_config.dst_addr = sport->port.mapbase + URTX0;
1334 slave_config.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
1335 slave_config.dst_maxburst = TXTL_DMA;
1336 ret = dmaengine_slave_config(sport->dma_chan_tx, &slave_config);
1337 if (ret) {
1338 dev_err(dev, "error in TX dma configuration.");
1339 goto err;
1340 }
1341
1342 return 0;
1343 err:
1344 imx_uart_dma_exit(sport);
1345 return ret;
1346 }
1347
imx_uart_enable_dma(struct imx_port * sport)1348 static void imx_uart_enable_dma(struct imx_port *sport)
1349 {
1350 u32 ucr1;
1351
1352 imx_uart_setup_ufcr(sport, TXTL_DMA, RXTL_DMA);
1353
1354 /* set UCR1 */
1355 ucr1 = imx_uart_readl(sport, UCR1);
1356 ucr1 |= UCR1_RXDMAEN | UCR1_TXDMAEN | UCR1_ATDMAEN;
1357 imx_uart_writel(sport, ucr1, UCR1);
1358
1359 sport->dma_is_enabled = 1;
1360 }
1361
imx_uart_disable_dma(struct imx_port * sport)1362 static void imx_uart_disable_dma(struct imx_port *sport)
1363 {
1364 u32 ucr1;
1365
1366 /* clear UCR1 */
1367 ucr1 = imx_uart_readl(sport, UCR1);
1368 ucr1 &= ~(UCR1_RXDMAEN | UCR1_TXDMAEN | UCR1_ATDMAEN);
1369 imx_uart_writel(sport, ucr1, UCR1);
1370
1371 imx_uart_setup_ufcr(sport, TXTL_DEFAULT, RXTL_DEFAULT);
1372
1373 sport->dma_is_enabled = 0;
1374 }
1375
1376 /* half the RX buffer size */
1377 #define CTSTL 16
1378
imx_uart_startup(struct uart_port * port)1379 static int imx_uart_startup(struct uart_port *port)
1380 {
1381 struct imx_port *sport = (struct imx_port *)port;
1382 int retval, i;
1383 unsigned long flags;
1384 int dma_is_inited = 0;
1385 u32 ucr1, ucr2, ucr3, ucr4;
1386
1387 retval = clk_prepare_enable(sport->clk_per);
1388 if (retval)
1389 return retval;
1390 retval = clk_prepare_enable(sport->clk_ipg);
1391 if (retval) {
1392 clk_disable_unprepare(sport->clk_per);
1393 return retval;
1394 }
1395
1396 imx_uart_setup_ufcr(sport, TXTL_DEFAULT, RXTL_DEFAULT);
1397
1398 /* disable the DREN bit (Data Ready interrupt enable) before
1399 * requesting IRQs
1400 */
1401 ucr4 = imx_uart_readl(sport, UCR4);
1402
1403 /* set the trigger level for CTS */
1404 ucr4 &= ~(UCR4_CTSTL_MASK << UCR4_CTSTL_SHF);
1405 ucr4 |= CTSTL << UCR4_CTSTL_SHF;
1406
1407 imx_uart_writel(sport, ucr4 & ~UCR4_DREN, UCR4);
1408
1409 /* Can we enable the DMA support? */
1410 if (!uart_console(port) && imx_uart_dma_init(sport) == 0)
1411 dma_is_inited = 1;
1412
1413 spin_lock_irqsave(&sport->port.lock, flags);
1414 /* Reset fifo's and state machines */
1415 i = 100;
1416
1417 ucr2 = imx_uart_readl(sport, UCR2);
1418 ucr2 &= ~UCR2_SRST;
1419 imx_uart_writel(sport, ucr2, UCR2);
1420
1421 while (!(imx_uart_readl(sport, UCR2) & UCR2_SRST) && (--i > 0))
1422 udelay(1);
1423
1424 /*
1425 * Finally, clear and enable interrupts
1426 */
1427 imx_uart_writel(sport, USR1_RTSD | USR1_DTRD, USR1);
1428 imx_uart_writel(sport, USR2_ORE, USR2);
1429
1430 ucr1 = imx_uart_readl(sport, UCR1) & ~UCR1_RRDYEN;
1431 ucr1 |= UCR1_UARTEN;
1432 if (sport->have_rtscts)
1433 ucr1 |= UCR1_RTSDEN;
1434
1435 imx_uart_writel(sport, ucr1, UCR1);
1436
1437 ucr4 = imx_uart_readl(sport, UCR4) & ~(UCR4_OREN | UCR4_INVR);
1438 if (!sport->dma_is_enabled)
1439 ucr4 |= UCR4_OREN;
1440 if (sport->inverted_rx)
1441 ucr4 |= UCR4_INVR;
1442 imx_uart_writel(sport, ucr4, UCR4);
1443
1444 ucr3 = imx_uart_readl(sport, UCR3) & ~UCR3_INVT;
1445 /*
1446 * configure tx polarity before enabling tx
1447 */
1448 if (sport->inverted_tx)
1449 ucr3 |= UCR3_INVT;
1450
1451 if (!imx_uart_is_imx1(sport)) {
1452 ucr3 |= UCR3_DTRDEN | UCR3_RI | UCR3_DCD;
1453
1454 if (sport->dte_mode)
1455 /* disable broken interrupts */
1456 ucr3 &= ~(UCR3_RI | UCR3_DCD);
1457 }
1458 imx_uart_writel(sport, ucr3, UCR3);
1459
1460 ucr2 = imx_uart_readl(sport, UCR2) & ~UCR2_ATEN;
1461 ucr2 |= (UCR2_RXEN | UCR2_TXEN);
1462 if (!sport->have_rtscts)
1463 ucr2 |= UCR2_IRTS;
1464 /*
1465 * make sure the edge sensitive RTS-irq is disabled,
1466 * we're using RTSD instead.
