1 /* SPDX-License-Identifier: GPL-2.0-only */ 2 /* 3 * Copyright (C) STMicroelectronics 2009 4 * Copyright (C) ST-Ericsson SA 2010 5 * 6 * Author: Kumar Sanghvi <kumar.sanghvi@stericsson.com> 7 * 8 * PRCMU f/w APIs 9 */ 10 #ifndef __MFD_DB8500_PRCMU_H 11 #define __MFD_DB8500_PRCMU_H 12 13 #include <linux/interrupt.h> 14 #include <linux/bitops.h> 15 16 /* 17 * Registers 18 */ 19 #define DB8500_PRCM_LINE_VALUE 0x170 20 #define DB8500_PRCM_LINE_VALUE_HSI_CAWAKE0 BIT(3) 21 22 #define DB8500_PRCM_DSI_SW_RESET 0x324 23 #define DB8500_PRCM_DSI_SW_RESET_DSI0_SW_RESETN BIT(0) 24 #define DB8500_PRCM_DSI_SW_RESET_DSI1_SW_RESETN BIT(1) 25 #define DB8500_PRCM_DSI_SW_RESET_DSI2_SW_RESETN BIT(2) 26 27 /* This portion previously known as <mach/prcmu-fw-defs_v1.h> */ 28 29 /** 30 * enum state - ON/OFF state definition 31 * @OFF: State is ON 32 * @ON: State is OFF 33 * 34 */ 35 enum state { 36 OFF = 0x0, 37 ON = 0x1, 38 }; 39 40 /** 41 * enum ret_state - general purpose On/Off/Retention states 42 * 43 */ 44 enum ret_state { 45 OFFST = 0, 46 ONST = 1, 47 RETST = 2 48 }; 49 50 /** 51 * enum clk_arm - ARM Cortex A9 clock schemes 52 * @A9_OFF: 53 * @A9_BOOT: 54 * @A9_OPPT1: 55 * @A9_OPPT2: 56 * @A9_EXTCLK: 57 */ 58 enum clk_arm { 59 A9_OFF, 60 A9_BOOT, 61 A9_OPPT1, 62 A9_OPPT2, 63 A9_EXTCLK 64 }; 65 66 /** 67 * enum clk_gen - GEN#0/GEN#1 clock schemes 68 * @GEN_OFF: 69 * @GEN_BOOT: 70 * @GEN_OPPT1: 71 */ 72 enum clk_gen { 73 GEN_OFF, 74 GEN_BOOT, 75 GEN_OPPT1, 76 }; 77 78 /* some information between arm and xp70 */ 79 80 /** 81 * enum romcode_write - Romcode message written by A9 AND read by XP70 82 * @RDY_2_DS: Value set when ApDeepSleep state can be executed by XP70 83 * @RDY_2_XP70_RST: Value set when 0x0F has been successfully polled by the 84 * romcode. The xp70 will go into self-reset 85 */ 86 enum romcode_write { 87 RDY_2_DS = 0x09, 88 RDY_2_XP70_RST = 0x10 89 }; 90 91 /** 92 * enum romcode_read - Romcode message written by XP70 and read by A9 93 * @INIT: Init value when romcode field is not used 94 * @FS_2_DS: Value set when power state is going from ApExecute to 95 * ApDeepSleep 96 * @END_DS: Value set when ApDeepSleep power state is reached coming from 97 * ApExecute state 98 * @DS_TO_FS: Value set when power state is going from ApDeepSleep to 99 * ApExecute 100 * @END_FS: Value set when ApExecute power state is reached coming from 101 * ApDeepSleep state 102 * @SWR: Value set when power state is going to ApReset 103 * @END_SWR: Value set when the xp70 finished executing ApReset actions and 104 * waits for romcode acknowledgment to go to self-reset 105 */ 106 enum romcode_read { 107 INIT = 0x00, 108 FS_2_DS = 0x0A, 109 END_DS = 0x0B, 110 DS_TO_FS = 0x0C, 111 END_FS = 0x0D, 112 SWR = 0x0E, 113 END_SWR = 0x0F 114 }; 115 116 /** 117 * enum ap_pwrst - current power states