| /Linux-v5.10/Documentation/devicetree/bindings/power/supply/ |
| D | lp8727_charger.txt | 11 AC and USB charging parameters
14 - charging-current: value of 'enum lp8727_ichg' (u8)
30 /* AC charger: 5% EOC and 500mA charging current */
34 charging-current = /bits/ 8 <4>;
37 /* USB charger: 10% EOC and 400mA charging current */
41 charging-current = /bits/ 8 <2>;
|
| D | charger-manager.txt | 22 external power is connected, or 3 for when charging. If not present,
28 - cm-fullbatt-vchkdrop-volt : voltage drop (in uV) before restarting charging
33 - cm-battery-* : threshold battery temperature for charging
34 -cold : critical cold temperature of battery for charging
36 -hot : critical hot temperature of battery for charging
38 - cm-dis/charging-max = limits of charging duration
70 /* Allow charging for 5hr */
71 cm-charging-max = <18000000>;
|
| D | twl-charger.txt | 4 to know when charging is permissible, and when there is a connection
11 use USB power for charging.
20 - ti,bb-uvolt: microvolts for charging the backup battery.
21 - ti,bb-uamp: microamps for charging the backup battery.
|
| D | qcom,coincell-charger.txt | 3 The hardware block controls charging for a coincell or capacitor that is
26 Definition: voltage (in millivolts) to apply for charging
32 Definition: defining this property disables charging
|
| D | qcom_smbb.txt | 51 Description: Battery voltage limit above which fast charging may operate;
52 Below this value linear or switch-mode auto-trickle-charging
58 Description: Battery voltage limit below which fast charging may operate;
80 will restart charging after end-of-charge; The high cutoff
86 Description: Input voltage level above which charging may operate
103 temperature range. It only allows charging when the battery
120 input voltage from external VBUS for charging. In the
|
| D | bq25890.txt | 14 - ti,battery-regulation-voltage: integer, maximum charging voltage (in uV);
15 - ti,charge-current: integer, maximum charging current (in uA);
20 - ti,minimum-sys-voltage: integer, when battery is charging and it is below
38 - ti,ibatcomp-clamp-microvolt: integer, maximum charging voltage adjustment due
|
| D | max8925_battery.txt | 6 - topoff-threshold: set charging current in topoff mode
7 - fast-charge: set charging current in fast mode
|
| D | tps65090.txt | 7 -ti,enable-low-current-chrg: Enables charging when a low current is detected
8 while the default logic is to stop charging.
|
| D | ti,bq24735.txt | 15 - ti,charge-current : Used to control and set the charging current. This value
19 - ti,charge-voltage : Used to control and set the charging voltage. This value
28 and that the host should not attempt to enable/disable charging or set the
|
| D | bq2415x.txt | 23 - ti,battery-regulation-voltage: integer, maximum charging voltage in mV.
24 - ti,charge-current: integer, maximum charging current in mA.
|
| D | bq24257.txt | 11 - ti,battery-regulation-voltage: integer, maximum charging voltage in uV.
12 - ti,charge-current: integer, maximum charging current in uA.
|
| /Linux-v5.10/Documentation/devicetree/bindings/rtc/ |
| D | rtc-palmas.txt | 14 battery is chargeable or not. If charging battery then driver can
15 enable the charging.
16 - ti,backup-battery-charge-high-current: Enable high current charging in
17 backup battery. Device supports the < 100uA and > 100uA charging.
|
| /Linux-v5.10/Documentation/ABI/testing/ |
| D | sysfs-class-power | 61 used for discharging batteries, positive values for charging
101 used for discharging batteries, positive values for charging
136 This is normally used for the charging scenario where
139 user that the temperature is critically high, and charging has
161 This is normally used for the charging scenario where user-space
164 temperature level is high, and charging current has been
178 charging.
195 charging.
212 battery, during charging.
