| /Linux-v5.10/fs/ext4/ |
| D | truncate.h | 30 ext4_lblk_t needed; in ext4_blocks_for_truncate() local
32 needed = inode->i_blocks >> (inode->i_sb->s_blocksize_bits - 9); in ext4_blocks_for_truncate()
40 if (needed < 2) in ext4_blocks_for_truncate()
41 needed = 2; in ext4_blocks_for_truncate()
45 if (needed > EXT4_MAX_TRANS_DATA) in ext4_blocks_for_truncate()
46 needed = EXT4_MAX_TRANS_DATA; in ext4_blocks_for_truncate()
48 return EXT4_DATA_TRANS_BLOCKS(inode->i_sb) + needed; in ext4_blocks_for_truncate()
|
| /Linux-v5.10/tools/testing/selftests/kselftest/ |
| D | prefix.pl | 13 my $needed = 1;
18 if ($needed) {
20 $needed = 0;
23 $needed = 1 if ($char eq "\n");
|
| /Linux-v5.10/Documentation/ABI/testing/ |
| D | sysfs-bus-usb-lvstest | 10 for Link Layer Validation device. It is needed for TD.7.06.
18 and 127. It is needed for TD.7.18, TD.7.19, TD.7.20 and TD.7.21.
26 and 127. It is needed for TD.7.18, TD.7.19, TD.7.20 and TD.7.21.
33 device. It is needed for TD.7.29, TD.7.31, TD.7.34 and TD.7.35.
40 Validation device. It is needed for TD.7.35 and TD.7.36.
47 Validation device. It is needed for TD.7.36.
53 with Link Layer Validation device. It is needed for TD.7.34.
59 device. It may be needed to properly reset an xHCI 1.1 host port if
60 compliance mode needed to be explicitly enabled.
|
| D | configfs-most | 23 (needed for synchronous and isochrnous data)
55 pass parameters needed by some components
78 (needed for synchronous and isochrnous data)
110 pass parameters needed by some components
133 (needed for synchronous and isochrnous data)
165 pass parameters needed by some components
199 (needed for synchronous and isochrnous data)
231 pass parameters needed by some components
|
| /Linux-v5.10/tools/testing/selftests/powerpc/ptrace/ |
| D | perf-hwbreak.c | 80 unsigned long long breaks, needed; in runtestsingle() local
133 needed = 0; in runtestsingle()
135 needed += loop_num; in runtestsingle()
137 needed += loop_num; in runtestsingle()
138 needed = needed * (1 - exclude_user); in runtestsingle()
141 if (breaks != needed) { in runtestsingle()
143 (unsigned long int)ptr, breaks, needed, loop_num, readwriteflag, exclude_user); in runtestsingle()
|
| /Linux-v5.10/drivers/media/usb/gspca/ |
| D | pac207.c | 380 int needed; in sd_pkt_scan() local
384 needed = 5 - sd->header_read; in sd_pkt_scan()
385 if (len >= needed) in sd_pkt_scan()
386 atomic_set(&sd->avg_lum, data[needed - 1]); in sd_pkt_scan()
389 needed = 11 - sd->header_read; in sd_pkt_scan()
390 if (len <= needed) { in sd_pkt_scan()
394 data += needed; in sd_pkt_scan()
395 len -= needed; in sd_pkt_scan()
|
| /Linux-v5.10/Documentation/x86/ |
| D | tsx_async_abort.rst | 46 ucode needed Mitigation is enabled. CPU is affected and MD_CLEAR is not
73 … X 1 Disabled X None needed None needed
88 … 1 X 1 Enabled X None needed None needed
103 …1 X 1 Enabled X None needed None needed
|
| /Linux-v5.10/drivers/misc/sgi-xp/ |
| D | xpc_main.c | 611 xpc_activate_kthreads(struct xpc_channel *ch, int needed) in xpc_activate_kthreads() argument
617 DBUG_ON(needed <= 0); in xpc_activate_kthreads()
620 wakeup = (needed > idle) ? idle : needed; in xpc_activate_kthreads()
621 needed -= wakeup; in xpc_activate_kthreads()
630 if (needed <= 0) in xpc_activate_kthreads()
633 if (needed + assigned > ch->kthreads_assigned_limit) { in xpc_activate_kthreads()
634 needed = ch->kthreads_assigned_limit - assigned; in xpc_activate_kthreads()
635 if (needed <= 0) in xpc_activate_kthreads()
640 needed, ch->partid, ch->number); in xpc_activate_kthreads()
642 xpc_create_kthreads(ch, needed, 0); in xpc_activate_kthreads()
[all …]
|
| /Linux-v5.10/scripts/coccinelle/free/ |
| D | ifnullfree.cocci | 2 /// NULL check before some freeing functions is not needed.
60 cocci.print_main("NULL check before that freeing function is not needed", p)
66 msg = "WARNING: NULL check before some freeing functions is not needed."
|
| /Linux-v5.10/net/sctp/ |
| D | ulpqueue.c | 965 __u16 needed) in sctp_ulpq_renege_list() argument
1005 if (freed >= needed) in sctp_ulpq_renege_list()
1013 static __u16 sctp_ulpq_renege_order(struct sctp_ulpq *ulpq, __u16 needed) in sctp_ulpq_renege_order() argument
1015 return sctp_ulpq_renege_list(ulpq, &ulpq->lobby, needed); in sctp_ulpq_renege_order()
1019 static __u16 sctp_ulpq_renege_frags(struct sctp_ulpq *ulpq, __u16 needed) in sctp_ulpq_renege_frags() argument
1021 return sctp_ulpq_renege_list(ulpq, &ulpq->reasm, needed); in sctp_ulpq_renege_frags()
1080 __u16 needed; in sctp_ulpq_renege() local
1082 needed = ntohs(chunk->chunk_hdr->length) - in sctp_ulpq_renege()
1086 freed = sctp_ulpq_renege_order(ulpq, needed); in sctp_ulpq_renege()
1087 if (freed < needed) in sctp_ulpq_renege()
[all …]
|
| /Linux-v5.10/drivers/clk/sunxi/ |
| D | Kconfig | 26 usually needed for the PMIC communication, mostly.