1467 */
1468 if (!imx_uart_is_imx1(sport))
1469 ucr2 &= ~UCR2_RTSEN;
1470 imx_uart_writel(sport, ucr2, UCR2);
1471
1472 /*
1473 * Enable modem status interrupts
1474 */
1475 imx_uart_enable_ms(&sport->port);
1476
1477 if (dma_is_inited) {
1478 imx_uart_enable_dma(sport);
1479 imx_uart_start_rx_dma(sport);
1480 } else {
1481 ucr1 = imx_uart_readl(sport, UCR1);
1482 ucr1 |= UCR1_RRDYEN;
1483 imx_uart_writel(sport, ucr1, UCR1);
1484
1485 ucr2 = imx_uart_readl(sport, UCR2);
1486 ucr2 |= UCR2_ATEN;
1487 imx_uart_writel(sport, ucr2, UCR2);
1488 }
1489
1490 spin_unlock_irqrestore(&sport->port.lock, flags);
1491
1492 return 0;
1493 }
1494
imx_uart_shutdown(struct uart_port * port)1495 static void imx_uart_shutdown(struct uart_port *port)
1496 {
1497 struct imx_port *sport = (struct imx_port *)port;
1498 unsigned long flags;
1499 u32 ucr1, ucr2, ucr4;
1500
1501 if (sport->dma_is_enabled) {
1502 dmaengine_terminate_sync(sport->dma_chan_tx);
1503 if (sport->dma_is_txing) {
1504 dma_unmap_sg(sport->port.dev, &sport->tx_sgl[0],
1505 sport->dma_tx_nents, DMA_TO_DEVICE);
1506 sport->dma_is_txing = 0;
1507 }
1508 dmaengine_terminate_sync(sport->dma_chan_rx);
1509 if (sport->dma_is_rxing) {
1510 dma_unmap_sg(sport->port.dev, &sport->rx_sgl,
1511 1, DMA_FROM_DEVICE);
1512 sport->dma_is_rxing = 0;
1513 }
1514
1515 spin_lock_irqsave(&sport->port.lock, flags);
1516 imx_uart_stop_tx(port);
1517 imx_uart_stop_rx(port);
1518 imx_uart_disable_dma(sport);
1519 spin_unlock_irqrestore(&sport->port.lock, flags);
1520 imx_uart_dma_exit(sport);
1521 }
1522
1523 mctrl_gpio_disable_ms(sport->gpios);
1524
1525 spin_lock_irqsave(&sport->port.lock, flags);
1526 ucr2 = imx_uart_readl(sport, UCR2);
1527 ucr2 &= ~(UCR2_TXEN | UCR2_ATEN);
1528 imx_uart_writel(sport, ucr2, UCR2);
1529 spin_unlock_irqrestore(&sport->port.lock, flags);
1530
1531 /*
1532 * Stop our timer.
1533 */
1534 del_timer_sync(&sport->timer);
1535
1536 /*
1537 * Disable all interrupts, port and break condition.
1538 */
1539
1540 spin_lock_irqsave(&sport->port.lock, flags);
1541
1542 ucr1 = imx_uart_readl(sport, UCR1);
1543 ucr1 &= ~(UCR1_TRDYEN | UCR1_RRDYEN | UCR1_RTSDEN | UCR1_UARTEN | UCR1_RXDMAEN | UCR1_ATDMAEN);
1544 imx_uart_writel(sport, ucr1, UCR1);
1545
1546 ucr4 = imx_uart_readl(sport, UCR4);
1547 ucr4 &= ~(UCR4_OREN | UCR4_TCEN);
1548 imx_uart_writel(sport, ucr4, UCR4);
1549
1550 spin_unlock_irqrestore(&sport->port.lock, flags);
1551
1552 clk_disable_unprepare(sport->clk_per);
1553 clk_disable_unprepare(sport->clk_ipg);
1554 }
1555
1556 /* called with port.lock taken and irqs off */
imx_uart_flush_buffer(struct uart_port * port)1557 static void imx_uart_flush_buffer(struct uart_port *port)
1558 {
1559 struct imx_port *sport = (struct imx_port *)port;
1560 struct scatterlist *sgl = &sport->tx_sgl[0];
1561 u32 ucr2;
1562 int i = 100, ubir, ubmr, uts;
1563
1564 if (!sport->dma_chan_tx)
1565 return;
1566
1567 sport->tx_bytes = 0;
1568 dmaengine_terminate_all(sport->dma_chan_tx);
1569 if (sport->dma_is_txing) {
1570 u32 ucr1;
1571
1572 dma_unmap_sg(sport->port.dev, sgl, sport->dma_tx_nents,
1573 DMA_TO_DEVICE);
1574 ucr1 = imx_uart_readl(sport, UCR1);
1575 ucr1 &= ~UCR1_TXDMAEN;
1576 imx_uart_writel(sport, ucr1, UCR1);
1577 sport->dma_is_txing = 0;
1578 }
1579
1580 /*
1581 * According to the Reference Manual description of the UART SRST bit:
1582 *
1583 * "Reset the transmit and receive state machines,
1584 * all FIFOs and register USR1, USR2, UBIR, UBMR, UBRC, URXD, UTXD
1585 * and UTS[6-3]".
1586 *
1587 * We don't need to restore the old values from USR1, USR2, URXD and
1588 * UTXD. UBRC is read only, so only save/restore the other three
1589 * registers.
1590 */
1591 ubir = imx_uart_readl(sport, UBIR);
1592 ubmr = imx_uart_readl(sport, UBMR);
1593 uts = imx_uart_readl(sport, IMX21_UTS);
1594
1595 ucr2 = imx_uart_readl(sport, UCR2);
1596 ucr2 &= ~UCR2_SRST;
1597 imx_uart_writel(sport, ucr2, UCR2);
1598
1599 while (!(imx_uart_readl(sport, UCR2) & UCR2_SRST) && (--i > 0))
1600 udelay(1);
1601
1602 /* Restore the registers */
1603 imx_uart_writel(sport, ubir, UBIR);
1604 imx_uart_writel(sport, ubmr, UBMR);
1605 imx_uart_writel(sport, uts, IMX21_UTS);
1606 }
1607
1608 static void
imx_uart_set_termios(struct uart_port * port,struct ktermios * termios,struct ktermios * old)1609 imx_uart_set_termios(struct uart_port *port, struct ktermios *termios,
1610 struct ktermios *old)
1611 {
1612 struct imx_port *sport = (struct imx_port *)port;
1613 unsigned long flags;
1614 u32 ucr2, old_ucr2, ufcr;
1615 unsigned int baud, quot;
1616 unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8;
1617 unsigned long div;
1618 unsigned long num, denom, old_ubir, old_ubmr;
1619 uint64_t tdiv64;
1620
1621 /*
1622 * We only support CS7 and CS8.
1623 */
1624 while ((termios->c_cflag & CSIZE) != CS7 &&
1625 (termios->c_cflag & CSIZE) != CS8) {
1626 termios->c_cflag &= ~CSIZE;
1627 termios->c_cflag |= old_csize;
1628 old_csize = CS8;
1629 }
1630
1631 del_timer_sync(&sport->timer);
1632
1633 /*
1634 * Ask the core to calculate the divisor for us.
1635 */
1636 baud = uart_get_baud_rate(port, termios, old, 50, port->uartclk / 16);
1637 quot = uart_get_divisor(port, baud);
1638
1639 spin_lock_irqsave(&sport->port.lock, flags);
1640
1641 /*
1642 * Read current UCR2 and save it for future use, then clear all the bits
1643 * except those we will or may need to preserve.