335 Maximum allowable charging current. Used for charge rate
[all …]
|
| D | sysfs-class-power-twl4030 | 4 Writing to this can disable charging.
25 Writing to this can disable charging.
|
| D | sysfs-class-power-mp2629 | 5 Represents a battery impedance compensation to accelerate charging.
|
| /Linux-v5.10/drivers/power/supply/ |
| D | sc2731_charger.c | 62 bool charging; member
211 if (!info->charging) { in sc2731_charger_usb_set_property()
250 if (info->charging) in sc2731_charger_usb_get_property()
257 if (!info->charging) { in sc2731_charger_usb_get_property()
269 if (!info->charging) { in sc2731_charger_usb_get_property()
331 if (info->limit > 0 && !info->charging) { in sc2731_charger_work()
345 info->charging = true; in sc2731_charger_work()
346 } else if (!info->limit && info->charging) { in sc2731_charger_work()
348 info->charging = false; in sc2731_charger_work()
|
| D | bq24735-charger.c | 55 bool charging; member
222 if (charger->charging && bq24735_charger_is_present(charger)) in bq24735_update()
294 charger->charging = true; in bq24735_charger_set_property()
303 charger->charging = false; in bq24735_charger_set_property()
366 charger->charging = true; in bq24735_charger_probe()
|
| /Linux-v5.10/arch/sh/boards/mach-hp6xx/ |
| D | hp6xx_apm.c | 32 int battery, backup, charging, percentage; in hp6x0_apm_get_power_status() local
37 charging = adc_single(ADC_CHANNEL_CHARGE); in hp6x0_apm_get_power_status()
58 } else if (charging < 8) { in hp6x0_apm_get_power_status()
|
| /Linux-v5.10/drivers/macintosh/ |
| D | apm_emu.c | 24 char charging = 0; in pmu_apm_get_power_status() local
53 charging++; in pmu_apm_get_power_status()
67 if (charging > 0) { in pmu_apm_get_power_status()
|
| /Linux-v5.10/drivers/mfd/ |
| D | tps65010.c | 65 unsigned charging:1; member
206 seq_printf(s, "%scharging\n\n", tps->charging ? "" : "(not) "); in dbg_show()
352 unsigned charging = 0; in tps65010_interrupt() local
370 charging = 1; in tps65010_interrupt()
372 charging = 1; in tps65010_interrupt()
374 if (charging != tps->charging) { in tps65010_interrupt()
375 tps->charging = charging; in tps65010_interrupt()
377 DRIVER_NAME, charging ? "" : in tps65010_interrupt()
386 if ((tps->model != TPS65013 || !tps->charging) in tps65010_interrupt()
|
| /Linux-v5.10/Documentation/hwmon/ |
| D | twl4030-madc-hwmon.rst | 48 degree Celsius. The Battery charging current channel represents
49 battery charging current in mA.
|
| /Linux-v5.10/include/linux/power/ |
| D | twl4030_madc_battery.h | 24 struct twl4030_madc_bat_calibration *charging; member
|
| /Linux-v5.10/Documentation/power/ |
| D | power_supply_class.rst | 25 typically expected feedback of battery charging/fully charged status and
83 this attribute represents operating status (charging, full,
167 the current drawn from a charging source.
170 the voltage limit from a charging source.
173 the power limit from a charging source.
214 (i.e. while battery is charging)
|
| D | charger-manager.rst | 38 consumption and slow down charging process. Or even, such peak power
39 consumption can stop chargers in the middle of charging
41 only affects the charging time, but the lifespan of the battery.
53 restarts charging. This check is also performed while suspended by
178 This callback returns 0 if the temperature is safe for charging,
203 a) charger-on/off b) external-power-in/out c) battery-in/out (while charging)
|
| /Linux-v5.10/Documentation/devicetree/bindings/pwm/ |
| D | ti,twl-pwmled.txt | 5 On TWL6030 series: LED PWM (mainly used as charging indicator LED)
|