defined in PRCMU firmware 118 * @NO_PWRST: Current power state init 119 * @AP_BOOT: Current power state is apBoot 120 * @AP_EXECUTE: Current power state is apExecute 121 * @AP_DEEP_SLEEP: Current power state is apDeepSleep 122 * @AP_SLEEP: Current power state is apSleep 123 * @AP_IDLE: Current power state is apIdle 124 * @AP_RESET: Current power state is apReset 125 */ 126 enum ap_pwrst { 127 NO_PWRST = 0x00, 128 AP_BOOT = 0x01, 129 AP_EXECUTE = 0x02, 130 AP_DEEP_SLEEP = 0x03, 131 AP_SLEEP = 0x04, 132 AP_IDLE = 0x05, 133 AP_RESET = 0x06 134 }; 135 136 /** 137 * enum ap_pwrst_trans - Transition states defined in PRCMU firmware 138 * @NO_TRANSITION: No power state transition 139 * @APEXECUTE_TO_APSLEEP: Power state transition from ApExecute to ApSleep 140 * @APIDLE_TO_APSLEEP: Power state transition from ApIdle to ApSleep 141 * @APBOOT_TO_APEXECUTE: Power state transition from ApBoot to ApExecute 142 * @APEXECUTE_TO_APDEEPSLEEP: Power state transition from ApExecute to 143 * ApDeepSleep 144 * @APEXECUTE_TO_APIDLE: Power state transition from ApExecute to ApIdle 145 */ 146 enum ap_pwrst_trans { 147 PRCMU_AP_NO_CHANGE = 0x00, 148 APEXECUTE_TO_APSLEEP = 0x01, 149 APIDLE_TO_APSLEEP = 0x02, /* To be removed */ 150 PRCMU_AP_SLEEP = 0x01, 151 APBOOT_TO_APEXECUTE = 0x03, 152 APEXECUTE_TO_APDEEPSLEEP = 0x04, /* To be removed */ 153 PRCMU_AP_DEEP_SLEEP = 0x04, 154 APEXECUTE_TO_APIDLE = 0x05, /* To be removed */ 155 PRCMU_AP_IDLE = 0x05, 156 PRCMU_AP_DEEP_IDLE = 0x07, 157 }; 158 159 /** 160 * enum hw_acc_state - State definition for hardware accelerator 161 * @HW_NO_CHANGE: The hardware accelerator state must remain unchanged 162 * @HW_OFF: The hardware accelerator must be switched off 163 * @HW_OFF_RAMRET: The hardware accelerator must be switched off with its 164 * internal RAM in retention 165 * @HW_ON: The hwa hardware accelerator hwa must be switched on 166 * 167 * NOTE! Deprecated, to be removed when all users switched over to use the 168 * regulator API. 169 */ 170 enum hw_acc_state { 171 HW_NO_CHANGE = 0x00, 172 HW_OFF = 0x01, 173 HW_OFF_RAMRET = 0x02, 174 HW_ON = 0x04 175 }; 176 177 /** 178 * enum mbox_2_arm_stat - Status messages definition for mbox_arm 179 * @BOOT_TO_EXECUTEOK: The apBoot to apExecute state transition has been 180 * completed 181 * @DEEPSLEEPOK: The apExecute to apDeepSleep state transition has been 182 * completed 183 * @SLEEPOK: The apExecute to apSleep state transition has been completed 184 * @IDLEOK: The apExecute to apIdle state transition has been completed 185 * @SOFTRESETOK: The A9 watchdog/ SoftReset state has been completed 186 * @SOFTRESETGO : The A9 watchdog/SoftReset state is on going 187 * @BOOT_TO_EXECUTE: The apBoot to apExecute state transition is on going 188 * @EXECUTE_TO_DEEPSLEEP: The apExecute to apDeepSleep state