34 Those are usually needed for the PMIC communication,
42 usually needed for the PMIC communication, mostly.
|
| /Linux-v5.10/Documentation/arm/omap/ |
| D | omap.rst | 11 v4.3+ Update is needed for custom .config files to make sure
15 v4.18+ Update is needed for custom .config files to make sure
|
| /Linux-v5.10/Documentation/devicetree/bindings/spi/ |
| D | spi_oc_tiny.txt | 11 The clock-frequency and baud-width properties are needed only if the divider
12 is programmable. They are not needed if the divider is fixed.
|
| /Linux-v5.10/drivers/gpu/host1x/ |
| D | cdma.c | 237 unsigned int needed) in host1x_cdma_wait_pushbuffer_space() argument
244 if (space >= needed) in host1x_cdma_wait_pushbuffer_space()
562 unsigned int needed = 2, extra = 0, i; in host1x_cdma_push_wide() local
572 needed += extra; in host1x_cdma_push_wide()
575 host1x_cdma_wait_pushbuffer_space(host1x, cdma, needed); in host1x_cdma_push_wide()
578 cdma->slots_free = space - needed; in host1x_cdma_push_wide()
579 cdma->slots_used += needed; in host1x_cdma_push_wide()
|
| /Linux-v5.10/Documentation/devicetree/bindings/pci/ |
| D | ralink,rt3883-pci.txt | 12 - #address-cells: specifies the number of cells needed to encode an
37 - #address-cells: specifies the number of cells needed to encode an
41 - #interrupt-cells: specifies the number of cells needed to encode an
52 - #address-cells: specifies the number of cells needed to encode an
58 - #interrupt-cells: specifies the number of cells needed to encode an
|
| D | xilinx-pcie.txt | 6 - #interrupt-cells: specifies the number of cells needed to encode an
27 - #address-cells: specifies the number of cells needed to encode an
29 - #interrupt-cells: specifies the number of cells needed to encode an
|
| D | rockchip-pcie-host.txt | 6 - #interrupt-cells: specifies the number of cells needed to encode an
39 - #interrupt-cells: specifies the number of cells needed to encode an
56 - aspm-no-l0s: RC won't support ASPM L0s. This property is needed if
74 - #address-cells: specifies the number of cells needed to encode an
76 - #interrupt-cells: specifies the number of cells needed to encode an
|
| /Linux-v5.10/tools/memory-model/scripts/ |
| D | newlitmushist.sh | 57 sort -u $T/list-C-new $T/list-C-newer > $T/list-C-needed
59 scripts/runlitmushist.sh < $T/list-C-needed
|
| D | checkghlitmus.sh | 48 sort $T/list-C-already $T/list-C-result-short | uniq -u > $T/list-C-needed
51 if scripts/runlitmushist.sh < $T/list-C-needed > $T/run.stdout 2> $T/run.stderr
|
| /Linux-v5.10/drivers/ata/ |
| D | ahci_da850.c | 46 u32 pll_output = 1500000000, needed; in ahci_da850_calculate_mpy() local
57 needed = pll_output / (refclk_rate / 10); in ahci_da850_calculate_mpy()
65 switch (needed) { in ahci_da850_calculate_mpy()
|
| /Linux-v5.10/Documentation/devicetree/bindings/mtd/ |
| D | oxnas-nand.txt | 10 - clocks: phandle to the NAND gate clock if needed.
11 - resets: phandle to the NAND reset control if needed.
|
| /Linux-v5.10/Documentation/devicetree/bindings/phy/ |
| D | bcm-ns-usb2-phy.txt | 6 - reg-names: "dmu", the only needed & supported reg right now
8 - clock-names: "phy-ref-clk", the only needed & supported clock right now
|
| /Linux-v5.10/Documentation/devicetree/bindings/thermal/ |
| D | mediatek-thermal.txt | 8 is also needed.
19 - clocks, clock-names: Clocks needed for the thermal controller. required
21 "therm": Main clock needed for register access
|
| /Linux-v5.10/drivers/md/ |
| D | dm-ioctl.c | 510 size_t len, needed = 0; in list_devices() local
523 needed += align_val(offsetof(struct dm_name_list, name) + strlen(hc->name) + 1); in list_devices()
524 needed += align_val(sizeof(uint32_t)); in list_devices()
532 if (len < needed) { in list_devices()
536 param->data_size = param->data_start + needed; in list_devices()
563 BUG_ON((char *)nl - (char *)orig_nl != needed); in list_devices()
572 size_t *needed = needed_param; in list_version_get_needed() local
574 *needed += sizeof(struct dm_target_versions); in list_version_get_needed()
575 *needed += strlen(tt->name); in list_version_get_needed()
576 *needed += ALIGN_MASK; in list_version_get_needed()
[all …]
|
| /Linux-v5.10/Documentation/devicetree/bindings/iio/humidity/ |
| D | hts221.txt | 12 IRQ_TYPE_EDGE_RISING a pull-down resistor is needed to drive the line
13 when it is not active, whereas a pull-up one is needed when interrupt
|
