| /Linux-v5.10/Documentation/devicetree/bindings/mfd/ |
| D | mxs-lradc.txt | 10 - fsl,lradc-touchscreen-wires: Number of wires used to connect the touchscreen
13 disabled. 5 wires is valid for i.MX28 SoC only.
29 fsl,lradc-touchscreen-wires = <4>;
41 fsl,lradc-touchscreen-wires = <5>;
|
| /Linux-v5.10/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-temperature-max31856 | 6 such as those caused by broken thermocouple wires.
10 '1' An open circuit such as broken thermocouple wires
12 '0' No open circuit or broken thermocouple wires are detected
|
| /Linux-v5.10/Documentation/devicetree/bindings/input/touchscreen/ |
| D | fsl-mx25-tcq.txt | 11 - fsl,wires: Should be '<4>' or '<5>'
33 fsl,wires = <4>;
|
| D | ti-tsc-adc.txt | 11 ti,wires: Wires refer to application modes i.e. 4/5/8 wire touchscreen
24 connecting wires on touchscreen. We need to provide an
78 ti,wires = <4>;
|
| /Linux-v5.10/drivers/input/touchscreen/ |
| D | ti_am335x_tsc.c | 52 unsigned int wires; member
135 switch (ts_dev->wires) { in titsc_step_config()
162 switch (ts_dev->wires) { in titsc_step_config()
350 err = of_property_read_u32(node, "ti,wires", &ts_dev->wires); in titsc_parse_dt()
353 switch (ts_dev->wires) { in titsc_parse_dt()
|
| D | fsl-imx25-tcq.c | 436 u32 wires; in mx25_tcq_parse_dt() local
445 error = of_property_read_u32(np, "fsl,wires", &wires); in mx25_tcq_parse_dt()
451 if (wires == 4) { in mx25_tcq_parse_dt()
454 dev_err(&pdev->dev, "%u-wire mode not supported\n", wires); in mx25_tcq_parse_dt()
|
| /Linux-v5.10/include/linux/platform_data/ |
| D | mmc-davinci.h | 20 u8 wires; member
|
| D | mmc-omap.h | 46 u8 wires; /* Used for the MMC driver on omap1 and 2420 */ member
|
| /Linux-v5.10/Documentation/devicetree/bindings/display/tilcdc/ |
| D | tilcdc.txt | 25 - "crossed" indicates wiring that has blue and red wires
44 the wires work as they should (LCD_DATA[0:4] is for Blue[3:7]),
|
| /Linux-v5.10/arch/arm/boot/dts/ |
| D | sama5d3xdm.dtsi | 25 atmel,adc-ts-wires = <4>;
|
| D | at91-cosino_mega2560.dts | 23 atmel,adc-ts-wires = <4>;
|
| D | at91sam9x5dm.dtsi | 58 atmel,adc-ts-wires = <4>;
|
| D | imx6ul-ccimx6ulsbcpro.dts | 385 pinctrl_uart2_4wires: uart2grp-4wires {
394 pinctrl_uart3_2wires: uart3grp-2wires {
|
| D | at91-cosino.dtsi | 39 atmel,adc-ts-wires = <4>;
|
| D | imx23-evk.dts | 106 fsl,lradc-touchscreen-wires = <4>;
|
| D | imx28-cfa10058.dts | 79 fsl,lradc-touchscreen-wires = <4>;
|
| D | at91-sama5d4_ma5d4evk.dts | 87 atmel,adc-ts-wires = <4>;
|
| /Linux-v5.10/arch/arm/mach-omap1/ |
| D | devices.c | 91 if (mmc_controller->slots[0].wires == 4 && !cpu_is_omap7xx()) { in omap1_mmc_mux()
107 if (mmc_controller->slots[1].wires == 4) { in omap1_mmc_mux()
|
| /Linux-v5.10/Documentation/devicetree/bindings/iio/adc/ |
| D | at91_adc.txt | 29 - atmel,adc-ts-wires: Number of touchscreen wires. Should be 4 or 5. If this
|
| /Linux-v5.10/drivers/gpu/drm/amd/acp/ |
| D | Kconfig | 12 This adds the ACP (Audio CoProcessor) IP driver and wires
|
| /Linux-v5.10/Documentation/devicetree/bindings/sound/ |
| D | mt6358.txt | 15 channels of PDM signal. 0 means two wires, 1 means one wire. Default
|
| /Linux-v5.10/Documentation/devicetree/bindings/media/i2c/ |
| D | aptina,mt9v111.txt | 8 of image resolution and formats controllable through a simple two-wires
|
| /Linux-v5.10/Documentation/driver-api/gpio/ |
| D | drivers-on-gpio.rst | 26 mouse cable and connect the wires to GPIO lines or solder a mouse connector
49 (two wires, SDA and SCL lines) by hammering (bitbang) two GPIO lines. It will
54 of wires, at least SCK and optionally MISO, MOSI and chip select lines) using
|
| /Linux-v5.10/arch/arm/mach-davinci/ |
| D | board-neuros-osd2.c | 164 .wires = 4,
|
| D | board-dm355-leopard.c | 203 .wires = 4,
|