1644 */
1645 old_ucr2 = imx_uart_readl(sport, UCR2);
1646 ucr2 = old_ucr2 & (UCR2_TXEN | UCR2_RXEN | UCR2_ATEN | UCR2_CTS);
1647
1648 ucr2 |= UCR2_SRST | UCR2_IRTS;
1649 if ((termios->c_cflag & CSIZE) == CS8)
1650 ucr2 |= UCR2_WS;
1651
1652 if (!sport->have_rtscts)
1653 termios->c_cflag &= ~CRTSCTS;
1654
1655 if (port->rs485.flags & SER_RS485_ENABLED) {
1656 /*
1657 * RTS is mandatory for rs485 operation, so keep
1658 * it under manual control and keep transmitter
1659 * disabled.
1660 */
1661 if (port->rs485.flags & SER_RS485_RTS_AFTER_SEND)
1662 imx_uart_rts_active(sport, &ucr2);
1663 else
1664 imx_uart_rts_inactive(sport, &ucr2);
1665
1666 } else if (termios->c_cflag & CRTSCTS) {
1667 /*
1668 * Only let receiver control RTS output if we were not requested
1669 * to have RTS inactive (which then should take precedence).
1670 */
1671 if (ucr2 & UCR2_CTS)
1672 ucr2 |= UCR2_CTSC;
1673 }
1674
1675 if (termios->c_cflag & CRTSCTS)
1676 ucr2 &= ~UCR2_IRTS;
1677 if (termios->c_cflag & CSTOPB)
1678 ucr2 |= UCR2_STPB;
1679 if (termios->c_cflag & PARENB) {
1680 ucr2 |= UCR2_PREN;
1681 if (termios->c_cflag & PARODD)
1682 ucr2 |= UCR2_PROE;
1683 }
1684
1685 sport->port.read_status_mask = 0;
1686 if (termios->c_iflag & INPCK)
1687 sport->port.read_status_mask |= (URXD_FRMERR | URXD_PRERR);
1688 if (termios->c_iflag & (BRKINT | PARMRK))
1689 sport->port.read_status_mask |= URXD_BRK;
1690
1691 /*
1692 * Characters to ignore
1693 */
1694 sport->port.ignore_status_mask = 0;
1695 if (termios->c_iflag & IGNPAR)
1696 sport->port.ignore_status_mask |= URXD_PRERR | URXD_FRMERR;
1697 if (termios->c_iflag & IGNBRK) {
1698 sport->port.ignore_status_mask |= URXD_BRK;
1699 /*
1700 * If we're ignoring parity and break indicators,
1701 * ignore overruns too (for real raw support).
1702 */
1703 if (termios->c_iflag & IGNPAR)
1704 sport->port.ignore_status_mask |= URXD_OVRRUN;
1705 }
1706
1707 if ((termios->c_cflag & CREAD) == 0)
1708 sport->port.ignore_status_mask |= URXD_DUMMY_READ;
1709
1710 /*
1711 * Update the per-port timeout.
1712 */
1713 uart_update_timeout(port, termios->c_cflag, baud);
1714
1715 /* custom-baudrate handling */
1716 div = sport->port.uartclk / (baud * 16);
1717 if (baud == 38400 && quot != div)
1718 baud = sport->port.uartclk / (quot * 16);
1719
1720 div = sport->port.uartclk / (baud * 16);
1721 if (div > 7)
1722 div = 7;
1723 if (!div)
1724 div = 1;
1725
1726 rational_best_approximation(16 * div * baud, sport->port.uartclk,
1727 1 << 16, 1 << 16, &num, &denom);
1728
1729 tdiv64 = sport->port.uartclk;
1730 tdiv64 *= num;
1731 do_div(tdiv64, denom * 16 * div);
1732 tty_termios_encode_baud_rate(termios,
1733 (speed_t)tdiv64, (speed_t)tdiv64);
1734
1735 num -= 1;
1736 denom -= 1;
1737
1738 ufcr = imx_uart_readl(sport, UFCR);
1739 ufcr = (ufcr & (~UFCR_RFDIV)) | UFCR_RFDIV_REG(div);
1740 imx_uart_writel(sport, ufcr, UFCR);
1741
1742 /*
1743 * Two registers below should always be written both and in this
1744 * particular order. One consequence is that we need to check if any of
1745 * them changes and then update both. We do need the check for change
1746 * as even writing the same values seem to "restart"
1747 * transmission/receiving logic in the hardware, that leads to data
1748 * breakage even when rate doesn't in fact change. E.g., user switches
1749 * RTS/CTS handshake and suddenly gets broken bytes.
1750 */
1751 old_ubir = imx_uart_readl(sport, UBIR);
1752 old_ubmr = imx_uart_readl(sport, UBMR);
1753 if (old_ubir != num || old_ubmr != denom) {
1754 imx_uart_writel(sport, num, UBIR);
1755 imx_uart_writel(sport, denom, UBMR);
1756 }
1757
1758 if (!imx_uart_is_imx1(sport))
1759 imx_uart_writel(sport, sport->port.uartclk / div / 1000,
1760 IMX21_ONEMS);
1761
1762 imx_uart_writel(sport, ucr2, UCR2);
1763
1764 if (UART_ENABLE_MS(&sport->port, termios->c_cflag))
1765 imx_uart_enable_ms(&sport->port);
1766
1767 spin_unlock_irqrestore(&sport->port.lock, flags);
1768 }
1769
imx_uart_type(struct uart_port * port)1770 static const char *imx_uart_type(struct uart_port *port)
1771 {
1772 struct imx_port *sport = (struct imx_port *)port;
1773
1774 return sport->port.type == PORT_IMX ? "IMX" : NULL;
1775 }
1776
1777 /*
1778 * Configure/autoconfigure the port.
1779 */
imx_uart_config_port(struct uart_port * port,int flags)1780 static void imx_uart_config_port(struct uart_port *port, int flags)
1781 {
1782 struct imx_port *sport = (struct imx_port *)port;
1783
1784 if (flags & UART_CONFIG_TYPE)
1785 sport->port.type = PORT_IMX;
1786 }
1787
1788 /*
1789 * Verify the new serial_struct (for TIOCSSERIAL).