transition is on 189 * going 190 * @DEEPSLEEP_TO_EXECUTE: The apDeepSleep to apExecute state transition is on 191 * going 192 * @DEEPSLEEP_TO_EXECUTEOK: The apDeepSleep to apExecute state transition has 193 * been completed 194 * @EXECUTE_TO_SLEEP: The apExecute to apSleep state transition is on going 195 * @SLEEP_TO_EXECUTE: The apSleep to apExecute state transition is on going 196 * @SLEEP_TO_EXECUTEOK: The apSleep to apExecute state transition has been 197 * completed 198 * @EXECUTE_TO_IDLE: The apExecute to apIdle state transition is on going 199 * @IDLE_TO_EXECUTE: The apIdle to apExecute state transition is on going 200 * @IDLE_TO_EXECUTEOK: The apIdle to apExecute state transition has been 201 * completed 202 * @INIT_STATUS: Status init 203 */ 204 enum ap_pwrsttr_status { 205 BOOT_TO_EXECUTEOK = 0xFF, 206 DEEPSLEEPOK = 0xFE, 207 SLEEPOK = 0xFD, 208 IDLEOK = 0xFC, 209 SOFTRESETOK = 0xFB, 210 SOFTRESETGO = 0xFA, 211 BOOT_TO_EXECUTE = 0xF9, 212 EXECUTE_TO_DEEPSLEEP = 0xF8, 213 DEEPSLEEP_TO_EXECUTE = 0xF7, 214 DEEPSLEEP_TO_EXECUTEOK = 0xF6, 215 EXECUTE_TO_SLEEP = 0xF5, 216 SLEEP_TO_EXECUTE = 0xF4, 217 SLEEP_TO_EXECUTEOK = 0xF3, 218 EXECUTE_TO_IDLE = 0xF2, 219 IDLE_TO_EXECUTE = 0xF1, 220 IDLE_TO_EXECUTEOK = 0xF0, 221 RDYTODS_RETURNTOEXE = 0xEF, 222 NORDYTODS_RETURNTOEXE = 0xEE, 223 EXETOSLEEP_RETURNTOEXE = 0xED, 224 EXETOIDLE_RETURNTOEXE = 0xEC, 225 INIT_STATUS = 0xEB, 226 227 /*error messages */ 228 INITERROR = 0x00, 229 PLLARMLOCKP_ER = 0x01, 230 PLLDDRLOCKP_ER = 0x02, 231 PLLSOCLOCKP_ER = 0x03, 232 PLLSOCK1LOCKP_ER = 0x04, 233 ARMWFI_ER = 0x05, 234 SYSCLKOK_ER = 0x06, 235 I2C_NACK_DATA_ER = 0x07, 236 BOOT_ER = 0x08, 237 I2C_STATUS_ALWAYS_1 = 0x0A, 238 I2C_NACK_REG_ADDR_ER = 0x0B, 239 I2C_NACK_DATA0123_ER = 0x1B, 240 I2C_NACK_ADDR_ER = 0x1F, 241 CURAPPWRSTISNOT_BOOT = 0x20, 242 CURAPPWRSTISNOT_EXECUTE = 0x21, 243 CURAPPWRSTISNOT_SLEEPMODE = 0x22, 244 CURAPPWRSTISNOT_CORRECTFORIT10 = 0x23, 245 FIFO4500WUISNOT_WUPEVENT = 0x24, 246 PLL32KLOCKP_ER = 0x29, 247 DDRDEEPSLEEPOK_ER = 0x2A, 248 ROMCODEREADY_ER = 0x50, 249 WUPBEFOREDS = 0x51, 250 DDRCONFIG_ER = 0x52, 251 WUPBEFORESLEEP = 0x53, 252 WUPBEFOREIDLE = 0x54 253 }; /* earlier called as mbox_2_arm_stat */ 254 255 /** 256 * enum dvfs_stat - DVFS status messages definition 257 * @DVFS_GO: A state transition DVFS is on going 258 * @DVFS_ARM100OPPOK: The state transition DVFS has been completed for 100OPP 259 * @DVFS_ARM50OPPOK: The state transition DVFS has been completed for 50OPP 260 * @DVFS_ARMEXTCLKOK: The state transition DVFS has been completed for EXTCLK 261 * @DVFS_NOCHGTCLKOK: The state transition DVFS has been completed for 262 * NOCHGCLK 263 * @DVFS_INITSTATUS: Value init 264 */ 265 enum dvfs_stat { 266 DVFS_GO = 0xFF, 267 DVFS_ARM100OPPOK = 0xFE, 268 DVFS_ARM50OPPOK = 0xFD, 269 DVFS_ARMEXTCLKOK = 