| /Linux-v5.10/drivers/leds/ |
| D | leds-lt3593.c | 25 int pulses; in lt3593_led_set() local
41 pulses = 32 - (value * 32) / 255; in lt3593_led_set()
43 if (pulses == 0) { in lt3593_led_set()
52 while (pulses--) { in lt3593_led_set()
|
| /Linux-v5.10/drivers/hwmon/ |
| D | pwm-fan.c | 31 atomic_t pulses; member
49 atomic_inc(&ctx->pulses); in pulse_handler()
58 int pulses; in sample_timer() local
61 pulses = atomic_read(&ctx->pulses); in sample_timer()
62 atomic_sub(pulses, &ctx->pulses); in sample_timer()
63 ctx->rpm = (unsigned int)(pulses * 1000 * 60) / in sample_timer()
|
| /Linux-v5.10/Documentation/ABI/testing/ |
| D | sysfs-bus-iio-timer-stm32 | 37 OC4REF rising or falling edges generate pulses.
39 OC6REF rising or falling edges generate pulses.
41 OC4REF or OC6REF rising edges generate pulses.
44 pulses.
46 OC5REF or OC6REF rising edges generate pulses.
49 pulses.
|
| /Linux-v5.10/Documentation/input/devices/ |
| D | walkera0701.rst | 20 pulses from processor to HF part can be found at pin 2 of this connector,
22 modulation pulses to PC, signal pulses must be amplified.
62 Signal pulses
98 (Warning, pulses on ACK are inverted by transistor, irq is raised up on sync
105 values can be sampled between sync pulses.
|
| /Linux-v5.10/Documentation/devicetree/bindings/hwmon/ |
| D | pwm-fan.txt | 17 - pulses-per-revolution : define the tachometer pulses per fan revolution as
56 pulses-per-revolution = <2>;
|
| /Linux-v5.10/drivers/net/wireless/ath/ |
| D | dfs_pri_detector.c | 163 struct list_head *l = &pde->pulses; in pulse_queue_get_tail()
216 list_add(&p->head, &pde->pulses); in pulse_queue_enqueue()
229 list_for_each_entry(p, &pde->pulses, head) { in pseq_handler_create_sequences()
258 list_for_each_entry_continue(p2, &pde->pulses, head) { in pseq_handler_create_sequences()
367 list_for_each_entry_safe(p, p0, &pde->pulses, head) { in pri_detector_reset()
430 INIT_LIST_HEAD(&de->pulses); in pri_detector_init()
|
| D | dfs_pri_detector.h | 70 struct list_head pulses; member
|
| /Linux-v5.10/Documentation/hwmon/ |
| D | g762.rst | 18 hardware characteristics of the system (reference clock, pulses per
36 number of pulses per fan revolution. Supported values
71 system: a reference clock source frequency, a number of pulses per fan
|
| D | sl28cpld.rst | 35 fan1_input Fan RPM. Assuming 2 pulses per revolution.
|
| D | g760a.rst | 23 consecutive speed pulses. The period is defined in terms of clock
|
| D | nsa320.rst | 55 is reduced from 100 us to less than 15 us then data pulses are likely to be
|
| D | dme1737.rst | 163 to the number of pulses per fan revolution that the connected tachometer
165 that generate 2 pulses per revolution. Fan inputs 5-6 also provide a max
296 number of pulses per revolution that
|
| D | smsc47b397.rst | 90 The SIO counts the number of 90kHz (11.111us) pulses per revolution.
|
| D | sysfs-interface.rst | 299 Number of tachometer pulses per fan revolution.
310 the number of pulses. In the absence of such a register (and
311 thus attribute) the value assumed by all devices is 2 pulses
|
| /Linux-v5.10/Documentation/userspace-api/media/rc/ |
| D | lirc-set-send-carrier.rst | 34 Set send carrier used to modulate IR PWM pulses and spaces.
|
| D | lirc-set-rec-carrier.rst | 34 Set receive carrier used to modulate IR PWM pulses and spaces.
|
| /Linux-v5.10/arch/arm/boot/dts/ |
| D | aspeed-bmc-opp-swift.dts | 349 tach-pulses = <2>;
361 tach-pulses = <2>;
373 tach-pulses = <2>;
385 tach-pulses = <2>;
397 tach-pulses = <2>;
|
| D | aspeed-bmc-opp-tacoma.dts | 482 tach-pulses = <2>;
495 tach-pulses = <2>;
508 tach-pulses = <2>;
521 tach-pulses = <2>;
|
| D | aspeed-bmc-ibm-rainier.dts | 729 tach-pulses = <2>;
735 tach-pulses = <2>;
741 tach-pulses = <2>;
747 tach-pulses = <2>;
|
| /Linux-v5.10/Documentation/devicetree/bindings/leds/ |
| D | leds-is31fl319x.txt | 38 by reducing the dury-cycle of pulses and not the current, which
|
| /Linux-v5.10/Documentation/i2c/ |
| D | gpio-fault-injection.rst | 81 register 0x00 (if it has registers) when further clock pulses happen on SCL.
82 This is why bus recovery (up to 9 clock pulses) must either check SDA or send
|
| /Linux-v5.10/drivers/gpu/drm/i915/ |
| D | Kconfig.profile | 28 int "Interval between heartbeat pulses (ms)"
|
| /Linux-v5.10/drivers/leds/trigger/ |
| D | Kconfig | 25 This allows LEDs to blink in one-shot pulses with parameters
|
| /Linux-v5.10/Documentation/devicetree/bindings/memory-controllers/ |
| D | omap-gpmc.txt | 87 - gpmc,cycle2cycle-delay-ns: Delay between chip-select pulses
|
| /Linux-v5.10/drivers/media/rc/ |
| D | Kconfig | 358 Note that this device can only record bursts of 36 IR pulses and
402 wave and pulses.
|