1790 * The only change we allow are to the flags and type, and
1791 * even then only between PORT_IMX and PORT_UNKNOWN
1792 */
1793 static int
imx_uart_verify_port(struct uart_port * port,struct serial_struct * ser)1794 imx_uart_verify_port(struct uart_port *port, struct serial_struct *ser)
1795 {
1796 struct imx_port *sport = (struct imx_port *)port;
1797 int ret = 0;
1798
1799 if (ser->type != PORT_UNKNOWN && ser->type != PORT_IMX)
1800 ret = -EINVAL;
1801 if (sport->port.irq != ser->irq)
1802 ret = -EINVAL;
1803 if (ser->io_type != UPIO_MEM)
1804 ret = -EINVAL;
1805 if (sport->port.uartclk / 16 != ser->baud_base)
1806 ret = -EINVAL;
1807 if (sport->port.mapbase != (unsigned long)ser->iomem_base)
1808 ret = -EINVAL;
1809 if (sport->port.iobase != ser->port)
1810 ret = -EINVAL;
1811 if (ser->hub6 != 0)
1812 ret = -EINVAL;
1813 return ret;
1814 }
1815
1816 #if defined(CONFIG_CONSOLE_POLL)
1817
imx_uart_poll_init(struct uart_port * port)1818 static int imx_uart_poll_init(struct uart_port *port)
1819 {
1820 struct imx_port *sport = (struct imx_port *)port;
1821 unsigned long flags;
1822 u32 ucr1, ucr2;
1823 int retval;
1824
1825 retval = clk_prepare_enable(sport->clk_ipg);
1826 if (retval)
1827 return retval;
1828 retval = clk_prepare_enable(sport->clk_per);
1829 if (retval)
1830 clk_disable_unprepare(sport->clk_ipg);
1831
1832 imx_uart_setup_ufcr(sport, TXTL_DEFAULT, RXTL_DEFAULT);
1833
1834 spin_lock_irqsave(&sport->port.lock, flags);
1835
1836 /*
1837 * Be careful about the order of enabling bits here. First enable the
1838 * receiver (UARTEN + RXEN) and only then the corresponding irqs.
1839 * This prevents that a character that already sits in the RX fifo is
1840 * triggering an irq but the try to fetch it from there results in an
1841 * exception because UARTEN or RXEN is still off.
1842 */
1843 ucr1 = imx_uart_readl(sport, UCR1);
1844 ucr2 = imx_uart_readl(sport, UCR2);
1845
1846 if (imx_uart_is_imx1(sport))
1847 ucr1 |= IMX1_UCR1_UARTCLKEN;
1848
1849 ucr1 |= UCR1_UARTEN;
1850 ucr1 &= ~(UCR1_TRDYEN | UCR1_RTSDEN | UCR1_RRDYEN);
1851
1852 ucr2 |= UCR2_RXEN | UCR2_TXEN;
1853 ucr2 &= ~UCR2_ATEN;
1854
1855 imx_uart_writel(sport, ucr1, UCR1);
1856 imx_uart_writel(sport, ucr2, UCR2);
1857
1858 /* now enable irqs */
1859 imx_uart_writel(sport, ucr1 | UCR1_RRDYEN, UCR1);
1860 imx_uart_writel(sport, ucr2 | UCR2_ATEN, UCR2);
1861
1862 spin_unlock_irqrestore(&sport->port.lock, flags);
1863
1864 return 0;
1865 }
1866
imx_uart_poll_get_char(struct uart_port * port)1867 static int imx_uart_poll_get_char(struct uart_port *port)
1868 {
1869 struct imx_port *sport = (struct imx_port *)port;
1870 if (!(imx_uart_readl(sport, USR2) & USR2_RDR))
1871 return NO_POLL_CHAR;
1872
1873 return imx_uart_readl(sport, URXD0) & URXD_RX_DATA;
1874 }
1875
imx_uart_poll_put_char(struct uart_port * port,unsigned char c)1876 static void imx_uart_poll_put_char(struct uart_port *port, unsigned char c)
1877 {
1878 struct imx_port *sport = (struct imx_port *)port;
1879 unsigned int status;
1880
1881 /* drain */
1882 do {
1883 status = imx_uart_readl(sport, USR1);
1884 } while (~status & USR1_TRDY);
1885
1886 /* write */
1887 imx_uart_writel(sport, c, URTX0);
1888
1889 /* flush */
1890 do {
1891 status = imx_uart_readl(sport, USR2);
1892 } while (~status & USR2_TXDC);
1893 }
1894 #endif
1895
1896 /* called with port.lock taken and irqs off or from .probe without locking */
imx_uart_rs485_config(struct uart_port * port,struct serial_rs485 * rs485conf)1897 static int imx_uart_rs485_config(struct uart_port *port,
1898 struct serial_rs485 *rs485conf)
1899 {
1900 struct imx_port *sport = (struct imx_port *)port;
1901 u32 ucr2;
1902
1903 /* RTS is required to control the transmitter */
1904 if (!sport->have_rtscts && !sport->have_rtsgpio)
1905 rs485conf->flags &= ~SER_RS485_ENABLED;
1906
1907 if (rs485conf->flags & SER_RS485_ENABLED) {
1908 /* Enable receiver if low-active RTS signal is requested */
1909 if (sport->have_rtscts && !sport->have_rtsgpio &&
1910 !(rs485conf->flags & SER_RS485_RTS_ON_SEND))
1911 rs485conf->flags |= SER_RS485_RX_DURING_TX;
1912
1913 /* disable transmitter */
1914 ucr2 = imx_uart_readl(sport, UCR2);
1915 if (rs485conf->flags & SER_RS485_RTS_AFTER_SEND)
1916 imx_uart_rts_active(sport, &ucr2);
1917 else
1918 imx_uart_rts_inactive(sport, &ucr2);
1919 imx_uart_writel(sport, ucr2, UCR2);
1920 }
1921
1922 /* Make sure Rx is enabled in case Tx is active with Rx disabled */
1923 if (!(rs485conf->flags & SER_RS485_ENABLED) ||
1924 rs485conf->flags & SER_RS485_RX_DURING_TX)
1925 imx_uart_start_rx(port);
1926
1927 port->rs485 = *rs485conf;
1928
1929 return 0;
1930 }
1931
1932 static const struct uart_ops imx_uart_pops = {
1933 .tx_empty = imx_uart_tx_empty,
1934 .set_mctrl = imx_uart_set_mctrl,
1935 .get_mctrl = imx_uart_get_mctrl,