0xFC, 270 DVFS_NOCHGTCLKOK = 0xFB, 271 DVFS_INITSTATUS = 0x00 272 }; 273 274 /** 275 * enum sva_mmdsp_stat - SVA MMDSP status messages 276 * @SVA_MMDSP_GO: SVAMMDSP interrupt has happened 277 * @SVA_MMDSP_INIT: Status init 278 */ 279 enum sva_mmdsp_stat { 280 SVA_MMDSP_GO = 0xFF, 281 SVA_MMDSP_INIT = 0x00 282 }; 283 284 /** 285 * enum sia_mmdsp_stat - SIA MMDSP status messages 286 * @SIA_MMDSP_GO: SIAMMDSP interrupt has happened 287 * @SIA_MMDSP_INIT: Status init 288 */ 289 enum sia_mmdsp_stat { 290 SIA_MMDSP_GO = 0xFF, 291 SIA_MMDSP_INIT = 0x00 292 }; 293 294 /** 295 * enum mbox_to_arm_err - Error messages definition 296 * @INIT_ERR: Init value 297 * @PLLARMLOCKP_ERR: PLLARM has not been correctly locked in given time 298 * @PLLDDRLOCKP_ERR: PLLDDR has not been correctly locked in the given time 299 * @PLLSOC0LOCKP_ERR: PLLSOC0 has not been correctly locked in the given time 300 * @PLLSOC1LOCKP_ERR: PLLSOC1 has not been correctly locked in the given time 301 * @ARMWFI_ERR: The ARM WFI has not been correctly executed in the given time 302 * @SYSCLKOK_ERR: The SYSCLK is not available in the given time 303 * @BOOT_ERR: Romcode has not validated the XP70 self reset in the given time 304 * @ROMCODESAVECONTEXT: The Romcode didn.t correctly save it secure context 305 * @VARMHIGHSPEEDVALTO_ERR: The ARM high speed supply value transfered 306 * through I2C has not been correctly executed in the given time 307 * @VARMHIGHSPEEDACCESS_ERR: The command value of VarmHighSpeedVal transfered 308 * through I2C has not been correctly executed in the given time 309 * @VARMLOWSPEEDVALTO_ERR:The ARM low speed supply value transfered through 310 * I2C has not been correctly executed in the given time 311 * @VARMLOWSPEEDACCESS_ERR: The command value of VarmLowSpeedVal transfered 312 * through I2C has not been correctly executed in the given time 313 * @VARMRETENTIONVALTO_ERR: The ARM retention supply value transfered through 314 * I2C has not been correctly executed in the given time 315 * @VARMRETENTIONACCESS_ERR: The command value of VarmRetentionVal transfered 316 * through I2C has not been correctly executed in the given time 317 * @VAPEHIGHSPEEDVALTO_ERR: The APE highspeed supply value transfered through 318 * I2C has not been correctly executed in the given time 319 * @VSAFEHPVALTO_ERR: The SAFE high power supply value transfered through I2C 320 * has not been correctly executed in the given time 321 * @VMODSEL1VALTO_ERR: The MODEM sel1 supply value transfered through I2C has 322 * not been correctly executed in the given time 323 * @VMODSEL2VALTO_ERR: The MODEM sel2 supply value transfered through I2C has 324 * not been correctly executed in the given time 325 * @VARMOFFACCESS_ERR: The command value of Varm ON/OFF transfered through 326 * I2C has not been correctly executed