Searched refs:sends (Results 1 – 25 of 133) sorted by relevance
123456
| /Linux-v5.10/Documentation/networking/ |
| D | can_ucan_protocol.rst | 22 The driver sends device management commands on this endpoint
25 The device sends CAN data frames and CAN error frames
28 The driver sends CAN data frames on the out endpoint
303 error frames (see ``uapi/linux/can/error.h``) and sends it using the
318 - Once Bus OFF recover is completed the device sends an error frame
328 #) Host sends command ``UCAN_COMMAND_RESET``, subcmd 0
329 #) Host sends command ``UCAN_COMMAND_GET``, subcmd ``UCAN_COMMAND_GET_INFO``
330 #) Device sends ``UCAN_IN_DEVICE_INFO``
331 #) Host sends command ``UCAN_OUT_SET_BITTIMING``
332 #) Host sends command ``UCAN_COMMAND_START``, subcmd 0, mode ``UCAN_MODE_BERR_REPORT``
|
| /Linux-v5.10/sound/soc/xilinx/ |
| D | Kconfig | 7 mode, IP receives audio in AES format, extracts PCM and sends
9 encapsulates PCM in AES format and sends AES data.
|
| /Linux-v5.10/Documentation/sound/cards/ |
| D | serial-u16550.rst | 18 sends the nonstandard MIDI command sequence F5 NN, where NN is the substream
37 module parameter is automatically set to 1. The driver sends the same data to
49 the outs module parameter is automatically set to 1. The driver sends
62 Out 3, and midiCnD8 to Out 4. Thus midiCnD15 sends the data to all 4 ports.
63 As a special case, midiCnD0 also sends to all ports, since it is not useful
|
| /Linux-v5.10/Documentation/hid/ |
| D | intel-ish-hid.rst | 193 independent. The sending side sends DMA_XFER message when the message is in
194 the respective host buffer (TX when host client sends, RX when FW client
195 sends). The recipient of DMA message responds with DMA_XFER_ACK, indicating
204 Here ISH acts as busmaster DMA controller. Hence when host sends DMA_XFER,
205 it's request to do host->ISH DMA transfer; when FW sends DMA_XFER, it means
242 - Host sends HOST_START_REQ_CMD, indicating that host ISHTP layer is up.
244 - Host sends HOST_ENUM_REQ_CMD (enumerate FW clients)
247 - For each FW ID found in that bitmap host sends
|
| /Linux-v5.10/Documentation/driver-api/mei/ |
| D | iamt.rst | 45 When a local application sends a message addressed to the local Intel AMT host
89 and sends an event when the heartbeats stop.
91 configures the watchdog and sends the heartbeats.
|
| D | hdcp.rst | 11 according the HDCP 2.2 spec. The Intel graphics sends the created blob
|
| /Linux-v5.10/Documentation/misc-devices/ |
| D | ibmvmc.rst | 152 RDMA of the HMC ID to the hypervisor, and then sends an Interface Open
154 hypervisor receives this information, it sends Add Buffer messages to the
156 connection. Finally, the hypervisor sends an Interface Open Response
181 and then sends a Signal Message. If a write() is attempted before VMC
185 state. When the hypervisor sends a message to the management, the data is
|
| /Linux-v5.10/Documentation/admin-guide/ |
| D | edid.rst | 18 - The monitor sends no or bogus EDID data.
19 - A KVM sends its own EDID data instead of querying the connected monitor.
|
| /Linux-v5.10/Documentation/userspace-api/media/v4l/ |
| D | vidioc-encoder-cmd.rst | 39 ``VIDIOC_ENCODER_CMD`` sends a command to the encoder,
57 call sends an implicit START command to the encoder if it has not been
61 call of a streaming file descriptor sends an implicit immediate STOP to
|
| D | vidioc-decoder-cmd.rst | 39 ``VIDIOC_DECODER_CMD`` sends a command to the decoder,
50 call sends an implicit START command to the decoder if it has not been
54 call of a streaming file descriptor sends an implicit immediate STOP
|
| /Linux-v5.10/Documentation/sparc/ |
| D | adi.rst | 105 first. Hypervisor creates a sun4v error report and sends a
106 resumable error (TT=0x7e) trap to the kernel. The kernel sends
125 exception is sent to the kernel with TT=0x1a. The kernel sends
143 on a memory address, processor sends an MCD disabled trap. This
147 sends the task SIGSEGV signal with following info::
|
| /Linux-v5.10/Documentation/staging/ |
| D | rpmsg.rst | 73 sends a message across to the remote processor on a given channel.
