Searched refs:SW1 (Results 1 – 25 of 25) sorted by relevance
| /Linux-v5.15/Documentation/hid/ |
| D | hid-alps.rst | 114 1 0 0 SW6 SW5 SW4 SW3 SW2 SW1
148 SW1-SW6:
164 Byte1 1 1 1 0 1 SW3 SW2 SW1
173 SW1-SW3:
|
| /Linux-v5.15/Documentation/devicetree/bindings/regulator/ |
| D | pv88060.txt | 11 BUCK1, LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7, SW1, SW2, SW3, SW4,
84 SW1 {
|
| /Linux-v5.15/Documentation/networking/ |
| D | arcnet-hardware.rst | 803 < | SW1 | | SW2 | |
829 SW1 1-6: I/O Base Address Select
889 The first six switches in switch group SW1 are used to select one
932 Switches seven through ten of switch group SW1 are used to select the
1063 SW1: DIP-Switches for Station Address
1085 The station address is binary-coded with SW1.
1341 | | 90C65 || SW1 | ____|
1419 The last three switches in switch block SW1 are used to select one
1442 Switches 1-5 of switch block SW1 select the Memory Base address.
1554 < | PROM | | SW1 | A | 2 | ID3
[all …]
|
| /Linux-v5.15/drivers/regulator/ |
| D | pcap-regulator.c | 131 VREG_INFO(SW1, PCAP_REG_SWCTRL, 1, 2, NA, NA),
228 VREG(VAUX4), VREG(VSIM), VREG(VSIM2), VREG(VVIB), VREG(SW1), VREG(SW2),
|
| D | cpcap-regulator.c | 338 CPCAP_REG(SW1, CPCAP_REG_S1C1, CPCAP_REG_ASSIGN2,
414 CPCAP_REG(SW1, CPCAP_REG_S1C1, CPCAP_REG_ASSIGN2,
|
| D | pv88060-regulator.c | 217 PV88060_SW(PV88060, SW1, 5000000),
|
| D | ltc3676.c | 225 LTC3676_LINEAR_REG(SW1, sw1, BUCK1, DVB1A),
|
| D | ltc3589.c | 257 LTC3589_LINEAR_REG(SW1, sw1, B1DTV1),
|
| D | mc13892-regulator.c | 267 MC13892_SW_DEFINE(SW1, sw1, SWITCHERS0, SWITCHERS0, mc13892_sw1),
|
| D | pfuze100-regulator.c | 422 PFUZE3000_SW_REG(PFUZE3001, SW1, PFUZE100_SW1ABVOL, 0x1f, pfuze3000_sw1a),
|
| /Linux-v5.15/arch/arm/boot/dts/ |
| D | at91-kizbox3-hs.dts | 71 SW1 {
72 label = "SW1";
|
| D | r8a7742-iwg21d-q7-dbcm-ca.dts | 217 * Set SW1 switch on camera board to 'OFF' as we are using 8bit mode
249 /* Set SW1 switch on the SOM to 'ON' */
|
| D | imx53-qsrb.dts | 35 regulator-name = "SW1";
|
| D | r7s72100-rskrza1.dts | 42 label = "SW1";
|
| D | sh73a0-kzm9g.dts | 143 label = "SW1";
|
| D | r8a7794-silk.dts | 13 * SW1: 2-1: AK4643
|
| D | r8a7793-gose.dts | 11 * SW1: 1: AK4643
|
| D | r8a7791-koelsch.dts | 13 * SW1: 1: AK4643
|
| D | at91-sam9x60ek.dts | 86 label = "SW1";
|
| D | r8a7790-lager.dts | 13 * SW1: 1: AK4643
|
| /Linux-v5.15/include/linux/mfd/ |
| D | ezx-pcap.h | 130 #define SW1 17 macro
|
| /Linux-v5.15/Documentation/devicetree/bindings/mfd/ |
| D | mc13xxx.txt | 86 sw1 : regulator SW1 (register 24, bit 0)
|
| /Linux-v5.15/Documentation/networking/device_drivers/appletalk/ |
| D | ltpc.rst | 83 SW1 IRQ 4
|
| /Linux-v5.15/arch/arm64/boot/dts/amlogic/ |
| D | meson-sm1-bananapi-m5.dts | 62 label = "SW1";
|
| D | meson-g12b-odroid-n2.dtsi | 603 * The SW1 slide should also be set to the correct position.
|
