Home
last modified time | relevance | path

Searched refs:CP (Results 1 – 25 of 59) sorted by relevance

123

/Linux-v5.15/Documentation/driver-api/serial/
Dmoxa-smartio.rst26 CP-102U, CP-102UL, CP-102UF
27 CP-132U-I, CP-132UL,
28 CP-132, CP-132I, CP132S, CP-132IS,
29 (CP-102, CP-102S)
32 CP-104EL,
33 CP-104UL, CP-104JU,
34 CP-134U, CP-134U-I,
36 CP-114, CP-114I, CP-114S, CP-114IS, CP-114UL,
43 CP-118EL, CP-168EL,
44 CP-118U, CP-168U,
/Linux-v5.15/include/linux/
Dasn1_ber_bytecode.h84 #define _tag(CLASS, CP, TAG) ((ASN1_##CLASS << 6) | (ASN1_##CP << 5) | ASN1_##TAG) argument
85 #define _tagn(CLASS, CP, TAG) ((ASN1_##CLASS << 6) | (ASN1_##CP << 5) | TAG) argument
/Linux-v5.15/tools/memory-model/Documentation/
Dcheatsheet.txt14 smp_mb() & synchronize_rcu() CP Y Y Y Y Y Y Y Y
15 Successful full non-void RMW CP Y Y Y Y Y Y Y Y Y Y Y
16 smp_mb__before_atomic() CP Y Y Y a a a a Y
17 smp_mb__after_atomic() CP a a Y Y Y Y Y Y
/Linux-v5.15/scripts/selinux/
Dinstall_policy.sh16 CP=`which checkpolicy`
22 VERS=`$CP -V | awk '{print $1}'`
41 $CP -U allow -M -o policy.$VERS policy.conf
/Linux-v5.15/Documentation/devicetree/bindings/display/ti/
Dti,tpd12s015.txt8 - gpios: CT CP HPD, LS OE and HPD gpios
20 gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>, /* 60, CT CP HPD */
/Linux-v5.15/arch/arm64/boot/dts/marvell/
Darmada-8020.dtsi19 * in CP master is not connected (by package) to the oscillator. So
20 * disable it. However, the RTC clock in CP slave is connected to the
Darmada-8040.dtsi27 * in CP master is not connected (by package) to the oscillator. So
28 * disable it. However, the RTC clock in CP slave is connected to the
Darmada-80x0.dtsi61 /* The 80x0 has two CP blocks, but uses only one block from each. */
/Linux-v5.15/arch/arm/boot/dts/
Dintegratorcp.dts3 * Device Tree for the ARM Integrator/CP platform
10 model = "ARM Integrator/CP";
44 * The Integrator/CP overall clocking architecture can be found in
235 * the same interrupts in all Integrators, but in the CP
269 * These PrimeCells are only available on the Integrator/CP
Dam57xx-beagle-x15-revc.dts13 gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>, /* gpio7_10, CT CP HPD */
Dam57xx-beagle-x15-revb1.dts13 gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>, /* gpio7_10, CT CP HPD */
Dam57xx-beagle-x15.dts14 gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>, /* gpio7_10, CT CP HPD */
/Linux-v5.15/Documentation/s390/
Dmonreader.rst30 location of the monitor DCSS with the Class E privileged CP command Q NSS MAP
33 See also "CP Command and Utility Reference" (SC24-6081-00) for more information
39 You can use the CP command DEF STOR CONFIG to define a "memory hole" in your
75 the same DCSS. The CP command Q MONITOR (Class E privileged) shows the name
94 which data should be collected. This can be done by the CP command MONITOR
95 (Class E privileged), see "CP Command and Utility Reference".
173 module. You can also use the (Class E privileged) CP command Q NSS MAP to
/Linux-v5.15/Documentation/devicetree/bindings/mtd/partitions/
Darm,arm-firmware-suite.txt5 ARM reference designs: Integrator AP, Integrator CP, Versatile AB,
/Linux-v5.15/sound/soc/sprd/
DKconfig16 and other AP/CP subsystem.
/Linux-v5.15/Documentation/devicetree/bindings/sound/
Dsprd-mcdt.txt4 transmission between audio subsystem and other AP/CP subsystem. It
/Linux-v5.15/drivers/s390/char/
DKconfig150 prompt "Support for the z/VM CP interface"
158 int "Memory in MiB reserved for z/VM CP interface"
162 Specify the default amount of memory in MiB reserved for the z/VM CP
/Linux-v5.15/Documentation/devicetree/bindings/interrupt-controller/
Dmarvell,gicp.txt6 located in the Marvell CP110 to turn wired interrupts inside the CP
/Linux-v5.15/arch/arm/mach-integrator/
DKconfig129 bool "Support Integrator/CP platform"
136 Include support for the ARM(R) Integrator CP platform.
/Linux-v5.15/drivers/clk/versatile/
DKconfig11 - Integrator/AP and Integrator/CP
/Linux-v5.15/arch/s390/kernel/
Dsthyi.c27 #define CP 0xc3d7404040404040UL macro
236 case CP: in fill_diag_mac()
267 case CP: in lpar_cpu_inf()
/Linux-v5.15/Documentation/devicetree/bindings/clock/
Dsamsung,s2mps11.txt8 The S2MPS11/13/15 and S5M8767 provide three(AP/CP/BT) buffered 32.768 kHz
/Linux-v5.15/tools/power/cpupower/
DMakefile78 CP = cp -fpR macro
/Linux-v5.15/arch/arm/mm/
Dproc-xsc3.S417 mrc p15, 0, r5, c15, c1, 0 @ CP access reg
435 mcr p15, 0, r5, c15, c1, 0 @ CP access reg
458 mcr p15, 0, r0, c15, c1, 0 @ write CP access register
Dproc-mohawk.S346 mrc p15, 0, r5, c15, c1, 0 @ CP access reg
364 mcr p15, 0, r5, c15, c1, 0 @ CP access reg

123