92 sends a message across to the remote processor on a given channel,
117 sends a message across to the remote processor, using the src and dst
139 sends a message across to the remote processor on a given channel.
156 sends a message across to the remote processor on a given channel,
178 sends a message across to the remote processor, using source and
263 The following is a simple rpmsg driver, that sends an "hello!" message
|
| /Linux-v5.10/drivers/hwtracing/stm/ |
| D | Kconfig | 55 This is a kernel space trace source that sends kernel log
64 This is a kernel space trace source that sends periodic
|
| /Linux-v5.10/Documentation/devicetree/bindings/display/ |
| D | snps,arcpgu.txt | 5 framebuffer and sends it to a single digital encoder (usually HDMI).
|
| /Linux-v5.10/Documentation/driver-api/md/ |
| D | md-cluster.rst | 240 performing resync finishes, it sends RESYNCING with an empty range to
263 2. Node 1 sends a NEWDISK message with uuid and slot number
275 8. If node 1 gets the lock, it sends METADATA_UPDATED after
277 9. If not (get "no-new-dev" lock), it fails the operation and sends
319 resync_finish() also sends a BITMAP_NEEDS_SYNC message which
367 This sends a RE_ADD message to all other nodes and then
|
| /Linux-v5.10/fs/notify/fanotify/ |
| D | Kconfig | 9 notification system which differs from inotify in that it sends
|
| /Linux-v5.10/scripts/kconfig/tests/preprocess/builtin_func/ |
| D | Kconfig | 6 # 'warning-if', if the first argument is y, sends the second argument to stderr,
|
| /Linux-v5.10/Documentation/driver-api/ |
| D | ipmb.rst | 19 sends IPMI requests to a device (usually a Satellite Management
21 sends a response back to the BMC.
|
| /Linux-v5.10/Documentation/admin-guide/blockdev/ |
| D | nbd.rst | 10 the client computer wants to read, e.g., /dev/nb0, it sends a
|
| /Linux-v5.10/Documentation/i2c/ |
| D | smbus-protocol.rst | 58 This sends a single bit to the device, at the place of the Rd/Wr bit::
85 This operation is the reverse of Receive Byte: it sends a single byte
163 This command selects a device register (through the Comm byte), sends
211 This command selects a device register (through the Comm byte), sends
|
| /Linux-v5.10/Documentation/devicetree/bindings/input/ |
| D | atmel,maxtouch.txt | 21 - linux,gpio-keymap: When enabled, the SPT_GPIOPWN_T19 object sends messages
|
| /Linux-v5.10/drivers/infiniband/ulp/rtrs/ |
| D | README | 42 On an established session client sends to server write or read messages.
84 3. After all connections of a path are established client sends to server the
129 2. When confirming a write request server sends an "empty" rdma message with
147 2. When confirming a write request server sends an "empty" rdma message with
|
| /Linux-v5.10/Documentation/usb/ |
| D | usbip_protocol.rst | 13 client opens a TCP/IP connection towards the server, and sends an OP_REQ_DEVLIST
15 in one or more pieces at the low level transport layer). The server sends back
34 sends an OP_REQ_IMPORT packet. The server replies with OP_REP_IMPORT. If the
|
| /Linux-v5.10/Documentation/block/ |
| D | cmdline-partition.rst | 38 partition name. Kernel sends uevent with "PARTNAME". Application can
|
| /Linux-v5.10/drivers/platform/chrome/wilco_ec/ |
| D | Kconfig | 29 (such as power state changes) to userspace. The EC sends the events
|
123456
