| /Linux-v5.10/Documentation/devicetree/bindings/sound/ |
| D | nau8824.txt | 30 …eshold for each button. Array that contains up to 8 buttons configuration. SAR value is calculated…
31 SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R)
47 - nuvoton,sar-compare-time: SAR compare time
53 - nuvoton,sar-sampling-time: SAR sampling time
|
| D | nau8825.txt | 34 …eshold for each button. Array that contains up to 8 buttons configuration. SAR value is calculated…
35 SAR = 255 * MICBIAS / SAR_VOLTAGE * R / (2000 + R)
51 - nuvoton,sar-compare-time: SAR compare time
57 - nuvoton,sar-sampling-time: SAR sampling time
|
| /Linux-v5.10/drivers/dma/ |
| D | txx9dmac.h | 72 u64 SAR; /* Source Address Register */ member
82 u32 SAR; member
206 u64 SAR; member
212 u32 SAR; member
|
| D | txx9dmac.c | 290 channel64_readq(dc, SAR), in txx9dmac_dump_regs()
302 channel32_readl(dc, SAR), in txx9dmac_dump_regs()
316 channel_writeq(dc, SAR, 0); in txx9dmac_reset_chan()
320 channel_writel(dc, SAR, 0); in txx9dmac_reset_chan()
474 (u64)desc->CHAR, desc->SAR, desc->DAR, desc->CNTR); in txx9dmac_dump_desc()
479 (u64)desc->CHAR, desc->SAR, desc->DAR, desc->CNTR, in txx9dmac_dump_desc()
487 d->CHAR, d->SAR, d->DAR, d->CNTR); in txx9dmac_dump_desc()
492 d->CHAR, d->SAR, d->DAR, d->CNTR, in txx9dmac_dump_desc()
755 desc->hwdesc.SAR = src + offset; in txx9dmac_prep_dma_memcpy()
761 desc->hwdesc32.SAR = src + offset; in txx9dmac_prep_dma_memcpy()
[all …]
|
| D | idma64.c | 94 channel_writeq(idma64c, SAR, 0); in idma64_chan_start()
|
| D | pl330.c | 339 SAR = 0, enumerator
726 dst == SAR ? "SAR" : (dst == DAR ? "DAR" : "CCR"), val); in _emit_MOV()
1394 off += _emit_MOV(dry_run, &buf[off], SAR, x->src_addr); in _setup_xfer()
|
| /Linux-v5.10/arch/sh/include/asm/ |
| D | dma-register.h | 14 #define SAR 0x00 /* Source Address Register */ macro
|
| /Linux-v5.10/drivers/i2c/busses/ |
| D | i2c-rcar.c | 70 #define SAR (1 << 0) /* slave addr received */ macro
576 if (ssr_filtered & SAR) { in rcar_i2c_slave_irq()
581 rcar_i2c_write(priv, ICSIER, SDE | SSR | SAR); in rcar_i2c_slave_irq()
585 rcar_i2c_write(priv, ICSIER, SDR | SSR | SAR); in rcar_i2c_slave_irq()
589 rcar_i2c_write(priv, ICSSR, ~(SAR | SSR) & 0xff); in rcar_i2c_slave_irq()
596 rcar_i2c_write(priv, ICSIER, SAR); in rcar_i2c_slave_irq()
854 rcar_i2c_write(priv, ICSIER, SAR); in rcar_reg_slave()
|
| /Linux-v5.10/drivers/net/wireless/ath/ath9k/ |
| D | Kconfig | 90 TX99 support enables Specific Absorption Rate (SAR) testing.
91 SAR is the unit of measurement for the amount of radio frequency(RF)
93 limits used are expressed in the terms of SAR, which is a measure
98 governmental SAR regulations.
|
| /Linux-v5.10/Documentation/devicetree/bindings/clock/ |
| D | mvebu-core-clock.txt | 4 reading the Sample-At-Reset (SAR) register. The core clock consumer should
67 - reg : shall be the register address of the Sample-At-Reset (SAR) register
|
| /Linux-v5.10/Documentation/hwmon/ |
| D | adm1266.rst | 20 integrated 12 bit SAR ADC, accessed using a PMBus interface.
|
| /Linux-v5.10/drivers/dma/sh/ |
| D | shdmac.c | 38 #define SAR 0x00 /* Source Address Register */ macro
217 sh_dmae_writel(sh_chan, hw->sar, SAR); in dmae_set_reg()
460 u32 sar_buf = sh_dmae_readl(sh_chan, SAR); in sh_dmae_desc_completed()
|
| /Linux-v5.10/arch/xtensa/kernel/ |
| D | coprocessor.S | 174 ssl a3 # SAR: 32 - coprocessor_number
|
| D | entry.S | 1269 ssr a0 # save in SAR for later.
1531 rsr a3, sar # WB is still in SAR
|
| /Linux-v5.10/Documentation/devicetree/bindings/mfd/ |
| D | rohm,bd70528-pmic.txt | 8 dual-input power path, 10 bit SAR ADC for battery temperature monitor and
|
| /Linux-v5.10/arch/sh/drivers/dma/ |
| D | dma-sh.c | 219 __raw_writel(chan->sar, (dma_base_addr(chan->chan) + SAR)); in sh_dmac_xfer_dma()
|
| /Linux-v5.10/drivers/dma/dw/ |
| D | regs.h | 40 DW_REG(SAR); /* Source Address Register */
|
| D | core.c | 134 channel_readl(dwc, SAR), in dwc_dump_chan_regs()
163 channel_writel(dwc, SAR, lli_read(desc, sar)); in dwc_do_single_block()
|
| /Linux-v5.10/arch/arm/mach-omap2/ |
| D | sleep44xx.S | 148 ldreq r0, [r8, #L2X0_SAVE_OFFSET0] @ Retrieve L2 state from SAR
|
| /Linux-v5.10/Documentation/parisc/ |
| D | registers.rst | 19 CR11 as specified by ABI (SAR)
|
| /Linux-v5.10/arch/arm/boot/dts/ |
| D | armada-xp-synology-ds414.dts | 72 * pin being sampled at reset (bit 0 of SAR).
|
| D | armada-385-clearfog-gtr.dtsi | 50 47 - Control isolation of boot sensitive SAR signals
|
| /Linux-v5.10/drivers/iio/adc/ |
| D | Kconfig | 730 tristate "Amlogic Meson SAR ADC driver"
735 Say yes here to build support for the SAR ADC found in Amlogic Meson
|
| /Linux-v5.10/arch/x86/lib/ |
| D | x86-opcode-map.txt | 916 7: SAR
|
| /Linux-v5.10/tools/arch/x86/lib/ |
| D | x86-opcode-map.txt | 916 7: SAR
|
