Home
last modified time | relevance | path

Searched refs:RXD (Results 1 – 19 of 19) sorted by relevance

/Linux-v5.15/arch/arm/boot/dts/
Dste-dbx5x0-pinctrl.dtsi17 pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */
28 pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */
49 pins = "GPIO4_AH6"; /* RXD */
60 pins = "GPIO4_AH6"; /* RXD */
103 pins = "GPIO29_W2"; /* RXD */
114 pins = "GPIO29_W2"; /* RXD */
548 "GPIO15_AC3", /* RXD */
591 pins = "GPIO196_AG26"; /* RXD */
Dste-href-family-pinctrl.dtsi23 pins = "GPIO218_AH11"; /* RXD */
41 pins = "GPIO218_AH11"; /* RXD */
58 "GPIO218_AH11"; /* RXD */
Dste-hrefprev60.dtsi80 pins = "GPIO145_C13"; /* RXD */
Dsama5d4.dtsi1353 <AT91_PIOE 29 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* RXD */
1362 <AT91_PIOC 25 AT91_PERIPH_C AT91_PINCTRL_PULL_UP /* RXD */
1371 <AT91_PIOD 12 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* RXD */
1386 <AT91_PIOD 16 AT91_PERIPH_A AT91_PINCTRL_PULL_UP /* RXD */
1401 <AT91_PIOB 4 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* RXD - conflicts with G0_CRS, ISI_HSYNC */
1416 <AT91_PIOE 16 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* RXD */
1425 <AT91_PIOE 26 AT91_PERIPH_B AT91_PINCTRL_PULL_UP /* RXD */
Dr7s9210-rza2mevb.dts14 * - RXD = CN17-9,
Dste-hrefv60plus.dtsi369 /* Normally UART1 RXD, now dangling */
Dste-snowball.dts538 pins = "GPIO145_C13"; /* RXD */
/Linux-v5.15/Documentation/devicetree/bindings/net/
Dmediatek-bluetooth.txt58 - pinctrl-0: Should contain UART RXD low when the device is powered up to
66 - boot-gpios: GPIO same to the pin as UART RXD and used to keep LOW when
Dxilinx_axienet.txt47 axis_clk: AXI4-Stream clock for TXD RXD TXC and RXS interfaces
/Linux-v5.15/drivers/spi/
Dspi-mxic.c63 #define RXD 0x24 macro
320 data = readl(mxic->regs + RXD); in mxic_spi_data_xfer()
325 readl(mxic->regs + RXD); in mxic_spi_data_xfer()
/Linux-v5.15/drivers/mtd/nand/raw/
Dmxic_nand.c64 #define RXD 0x24 macro
374 data = readl(nfc->regs + RXD); in mxic_nfc_data_xfer()
/Linux-v5.15/drivers/mailbox/
Dbcm-pdc-mailbox.c71 #define RXD(x, max_mask) XXD((x), (max_mask)) macro
74 #define NEXTRXD(i, max_mask) RXD((i) + 1, (max_mask))
75 #define PREVRXD(i, max_mask) RXD((i) - 1, (max_mask))
77 #define NRXDACTIVE(h, t, max_mask) RXD((t) - (h), (max_mask))
/Linux-v5.15/drivers/net/ethernet/sun/
Dsunhme.c1952 #define RXD(x) printk x macro
1954 #define RXD(x) macro
1973 RXD(("RX<")); in happy_meal_rx()
1981 RXD(("[%d ", elem)); in happy_meal_rx()
1985 RXD(("ERR(%08x)]", flags)); in happy_meal_rx()
2057 RXD(("len=%d csum=%4x]", len, csum)); in happy_meal_rx()
2070 RXD((">")); in happy_meal_rx()
/Linux-v5.15/arch/arm64/boot/dts/rockchip/
Drk3326-odroid-go2.dts540 /* EXT Header(P2): 2(RXD:GPIO1.C0),3(TXD:.C1),4(CTS:.C2),5(RTS:.C3) */
/Linux-v5.15/arch/arm64/boot/dts/freescale/
Dimx8qxp-colibri.dtsi212 /* Colibri optional CAN on UART_A TXD/RXD */
/Linux-v5.15/arch/powerpc/boot/dts/
Dmpc832x_mds.dts11 * 1) On chip U61, lift (disconnect) pins 21 (TXD) and 22 (RXD) from the board.
/Linux-v5.15/Documentation/networking/dsa/
Dsja1105.rst314 In the RMII spec, the PHY can transmit extra out-of-band signals via RXD[1:0].
/Linux-v5.15/Documentation/networking/
Dphy.rst90 for the receive data lines (RXD[3:0]) processed by the PHY device
/Linux-v5.15/Documentation/driver-api/
Dpin-control.rst437 (these are four pins: CLK, RXD, TXD, FRM). In that case, pin B5 can be used as