1936 .stop_tx = imx_uart_stop_tx,
1937 .start_tx = imx_uart_start_tx,
1938 .stop_rx = imx_uart_stop_rx,
1939 .enable_ms = imx_uart_enable_ms,
1940 .break_ctl = imx_uart_break_ctl,
1941 .startup = imx_uart_startup,
1942 .shutdown = imx_uart_shutdown,
1943 .flush_buffer = imx_uart_flush_buffer,
1944 .set_termios = imx_uart_set_termios,
1945 .type = imx_uart_type,
1946 .config_port = imx_uart_config_port,
1947 .verify_port = imx_uart_verify_port,
1948 #if defined(CONFIG_CONSOLE_POLL)
1949 .poll_init = imx_uart_poll_init,
1950 .poll_get_char = imx_uart_poll_get_char,
1951 .poll_put_char = imx_uart_poll_put_char,
1952 #endif
1953 };
1954
1955 static struct imx_port *imx_uart_ports[UART_NR];
1956
1957 #if IS_ENABLED(CONFIG_SERIAL_IMX_CONSOLE)
imx_uart_console_putchar(struct uart_port * port,int ch)1958 static void imx_uart_console_putchar(struct uart_port *port, int ch)
1959 {
1960 struct imx_port *sport = (struct imx_port *)port;
1961
1962 while (imx_uart_readl(sport, imx_uart_uts_reg(sport)) & UTS_TXFULL)
1963 barrier();
1964
1965 imx_uart_writel(sport, ch, URTX0);
1966 }
1967
1968 /*
1969 * Interrupts are disabled on entering
1970 */
1971 static void
imx_uart_console_write(struct console * co,const char * s,unsigned int count)1972 imx_uart_console_write(struct console *co, const char *s, unsigned int count)
1973 {
1974 struct imx_port *sport = imx_uart_ports[co->index];
1975 struct imx_port_ucrs old_ucr;
1976 unsigned long flags;
1977 unsigned int ucr1;
1978 int locked = 1;
1979
1980 if (sport->port.sysrq)
1981 locked = 0;
1982 else if (oops_in_progress)
1983 locked = spin_trylock_irqsave(&sport->port.lock, flags);
1984 else
1985 spin_lock_irqsave(&sport->port.lock, flags);
1986
1987 /*
1988 * First, save UCR1/2/3 and then disable interrupts
1989 */
1990 imx_uart_ucrs_save(sport, &old_ucr);
1991 ucr1 = old_ucr.ucr1;
1992
1993 if (imx_uart_is_imx1(sport))
1994 ucr1 |= IMX1_UCR1_UARTCLKEN;
1995 ucr1 |= UCR1_UARTEN;
1996 ucr1 &= ~(UCR1_TRDYEN | UCR1_RRDYEN | UCR1_RTSDEN);
1997
1998 imx_uart_writel(sport, ucr1, UCR1);
1999
2000 imx_uart_writel(sport, old_ucr.ucr2 | UCR2_TXEN, UCR2);
2001
2002 uart_console_write(&sport->port, s, count, imx_uart_console_putchar);
2003
2004 /*
2005 * Finally, wait for transmitter to become empty
2006 * and restore UCR1/2/3
2007 */
2008 while (!(imx_uart_readl(sport, USR2) & USR2_TXDC));
2009
2010 imx_uart_ucrs_restore(sport, &old_ucr);
2011
2012 if (locked)
2013 spin_unlock_irqrestore(&sport->port.lock, flags);
2014 }
2015
2016 /*
2017 * If the port was already initialised (eg, by a boot loader),
2018 * try to determine the current setup.
2019 */
2020 static void __init
imx_uart_console_get_options(struct imx_port * sport,int * baud,int * parity,int * bits)2021 imx_uart_console_get_options(struct imx_port *sport, int *baud,
2022 int *parity, int *bits)
2023 {
2024
2025 if (imx_uart_readl(sport, UCR1) & UCR1_UARTEN) {
2026 /* ok, the port was enabled */
2027 unsigned int ucr2, ubir, ubmr, uartclk;
2028 unsigned int baud_raw;
2029 unsigned int ucfr_rfdiv;
2030
2031 ucr2 = imx_uart_readl(sport, UCR2);
2032
2033 *parity = 'n';
2034 if (ucr2 & UCR2_PREN) {
2035 if (ucr2 & UCR2_PROE)
2036 *parity = 'o';
2037 else
2038 *parity = 'e';
2039 }
2040
2041 if (ucr2 & UCR2_WS)
2042 *bits = 8;
2043 else
2044 *bits = 7;
2045
2046 ubir = imx_uart_readl(sport, UBIR) & 0xffff;
2047 ubmr = imx_uart_readl(sport, UBMR) & 0xffff;
2048
2049 ucfr_rfdiv = (imx_uart_readl(sport, UFCR) & UFCR_RFDIV) >> 7;
2050 if (ucfr_rfdiv == 6)
2051 ucfr_rfdiv = 7;
2052 else
2053 ucfr_rfdiv = 6 - ucfr_rfdiv;
2054
2055 uartclk = clk_get_rate(sport->clk_per);
2056 uartclk /= ucfr_rfdiv;
2057
2058 { /*
2059 * The next code provides exact computation of
2060 * baud_raw = round(((uartclk/16) * (ubir + 1)) / (ubmr + 1))
2061 * without need of float support or long long division,
2062 * which would be required to prevent 32bit arithmetic overflow
2063 */
2064 unsigned int mul = ubir + 1;
2065 unsigned int div = 16 * (ubmr + 1);
2066 unsigned int rem = uartclk % div;
2067
2068 baud_raw = (uartclk / div) * mul;
2069 baud_raw += (rem * mul + div / 2) / div;
2070 *baud = (baud_raw + 50) / 100 * 100;
2071 }
2072
2073 if (*baud != baud_raw)
2074 dev_info(sport->port.dev, "Console IMX rounded baud rate from %d to %d\n",
2075 baud_raw, *baud);
2076 }
2077 }
2078
2079 static int __init
imx_uart_console_setup(struct console * co,char * options)2080 imx_uart_console_setup(struct console *co, char *options)
2081 {
2082 struct imx_port *sport;
2083 int baud = 9600;
2084 int bits = 8;
2085 int parity = 'n';
2086 int flow = 'n';
2087 int retval;
2088
2089 /*
2090 * Check whether an invalid uart number has been specified, and
2091 * if so, search for the first available port that does have
2092 * console support.
