Searched refs:int1 (Results 1 – 19 of 19) sorted by relevance
| /Linux-v5.10/drivers/iio/accel/ |
| D | st_accel_core.c | 161 .int1 = {
235 .int1 = {
329 .int1 = {
407 .int1 = {
469 .int1 = {
548 .int1 = {
607 .int1 = {
680 .int1 = {
753 .int1 = {
811 .int1 = {
[all …]
|
| /Linux-v5.10/arch/m68k/include/asm/ |
| D | traps.h | 238 unsigned short int1[4]; /* internal registers */ member
241 unsigned short int1; member
251 unsigned short int1; member
|
| /Linux-v5.10/drivers/iio/common/st_sensors/ |
| D | st_sensors_core.c | 271 if (!sdata->sensor_settings->drdy_irq.int1.addr && in st_sensors_set_drdy_int_pin()
282 if (!sdata->sensor_settings->drdy_irq.int1.mask) { in st_sensors_set_drdy_int_pin()
303 if (!sdata->sensor_settings->drdy_irq.int1.addr_od && in st_sensors_set_drdy_int_pin()
423 addr = sdata->sensor_settings->drdy_irq.int1.addr_od; in st_sensors_init_sensor()
424 mask = sdata->sensor_settings->drdy_irq.int1.mask_od; in st_sensors_init_sensor()
451 if (!sdata->sensor_settings->drdy_irq.int1.addr && in st_sensors_set_dataready_irq()
475 drdy_addr = sdata->sensor_settings->drdy_irq.int1.addr; in st_sensors_set_dataready_irq()
476 drdy_mask = sdata->sensor_settings->drdy_irq.int1.mask; in st_sensors_set_dataready_irq()
|
| /Linux-v5.10/arch/mips/boot/dts/loongson/ |
| D | loongson64g-package.dtsi | 33 interrupt-names = "int0", "int1";
36 <0xff000000>, /* int1 */
|
| D | loongson64c-package.dtsi | 36 interrupt-names = "int0", "int1";
39 <0x0f000000>, /* int1 */
|
| D | loongson64v_4core_virtio.dts | 35 interrupt-names = "int0", "int1";
38 <0xfffffffe>, /* int1 */
|
| /Linux-v5.10/arch/arm/boot/dts/ |
| D | stm32mp153.dtsi | 32 interrupt-names = "int0", "int1";
45 interrupt-names = "int0", "int1";
|
| D | dra76x.dtsi | 34 interrupt-names = "int0", "int1";
|
| D | imx7d.dtsi | 142 interrupt-names = "int0", "int1", "int2", "pps";
|
| D | sama5d2.dtsi | 731 interrupt-names = "int0", "int1";
1137 interrupt-names = "int0", "int1";
|
| D | imx7s.dtsi | 1192 interrupt-names = "int0", "int1", "int2", "pps";
|
| /Linux-v5.10/drivers/iio/pressure/ |
| D | st_pressure_core.c | 280 .int1 = {
403 .int1 = {
472 .int1 = {
541 .int1 = {
715 if (!pdata && (press_data->sensor_settings->drdy_irq.int1.addr || in st_press_common_probe()
|
| /Linux-v5.10/Documentation/devicetree/bindings/net/ |
| D | fsl-fec.txt | 35 3 "int0", "int1", "int2"
36 4 "int0", "int1", "int2", "pps"
38 property. Currently, only i.mx7 uses "int1" and "int2". They correspond to
|
| /Linux-v5.10/lib/raid6/ |
| D | Makefile | 4 raid6_pq-y += algos.o recov.o tables.o int1.o int2.o int4.o \
53 targets += int1.c int2.c int4.c int8.c int16.c int32.c
|
| /Linux-v5.10/lib/raid6/test/ |
| D | Makefile | 14 OBJS = int1.o int2.o int4.o int8.o int16.o int32.o recov.o algos.o tables.o
110 int1.c: int.uc ../unroll.awk
|
| /Linux-v5.10/include/linux/iio/common/ |
| D | st_sensors.h | 163 struct st_sensor_int_drdy int1; member
|
| /Linux-v5.10/Documentation/ |
| D | dontdiff | 147 int1.c
|
| /Linux-v5.10/Documentation/devicetree/bindings/pinctrl/ |
| D | marvell,armada-xp-pinctrl.txt | 51 mpp30 30 gpio, tdm(int1), sd0(clk)
|
| /Linux-v5.10/drivers/iio/magnetometer/ |
| D | st_magn_core.c | 371 .int1 = {
|
