Searched refs:changing (Results 1 – 25 of 254) sorted by relevance
1234567891011
| /Linux-v5.10/Documentation/userspace-api/media/v4l/ |
| D | app-pri.rst | 12 applications from changing video controls or switching the current TV
28 Ioctls changing driver properties, such as
|
| /Linux-v5.10/Documentation/devicetree/bindings/regulator/ |
| D | max8997-regulator.txt | 14 units for buck1 when changing voltage using gpio dvs. Refer to [1] below
18 units for buck2 when changing voltage using gpio dvs. Refer to [1] below
22 units for buck5 when changing voltage using gpio dvs. Refer to [1] below
44 multiple bucks, changing the voltage value of one of the bucks may affect
|
| D | samsung,s5m8767.txt | 17 units for buck2 when changing voltage using gpio dvs. Refer to [1] below
21 units for buck3 when changing voltage using gpio dvs. Refer to [1] below
25 units for buck4 when changing voltage using gpio dvs. Refer to [1] below
|
| D | max77802.txt | 57 changing their mode during normal operation are: LDOs 1, 3, 20 and 21.
67 support changing their mode to Low Power Mode during suspend. These regulators
|
| D | qcom,rpmh-regulator.txt | 6 Coordinator (RSC) using command packets. The VRM allows changing three
8 mode. The XOB allows changing only a single parameter for a given regulator:
|
| /Linux-v5.10/Documentation/driver-api/thermal/ |
| D | exynos_thermal_emulation.rst | 28 delay of changing temperature. However, this node only uses same delay
31 Exynos emulation mode requires synchronous of value changing and
|
| /Linux-v5.10/Documentation/userspace-api/media/rc/ |
| D | lirc-get-features.rst | 81 The driver supports changing the modulation frequency via
88 The driver supports changing the duty cycle using
95 The driver supports changing the active transmitter(s) using
|
| D | rc-table-change.rst | 10 /dev/input/event device, to allow changing the default keymapping.
|
| /Linux-v5.10/security/integrity/evm/ |
| D | Kconfig | 26 WARNING: changing the HMAC calculation method or adding
43 WARNING: changing the HMAC calculation method or adding
|
| /Linux-v5.10/Documentation/ABI/testing/ |
| D | sysfs-class-leds-gt683r | 6 Set the mode of LEDs. You should notice that changing the mode
|
| D | sysfs-bus-iio-frequency-adf4371 | 23 all the other channels, since it involves changing the VCO
|
| D | sysfs-bus-iio-isl29501 | 25 measurements due to changing temperature and ambient
|
| /Linux-v5.10/Documentation/networking/device_drivers/fddi/ |
| D | defza.rst | 40 doesn't support changing them individually.
50 5. MAC address change. The card does not support changing the Media
|
| /Linux-v5.10/Documentation/i2c/busses/ |
| D | i2c-ismt.rst | 18 Allows changing of the bus speed. Normally, the bus speed is set by the BIOS
|
| /Linux-v5.10/Documentation/cpu-freq/ |
| D | index.rst | 23 There is a CPU frequency changing CVS commit and general list where
|
| /Linux-v5.10/drivers/memory/samsung/ |
| D | Kconfig | 19 DMC and DRAM. It also supports changing timings of DRAM running with
|
| /Linux-v5.10/Documentation/networking/ |
| D | ip_dynaddr.rst | 8 dynamically changing packet source address (and socket's if local procs).
|
| /Linux-v5.10/Documentation/arm/samsung-s3c24xx/ |
| D | eb2410itx.rst | 50 changing speed of devices, PIO Mode 4 capable drives should be used.
|
| /Linux-v5.10/Documentation/RCU/ |
| D | rcuref.rst | 47 If this list/array is made lock free using RCU as in changing the
48 write_lock() in add() and delete() to spin_lock() and changing read_lock()
|
| /Linux-v5.10/drivers/ntb/hw/idt/ |
| D | Kconfig | 12 by BIOS using slave-SMBus interface changing corresponding registers
|
| /Linux-v5.10/Documentation/features/sched/membarrier-sync-core/ |
| D | arch-support.txt | 25 # after changing the current mm, and deal with the special case of kthread ->
|
| /Linux-v5.10/arch/arm/boot/dts/ |
| D | kirkwood-openrd.dtsi | 84 * When changing this line make sure the newly
|
| /Linux-v5.10/Documentation/fb/ |
| D | cirrusfb.rst | 48 * Hint for AXP: Use -accel false -vyres -1 when changing resolution
|
| /Linux-v5.10/arch/powerpc/boot/dts/ |
| D | sbc8548-altflash.dts | 6 * Requires switching JP12 jumpers and changing SW2.8 setting.
|
| /Linux-v5.10/Documentation/devicetree/bindings/mtd/ |
| D | gpio-control-nand.txt | 24 the GPIO's and the NAND flash data bus. If present, then after changing
|
1234567891011