2093 */
2094 if (co->index == -1 || co->index >= ARRAY_SIZE(imx_uart_ports))
2095 co->index = 0;
2096 sport = imx_uart_ports[co->index];
2097 if (sport == NULL)
2098 return -ENODEV;
2099
2100 /* For setting the registers, we only need to enable the ipg clock. */
2101 retval = clk_prepare_enable(sport->clk_ipg);
2102 if (retval)
2103 goto error_console;
2104
2105 if (options)
2106 uart_parse_options(options, &baud, &parity, &bits, &flow);
2107 else
2108 imx_uart_console_get_options(sport, &baud, &parity, &bits);
2109
2110 imx_uart_setup_ufcr(sport, TXTL_DEFAULT, RXTL_DEFAULT);
2111
2112 retval = uart_set_options(&sport->port, co, baud, parity, bits, flow);
2113
2114 if (retval) {
2115 clk_disable_unprepare(sport->clk_ipg);
2116 goto error_console;
2117 }
2118
2119 retval = clk_prepare_enable(sport->clk_per);
2120 if (retval)
2121 clk_disable_unprepare(sport->clk_ipg);
2122
2123 error_console:
2124 return retval;
2125 }
2126
2127 static struct uart_driver imx_uart_uart_driver;
2128 static struct console imx_uart_console = {
2129 .name = DEV_NAME,
2130 .write = imx_uart_console_write,
2131 .device = uart_console_device,
2132 .setup = imx_uart_console_setup,
2133 .flags = CON_PRINTBUFFER,
2134 .index = -1,
2135 .data = &imx_uart_uart_driver,
2136 };
2137
2138 #define IMX_CONSOLE &imx_uart_console
2139
2140 #else
2141 #define IMX_CONSOLE NULL
2142 #endif
2143
2144 static struct uart_driver imx_uart_uart_driver = {
2145 .owner = THIS_MODULE,
2146 .driver_name = DRIVER_NAME,
2147 .dev_name = DEV_NAME,
2148 .major = SERIAL_IMX_MAJOR,
2149 .minor = MINOR_START,
2150 .nr = ARRAY_SIZE(imx_uart_ports),
2151 .cons = IMX_CONSOLE,
2152 };
2153
imx_trigger_start_tx(struct hrtimer * t)2154 static enum hrtimer_restart imx_trigger_start_tx(struct hrtimer *t)
2155 {
2156 struct imx_port *sport = container_of(t, struct imx_port, trigger_start_tx);
2157 unsigned long flags;
2158
2159 spin_lock_irqsave(&sport->port.lock, flags);
2160 if (sport->tx_state == WAIT_AFTER_RTS)
2161 imx_uart_start_tx(&sport->port);
2162 spin_unlock_irqrestore(&sport->port.lock, flags);
2163
2164 return HRTIMER_NORESTART;
2165 }
2166
imx_trigger_stop_tx(struct hrtimer * t)2167 static enum hrtimer_restart imx_trigger_stop_tx(struct hrtimer *t)
2168 {
2169 struct imx_port *sport = container_of(t, struct imx_port, trigger_stop_tx);
2170 unsigned long flags;
2171
2172 spin_lock_irqsave(&sport->port.lock, flags);
2173 if (sport->tx_state == WAIT_AFTER_SEND)
2174 imx_uart_stop_tx(&sport->port);
2175 spin_unlock_irqrestore(&sport->port.lock, flags);
2176
2177 return HRTIMER_NORESTART;
2178 }
2179
2180 /* Default RX DMA buffer configuration */
2181 #define RX_DMA_PERIODS 16
2182 #define RX_DMA_PERIOD_LEN (PAGE_SIZE / 4)
2183
imx_uart_probe(struct platform_device * pdev)2184 static int imx_uart_probe(struct platform_device *pdev)
2185 {
2186 struct device_node *np = pdev->dev.of_node;
2187 struct imx_port *sport;
2188 void __iomem *base;
2189 u32 dma_buf_conf[2];
2190 int ret = 0;
2191 u32 ucr1;
2192 struct resource *res;
2193 int txirq, rxirq, rtsirq;
2194
2195 sport = devm_kzalloc(&pdev->dev, sizeof(*sport), GFP_KERNEL);
2196 if (!sport)
2197 return -ENOMEM;
2198
2199 sport->devdata = of_device_get_match_data(&pdev->dev);
2200
2201 ret = of_alias_get_id(np, "serial");
2202 if (ret < 0) {
2203 dev_err(&pdev->dev, "failed to get alias id, errno %d\n", ret);
2204 return ret;
2205 }
2206 sport->port.line = ret;
2207
2208 if (of_get_property(np, "uart-has-rtscts", NULL) ||
2209 of_get_property(np, "fsl,uart-has-rtscts", NULL) /* deprecated */)
2210 sport->have_rtscts = 1;
2211
2212 if (of_get_property(np, "fsl,dte-mode", NULL))
2213 sport->dte_mode = 1;
2214
2215 if (of_get_property(np, "rts-gpios", NULL))
2216 sport->have_rtsgpio = 1;
2217
2218 if (of_get_property(np, "fsl,inverted-tx", NULL))
2219 sport->inverted_tx = 1;
2220
2221 if (of_get_property(np, "fsl,inverted-rx", NULL))
2222 sport->inverted_rx = 1;
2223
2224 if (!of_property_read_u32_array(np, "fsl,dma-info", dma_buf_conf, 2)) {
2225 sport->rx_period_length = dma_buf_conf[0];
2226 sport->rx_periods = dma_buf_conf[1];
2227 } else {
2228 sport->rx_period_length = RX_DMA_PERIOD_LEN;
2229 sport->rx_periods = RX_DMA_PERIODS;
2230 }
2231
2232 if (sport->port.line >= ARRAY_SIZE(imx_uart_ports)) {
2233 dev_err(&pdev->dev, "serial%d out of range\n",
2234 sport->port.line);
2235 return -EINVAL;
2236 }
2237
2238 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
2239 base = devm_ioremap_resource(&pdev->dev, res);
2240 if (IS_ERR(base))
2241 return PTR_ERR(base);
2242
2243 rxirq = platform_get_irq(pdev, 0);
2244 if (rxirq < 0)
2245 return rxirq;
2246 txirq = platform_get_irq_optional(pdev, 1);
2247 rtsirq = platform_get_irq_optional(pdev, 2);
2248
2249 sport->port.dev = &pdev->dev;
2250 sport->port.mapbase = res->start;
2251 sport->port.membase = base;
2252 sport->port.type = PORT_IMX;
2253 sport->port.iotype = UPIO_MEM;
2254 sport->port.irq = rxirq;
2255 sport->port.fifosize = 32;
2256 sport->port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_IMX_CONSOLE);
2257 sport->port.ops = &imx_uart_pops;
2258 sport->port.rs485_config = imx_uart_rs485_config;
2259 sport->port.flags = UPF_BOOT_AUTOCONF;
2260 timer_setup(&sport->timer, imx_uart_timeout, 0);
2261
2262 sport->gpios = mctrl_gpio_init(&sport->port, 0);
2263 if (IS_ERR(sport->gpios))
2264 return PTR_ERR(sport->gpios);
2265
2266 sport->clk_ipg = devm_clk_get(&pdev->dev, "ipg");
2267 if (IS_ERR(sport->clk_ipg)) {
2268 ret = PTR_ERR(sport->clk_ipg);
2269 dev_err(&pdev->dev, "failed to get ipg clk: %d\n", ret);
2270 return ret;
2271 }
2272
2273 sport->clk_per = devm_clk_get(&pdev->dev, "per");
2274 if (IS_ERR(sport->clk_per)) {
2275 ret = PTR_ERR(sport->clk_per);
2276 dev_err(&pdev->dev, "failed to get per clk: %d\n", ret);
2277 return ret;
2278 }
2279
2280 sport->port.uartclk = clk_get_rate(sport->clk_per);
2281
2282 /* For register access, we only need to enable the ipg clock. */
2283 ret = clk_prepare_enable(sport->clk_ipg);
2284 if (ret) {
2285 dev_err(&pdev->dev, "failed to enable per clk: %d\n", ret);
2286 return ret;
2287 }
2288
2289 /* initialize shadow register values */
2290 sport->ucr1 = readl(sport->port.membase + UCR1);
2291 sport->ucr2 = readl(sport->port.membase + UCR2);
2292 sport->ucr3 = readl(sport->port.membase + UCR3);
2293 sport->ucr4 = readl(sport->port.membase + UCR4);
2294 sport->ufcr = readl(sport->port.membase + UFCR);
2295
2296 ret = uart_get_rs485_mode(&sport->port);
2297 if (ret) {
2298 clk_disable_unprepare(sport->clk_ipg);
2299 return ret;
2300 }
2301
2302 if (sport->port.rs485.flags & SER_RS485_ENABLED &&
2303 (!sport->have_rtscts && !sport->have_rtsgpio))
2304 dev_err(&pdev->dev, "no RTS control, disabling rs485\n");
2305
2306 /*
2307 * If using the i.MX UART RTS/CTS control then the RTS (CTS_B)
2308 * signal cannot be set low during transmission in case the
2309 * receiver is off (limitation of the i.MX UART IP).
