Searched refs:Active (Results 1 – 25 of 90) sorted by relevance
1234
21 # Active Time 25.422 us 15.253 ms46 # Active Time 20.317 us 12.800 ms67 # Active Time 17.778 us 11.093 ms88 # Active Time 14.827 us 9.430 ms109 # Active Time 12.212 us 7.767 ms130 # Active Time 26.786 us 16.000 ms151 # Active Time 27.044 us 16.097 ms172 # Active Time 22.040 us 16.080 ms193 # Active Time 20.000 us 15.840 ms215 # Active Time 16.162 us 12.800 ms[all …]
19 - sync-on-green-active: Active state of Sync-on-green signal property of the21 0 = Normal Operation (Active Low, Default)24 - field-even-active: Active-high Field ID output polarity control of the bus.27 0 = Normal Operation (Active Low, Default)
11 Active is high.13 Active is high.
14 Active low.16 Active high.
17 Active high with internal pull down resistor.19 Active low with internal pull up resistor.
19 if any. Active low with pull-ip resistor.21 if any. Active high with pull-down resistor.
18 Active is low.20 Active is high.
44 - hsync-active: Active state of the HSYNC signal. Must be <1> (HIGH).45 - vsync-active: Active state of the VSYNC signal. Must be <1> (HIGH).
70 hsync-active = <1>; /* Active high */71 vsync-active = <0>; /* Active low */72 data-active = <1>; /* Active high */117 hsync-active = <1>; /* Active high */118 vsync-active = <0>; /* Active low */119 data-active = <1>; /* Active high */
8 0 = Active high,9 1 = Active low.
21 0 = Active High,22 1 = Active Low.
110 - 0: Active-high (normal).111 - 1: Active-low (inverted).126 - 4: Active high level-sensitive.127 - 8: Active low level-sensitive.
50 hsync-active = <1>; /* Active high */51 vsync-active = <0>; /* Active low */52 data-active = <1>; /* Active high */90 hsync-active = <1>; /* Active high */91 vsync-active = <0>; /* Active low */92 data-active = <1>; /* Active high */
65 hsync-active = <1>; /* Active high */66 vsync-active = <0>; /* Active low */67 data-active = <1>; /* Active high */128 hsync-active = <1>; /* Active high */129 vsync-active = <0>; /* Active low */130 data-active = <1>; /* Active high */
37 hsync-active = <0>; /* Active low */38 vsync-active = <0>; /* Active low */
22 low to power down the board set it to "Active Low", otherwise set23 gpio to "Active High".
24 low to reset the board set it to "Active Low", otherwise set25 gpio to "Active High".
7 Documentation/devicetree/bindings/gpio/gpio.txt. Active low LEDs
8 - reset-gpios: Active-low GPIO output connected to CRESET_B pin. Note
8 Chip Select Active After Transfer feature).
61 interrupts = <1 1>; // IRQ1 Level Active Low.72 interrupts = <1 1>; // IRQ1 Level Active Low.
5 menu "Active energy metering IC"
12 the opposite level disables the WDT. Active level is determined
1 Device-Tree bindings for Active-semi ACT8945A MFD driver
3 Intel(R) Active Management Technology (Intel AMT)7 Active Management Technology (Intel AMT) implemented in firmware running on
