Searched refs:loop1 (Results 1 – 18 of 18) sorted by relevance
| /Linux-v5.10/Documentation/devicetree/bindings/sound/ |
| D | axentia,tse850-pcm5142.txt | 8 - axentia,loop1-gpios: gpio specifier that controls loop relays on channel 1.
15 loop1 relays
32 The 'loop1' gpio pin controlls two relays, which are either in loop position,
37 In the above, the 'loop1' relays are inactive, thus feeding IN1 to the mixer
88 axentia,loop1-gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
|
| /Linux-v5.10/sound/soc/atmel/ |
| D | tse850-pcm5142.c | 50 struct gpio_desc *loop1; member
84 gpiod_set_value_cansleep(tse850->loop1, val); in tse850_put_mux1()
381 tse850->loop1 = devm_gpiod_get(dev, "axentia,loop1", GPIOD_OUT_HIGH); in tse850_probe()
382 if (IS_ERR(tse850->loop1)) { in tse850_probe()
383 if (PTR_ERR(tse850->loop1) != -EPROBE_DEFER) in tse850_probe()
385 return PTR_ERR(tse850->loop1); in tse850_probe()
|
| /Linux-v5.10/arch/alpha/math-emu/ |
| D | qrnnd.S | 52 $loop1: cmplt n0,0,tmp
85 bgt cnt,$loop1
|
| /Linux-v5.10/arch/powerpc/mm/ |
| D | mem.c | 439 unsigned long loop1 = addr, loop2 = addr; in flush_dcache_icache_phys() local
462 : "+&r" (loop1), "+&r" (loop2) in flush_dcache_icache_phys()
|
| /Linux-v5.10/arch/arm/mm/ |
| D | cache-v7m.S | 202 loop1: label
213 bge loop1
|
| D | cache-v7.S | 154 loop1: label
167 bge loop1
|
| /Linux-v5.10/arch/m68k/fpsp040/ |
| D | x_snan.S | 98 loop1: label
100 dbra %d0,loop1
|
| D | gen_except.S | 291 loop1: label
293 dbra %d0,loop1
|
| /Linux-v5.10/arch/arm/boot/dts/ |
| D | at91-tse850-3.dts | 55 axentia,loop1-gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
|
| /Linux-v5.10/arch/x86/crypto/ |
| D | sha256-avx-asm.S | 394 loop1: label
413 jne loop1
|
| D | sha256-ssse3-asm.S | 404 loop1: label
427 jne loop1
|
| D | sha256-avx2-asm.S | 593 loop1: label
612 jb loop1
|
| D | sha512-avx2-asm.S | 621 loop1: label
640 jne loop1
|
| /Linux-v5.10/Documentation/translations/zh_CN/process/ |
| D | coding-style.rst | 424 while (loop1) {
|
| /Linux-v5.10/drivers/block/ |
| D | Kconfig | 182 called /dev/loop0, /dev/loop1 etc.
|
| /Linux-v5.10/Documentation/process/ |
| D | coding-style.rst | 511 while (loop1) {
|
| /Linux-v5.10/Documentation/translations/it_IT/process/ |
| D | coding-style.rst | 490 while (loop1) {
|
| /Linux-v5.10/Documentation/admin-guide/ |
| D | devices.txt | 193 1 = /dev/loop1 Second loop device
|