2310 */
2311 if (sport->port.rs485.flags & SER_RS485_ENABLED &&
2312 sport->have_rtscts && !sport->have_rtsgpio &&
2313 (!(sport->port.rs485.flags & SER_RS485_RTS_ON_SEND) &&
2314 !(sport->port.rs485.flags & SER_RS485_RX_DURING_TX)))
2315 dev_err(&pdev->dev,
2316 "low-active RTS not possible when receiver is off, enabling receiver\n");
2317
2318 imx_uart_rs485_config(&sport->port, &sport->port.rs485);
2319
2320 /* Disable interrupts before requesting them */
2321 ucr1 = imx_uart_readl(sport, UCR1);
2322 ucr1 &= ~(UCR1_ADEN | UCR1_TRDYEN | UCR1_IDEN | UCR1_RRDYEN | UCR1_RTSDEN);
2323 imx_uart_writel(sport, ucr1, UCR1);
2324
2325 if (!imx_uart_is_imx1(sport) && sport->dte_mode) {
2326 /*
2327 * The DCEDTE bit changes the direction of DSR, DCD, DTR and RI
2328 * and influences if UCR3_RI and UCR3_DCD changes the level of RI
2329 * and DCD (when they are outputs) or enables the respective
2330 * irqs. So set this bit early, i.e. before requesting irqs.
2331 */
2332 u32 ufcr = imx_uart_readl(sport, UFCR);
2333 if (!(ufcr & UFCR_DCEDTE))
2334 imx_uart_writel(sport, ufcr | UFCR_DCEDTE, UFCR);
2335
2336 /*
2337 * Disable UCR3_RI and UCR3_DCD irqs. They are also not
2338 * enabled later because they cannot be cleared
2339 * (confirmed on i.MX25) which makes them unusable.
2340 */
2341 imx_uart_writel(sport,
2342 IMX21_UCR3_RXDMUXSEL | UCR3_ADNIMP | UCR3_DSR,
2343 UCR3);
2344
2345 } else {
2346 u32 ucr3 = UCR3_DSR;
2347 u32 ufcr = imx_uart_readl(sport, UFCR);
2348 if (ufcr & UFCR_DCEDTE)
2349 imx_uart_writel(sport, ufcr & ~UFCR_DCEDTE, UFCR);
2350
2351 if (!imx_uart_is_imx1(sport))
2352 ucr3 |= IMX21_UCR3_RXDMUXSEL | UCR3_ADNIMP;
2353 imx_uart_writel(sport, ucr3, UCR3);
2354 }
2355
2356 clk_disable_unprepare(sport->clk_ipg);
2357
2358 hrtimer_init(&sport->trigger_start_tx, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
2359 hrtimer_init(&sport->trigger_stop_tx, CLOCK_MONOTONIC, HRTIMER_MODE_REL);
2360 sport->trigger_start_tx.function = imx_trigger_start_tx;
2361 sport->trigger_stop_tx.function = imx_trigger_stop_tx;
2362
2363 /*
2364 * Allocate the IRQ(s) i.MX1 has three interrupts whereas later
2365 * chips only have one interrupt.
2366 */
2367 if (txirq > 0) {
2368 ret = devm_request_irq(&pdev->dev, rxirq, imx_uart_rxint, 0,
2369 dev_name(&pdev->dev), sport);
2370 if (ret) {
2371 dev_err(&pdev->dev, "failed to request rx irq: %d\n",
2372 ret);
2373 return ret;
2374 }
2375
2376 ret = devm_request_irq(&pdev->dev, txirq, imx_uart_txint, 0,
2377 dev_name(&pdev->dev), sport);
2378 if (ret) {
2379 dev_err(&pdev->dev, "failed to request tx irq: %d\n",
2380 ret);
2381 return ret;
2382 }
2383
2384 ret = devm_request_irq(&pdev->dev, rtsirq, imx_uart_rtsint, 0,
2385 dev_name(&pdev->dev), sport);
2386 if (ret) {
2387 dev_err(&pdev->dev, "failed to request rts irq: %d\n",
2388 ret);
2389 return ret;
2390 }
2391 } else {
2392 ret = devm_request_irq(&pdev->dev, rxirq, imx_uart_int, 0,
2393 dev_name(&pdev->dev), sport);
2394 if (ret) {
2395 dev_err(&pdev->dev, "failed to request irq: %d\n", ret);
2396 return ret;
2397 }
2398 }
2399
2400 imx_uart_ports[sport->port.line] = sport;
2401
2402 platform_set_drvdata(pdev, sport);
2403
2404 return uart_add_one_port(&imx_uart_uart_driver, &sport->port);
2405 }
2406
imx_uart_remove(struct platform_device * pdev)2407 static int imx_uart_remove(struct platform_device *pdev)
2408 {
2409 struct imx_port *sport = platform_get_drvdata(pdev);
2410
2411 return uart_remove_one_port(&imx_uart_uart_driver, &sport->port);
2412 }
2413
imx_uart_restore_context(struct imx_port * sport)2414 static void imx_uart_restore_context(struct imx_port *sport)
2415 {
2416 unsigned long flags;
2417
2418 spin_lock_irqsave(&sport->port.lock, flags);
2419 if (!sport->context_saved) {
2420 spin_unlock_irqrestore(&sport->port.lock, flags);
2421 return;
2422 }
2423
2424 imx_uart_writel(sport, sport->saved_reg[4], UFCR);
2425 imx_uart_writel(sport, sport->saved_reg[5], UESC);
2426 imx_uart_writel(sport, sport->saved_reg[6], UTIM);
2427 imx_uart_writel(sport, sport->saved_reg[7], UBIR);
2428 imx_uart_writel(sport, sport->saved_reg[8], UBMR);
2429 imx_uart_writel(sport, sport->saved_reg[9], IMX21_UTS);
2430 imx_uart_writel(sport, sport->saved_reg[0], UCR1);
2431 imx_uart_writel(sport, sport->saved_reg[1] | UCR2_SRST, UCR2);
2432 imx_uart_writel(sport, sport->saved_reg[2], UCR3);
2433 imx_uart_writel(sport, sport->saved_reg[3], UCR4);
2434 sport->context_saved = false;
2435 spin_unlock_irqrestore(&sport->port.lock, flags);
2436 }
2437
imx_uart_save_context(struct imx_port * sport)2438 static void imx_uart_save_context(struct imx_port *sport)
2439 {
2440 unsigned long flags;
2441
2442 /* Save necessary regs */
2443 spin_lock_irqsave(&sport->port.lock, flags);
2444 sport->saved_reg[0] = imx_uart_readl(sport, UCR1);
