| /Linux-v5.10/Documentation/userspace-api/media/rc/ |
| D | lirc-get-send-mode.rst | 34 The mode used for transmitting.
65 - Device does not support transmitting.
|
| D | lirc-get-features.rst | 52 :ref:`LIRC_MODE_PULSE <lirc-mode-pulse>` can only be used for transmitting.
|
| /Linux-v5.10/Documentation/devicetree/bindings/serial/ |
| D | nvidia,tegra194-tcu.txt | 6 for transmitting and one for receiving, that is used to communicate
17 "tx" - Mailbox for transmitting data to hardware UART
|
| /Linux-v5.10/drivers/media/cec/core/ |
| D | cec-adap.c | 378 if (data->adap->transmitting == data) { in cec_data_cancel()
379 data->adap->transmitting = NULL; in cec_data_cancel()
422 if (adap->transmitting) in cec_flush()
423 cec_data_cancel(adap->transmitting, CEC_TX_STATUS_ABORTED); in cec_flush()
512 if (adap->transmitting) { in cec_thread_func()
514 adap->transmitting->msg.len, in cec_thread_func()
515 adap->transmitting->msg.msg); in cec_thread_func()
517 cec_data_cancel(adap->transmitting, in cec_thread_func()
542 adap->transmitting = data; in cec_thread_func()
607 data = adap->transmitting; in cec_transmit_done_ts()
[all …]
|
| /Linux-v5.10/drivers/net/team/ |
| D | Kconfig | 33 Basic mode where port used for transmitting packets is selected in
45 Basic mode where port used for transmitting packets is selected
|
| /Linux-v5.10/Documentation/devicetree/bindings/iio/health/ |
| D | afe4404.txt | 6 - tx-supply : Regulator supply to transmitting LEDs.
|
| D | afe4403.txt | 6 - tx-supply : Regulator supply to transmitting LEDs.
|
| /Linux-v5.10/drivers/media/rc/ |
| D | redrat3.c | 224 bool transmitting; member
238 if (!rr3->transmitting && (code != 0x40)) in redrat3_dump_fw_error()
276 if (!rr3->transmitting) in redrat3_dump_fw_error()
760 if (rr3->transmitting) { in redrat3_transmit_ir()
769 rr3->transmitting = true; in redrat3_transmit_ir()
846 rr3->transmitting = false; in redrat3_transmit_ir()
|
| D | ite-cir.c | 216 bool for_tx = dev->transmitting; in ite_set_carrier_params()
390 dev->transmitting = true; in ite_tx_ir()
504 dev->transmitting = false; in ite_tx_ir()
1319 wait_event_interruptible(dev->tx_ended, !dev->transmitting); in ite_close()
1638 wait_event_interruptible(dev->tx_ended, !dev->transmitting); in ite_suspend()
|
| D | ite-cir.h | 118 bool in_use, transmitting; member
|
| /Linux-v5.10/drivers/usb/class/ |
| D | cdc-acm.h | 104 int transmitting; member
|
| /Linux-v5.10/Documentation/devicetree/bindings/sound/ |
| D | imx-audio-spdif.txt | 15 transmitting function of S/PDIF will be enabled,
|
| /Linux-v5.10/Documentation/devicetree/bindings/media/ |
| D | st-rc.txt | 14 protocol used for transmitting remote control signals. tx-mode should
|
| /Linux-v5.10/Documentation/scsi/ |
| D | cxgb3i.rst | 18 On transmitting, Chelsio S3 h/w computes and inserts the Header and
32 On transmitting, S3 h/w accepts the complete PDU (header + data)
|
| /Linux-v5.10/drivers/net/hippi/ |
| D | Kconfig | 36 transmitting and receiving. This memory cannot be used by any other
|
| /Linux-v5.10/Documentation/userspace-api/media/cec/ |
| D | cec-pin-error-inj.rst | 91 receiving CEC messages and those relating to transmitting CEC messages. In
156 keeps transmitting after the first byte was NACKed.
188 stop transmitting ('Arbitration Lost'). This is very hard to test,
198 This setting changes the behavior of transmitting CEC messages. Normally
291 Just stop transmitting after this bit. If <op> specifies a specific CEC
|
| /Linux-v5.10/Documentation/userspace-api/media/drivers/ |
| D | cx2341x-uapi.rst | 25 transmitting this block the first line of the block on the right to the
33 second line of 8 UV pairs of the top-left block, etc. After transmitting
|
| /Linux-v5.10/Documentation/devicetree/bindings/soc/fsl/cpm_qe/ |
| D | network.txt | 90 slots used for transmitting and receiving.
|
| /Linux-v5.10/Documentation/networking/mac80211_hwsim/ |
| D | mac80211_hwsim.rst | 44 currently enabled and on the same channel as the transmitting
|
| /Linux-v5.10/Documentation/input/ |
| D | userio.rst | 61 Registers the port with the serio driver and begins transmitting data back and
|
| /Linux-v5.10/Documentation/devicetree/bindings/mfd/ |
| D | atmel-usart.txt | 37 - atmel,use-dma-tx: use of PDC or DMA for transmitting data
|
| /Linux-v5.10/include/media/ |
| D | cec.h | 211 struct cec_data *transmitting; member
|
| /Linux-v5.10/Documentation/networking/caif/ |
| D | caif.rst | 133 might be problems transmitting over UART.
|
| /Linux-v5.10/Documentation/driver-api/serial/ |
| D | driver.rst | 126 Stop transmitting characters. This might be due to the CTS
130 The driver should stop transmitting characters as soon as
140 Start transmitting characters.
|
| /Linux-v5.10/drivers/staging/most/Documentation/ |
| D | driver_usage.txt | 205 When transmitting synchronous data the allocated channel width needs to be
223 When transmitting isochronous AVP data the desired packet size needs to be
|