2445 sport->saved_reg[1] = imx_uart_readl(sport, UCR2);
2446 sport->saved_reg[2] = imx_uart_readl(sport, UCR3);
2447 sport->saved_reg[3] = imx_uart_readl(sport, UCR4);
2448 sport->saved_reg[4] = imx_uart_readl(sport, UFCR);
2449 sport->saved_reg[5] = imx_uart_readl(sport, UESC);
2450 sport->saved_reg[6] = imx_uart_readl(sport, UTIM);
2451 sport->saved_reg[7] = imx_uart_readl(sport, UBIR);
2452 sport->saved_reg[8] = imx_uart_readl(sport, UBMR);
2453 sport->saved_reg[9] = imx_uart_readl(sport, IMX21_UTS);
2454 sport->context_saved = true;
2455 spin_unlock_irqrestore(&sport->port.lock, flags);
2456 }
2457
imx_uart_enable_wakeup(struct imx_port * sport,bool on)2458 static void imx_uart_enable_wakeup(struct imx_port *sport, bool on)
2459 {
2460 u32 ucr3;
2461
2462 ucr3 = imx_uart_readl(sport, UCR3);
2463 if (on) {
2464 imx_uart_writel(sport, USR1_AWAKE, USR1);
2465 ucr3 |= UCR3_AWAKEN;
2466 } else {
2467 ucr3 &= ~UCR3_AWAKEN;
2468 }
2469 imx_uart_writel(sport, ucr3, UCR3);
2470
2471 if (sport->have_rtscts) {
2472 u32 ucr1 = imx_uart_readl(sport, UCR1);
2473 if (on)
2474 ucr1 |= UCR1_RTSDEN;
2475 else
2476 ucr1 &= ~UCR1_RTSDEN;
2477 imx_uart_writel(sport, ucr1, UCR1);
2478 }
2479 }
2480
imx_uart_suspend_noirq(struct device * dev)2481 static int imx_uart_suspend_noirq(struct device *dev)
2482 {
2483 struct imx_port *sport = dev_get_drvdata(dev);
2484
2485 imx_uart_save_context(sport);
2486
2487 clk_disable(sport->clk_ipg);
2488
2489 pinctrl_pm_select_sleep_state(dev);
2490
2491 return 0;
2492 }
2493
imx_uart_resume_noirq(struct device * dev)2494 static int imx_uart_resume_noirq(struct device *dev)
2495 {
2496 struct imx_port *sport = dev_get_drvdata(dev);
2497 int ret;
2498
2499 pinctrl_pm_select_default_state(dev);
2500
2501 ret = clk_enable(sport->clk_ipg);
2502 if (ret)
2503 return ret;
2504
2505 imx_uart_restore_context(sport);
2506
2507 return 0;
2508 }
2509
imx_uart_suspend(struct device * dev)2510 static int imx_uart_suspend(struct device *dev)
2511 {
2512 struct imx_port *sport = dev_get_drvdata(dev);
2513 int ret;
2514
2515 uart_suspend_port(&imx_uart_uart_driver, &sport->port);
2516 disable_irq(sport->port.irq);
2517
2518 ret = clk_prepare_enable(sport->clk_ipg);
2519 if (ret)
2520 return ret;
2521
2522 /* enable wakeup from i.MX UART */
2523 imx_uart_enable_wakeup(sport, true);
2524
2525 return 0;
2526 }
2527
imx_uart_resume(struct device * dev)2528 static int imx_uart_resume(struct device *dev)
2529 {
2530 struct imx_port *sport = dev_get_drvdata(dev);
2531
2532 /* disable wakeup from i.MX UART */
2533 imx_uart_enable_wakeup(sport, false);
2534
2535 uart_resume_port(&imx_uart_uart_driver, &sport->port);
2536 enable_irq(sport->port.irq);
2537
2538 clk_disable_unprepare(sport->clk_ipg);
2539
2540 return 0;
2541 }
2542
imx_uart_freeze(struct device * dev)2543 static int imx_uart_freeze(struct device *dev)
2544 {
2545 struct imx_port *sport = dev_get_drvdata(dev);
2546
2547 uart_suspend_port(&imx_uart_uart_driver, &sport->port);
2548
2549 return clk_prepare_enable(sport->clk_ipg);
2550 }
2551
imx_uart_thaw(struct device * dev)2552 static int imx_uart_thaw(struct device *dev)
2553 {
2554 struct imx_port *sport = dev_get_drvdata(dev);
2555
2556 uart_resume_port(&imx_uart_uart_driver, &sport->port);
2557
2558 clk_disable_unprepare(sport->clk_ipg);
2559
2560 return 0;
2561 }
2562
2563 static const struct dev_pm_ops imx_uart_pm_ops = {
2564 .suspend_noirq = imx_uart_suspend_noirq,
2565 .resume_noirq = imx_uart_resume_noirq,
2566 .freeze_noirq = imx_uart_suspend_noirq,
2567 .restore_noirq = imx_uart_resume_noirq,
2568 .suspend = imx_uart_suspend,
2569 .resume = imx_uart_resume,
2570 .freeze = imx_uart_freeze,
2571 .thaw = imx_uart_thaw,
2572 .restore = imx_uart_thaw,
2573 };
2574
2575 static struct platform_driver imx_uart_platform_driver = {
2576 .probe = imx_uart_probe,
2577 .remove = imx_uart_remove,
2578
2579 .driver = {
2580 .name = "imx-uart",
2581 .of_match_table = imx_uart_dt_ids,
2582 .pm = &imx_uart_pm_ops,
2583 },
2584 };
2585
imx_uart_init(void)2586 static int __init imx_uart_init(void)
2587 {
2588 int ret = uart_register_driver(&imx_uart_uart_driver);
2589
2590 if (ret)
2591 return ret;
2592
2593 ret = platform_driver_register(&imx_uart_platform_driver);
2594 if (ret != 0)
2595 uart_unregister_driver(&imx_uart_uart_driver);
2596
2597 return ret;
2598 }
2599
imx_uart_exit(void)2600 static void __exit imx_uart_exit(void)
2601 {
2602 platform_driver_unregister(&imx_uart_platform_driver);
2603 uart_unregister_driver(&imx_uart_uart_driver);
2604 }
2605
2606 module_init(imx_uart_init);
2607 module_exit(imx_uart_exit);
2608
2609 MODULE_AUTHOR("Sascha Hauer");
2610 MODULE_DESCRIPTION("IMX generic serial port driver");
2611 MODULE_LICENSE("GPL");
2612 MODULE_ALIAS("platform:imx-uart");
2613