in the given time 327 * @VAPEOFFACCESS_ERR: The command value of Vape ON/OFF transfered through 328 * I2C has not been correctly executed in the given time 329 * @VARMRETACCES_ERR: The command value of Varm retention ON/OFF transfered 330 * through I2C has not been correctly executed in the given time 331 * @CURAPPWRSTISNOTBOOT:Generated when Arm want to do power state transition 332 * ApBoot to ApExecute but the power current state is not Apboot 333 * @CURAPPWRSTISNOTEXECUTE: Generated when Arm want to do power state 334 * transition from ApExecute to others power state but the 335 * power current state is not ApExecute 336 * @CURAPPWRSTISNOTSLEEPMODE: Generated when wake up events are transmitted 337 * but the power current state is not ApDeepSleep/ApSleep/ApIdle 338 * @CURAPPWRSTISNOTCORRECTDBG: Generated when wake up events are transmitted 339 * but the power current state is not correct 340 * @ARMREGU1VALTO_ERR:The ArmRegu1 value transferred through I2C has not 341 * been correctly executed in the given time 342 * @ARMREGU2VALTO_ERR: The ArmRegu2 value transferred through I2C has not 343 * been correctly executed in the given time 344 * @VAPEREGUVALTO_ERR: The VApeRegu value transfered through I2C has not 345 * been correctly executed in the given time 346 * @VSMPS3REGUVALTO_ERR: The VSmps3Regu value transfered through I2C has not 347 * been correctly executed in the given time 348 * @VMODREGUVALTO_ERR: The VModemRegu value transfered through I2C has not 349 * been correctly executed in the given time 350 */ 351 enum mbox_to_arm_err { 352 INIT_ERR = 0x00, 353 PLLARMLOCKP_ERR = 0x01, 354 PLLDDRLOCKP_ERR = 0x02, 355 PLLSOC0LOCKP_ERR = 0x03, 356 PLLSOC1LOCKP_ERR = 0x04, 357 ARMWFI_ERR = 0x05, 358 SYSCLKOK_ERR = 0x06, 359 BOOT_ERR = 0x07, 360 ROMCODESAVECONTEXT = 0x08, 361 VARMHIGHSPEEDVALTO_ERR = 0x10, 362 VARMHIGHSPEEDACCESS_ERR = 0x11, 363 VARMLOWSPEEDVALTO_ERR = 0x12, 364 VARMLOWSPEEDACCESS_ERR = 0x13, 365 VARMRETENTIONVALTO_ERR = 0x14, 366 VARMRETENTIONACCESS_ERR = 0x15, 367 VAPEHIGHSPEEDVALTO_ERR = 0x16, 368 VSAFEHPVALTO_ERR = 0x17, 369 VMODSEL1VALTO_ERR = 0x18, 370 VMODSEL2VALTO_ERR = 0x19, 371 VARMOFFACCESS_ERR = 0x1A, 372 VAPEOFFACCESS_ERR = 0x1B, 373 VARMRETACCES_ERR = 0x1C, 374 CURAPPWRSTISNOTBOOT = 0x20, 375 CURAPPWRSTISNOTEXECUTE = 0x21, 376 CURAPPWRSTISNOTSLEEPMODE = 0x22, 377 CURAPPWRSTISNOTCORRECTDBG = 0x23, 378 ARMREGU1VALTO_ERR = 0x24, 379 ARMREGU2VALTO_ERR = 0x25, 380 VAPEREGUVALTO_ERR = 0x26, 381 VSMPS3REGUVALTO_ERR = 0x27, 382 VMODREGUVALTO_ERR = 0x28 383 }; 384 385 enum hw_acc { 386 SVAMMDSP = 0, 387 SVAPIPE = 1, 388 SIAMMDSP = 2, 389 SIAPIPE = 3, 390 SGA = 4, 391 B2R2MCDE = 5, 392 ESRAM12 = 6, 393 ESRAM34 = 7, 394 }; 395 396 enum cs_pwrmgt { 397 PWRDNCS0 = 0, 398 WKUPCS0 = 1, 399 PWRDNCS1 = 2, 400 WKUPCS1 = 3 401 }; 402 403 /* Defs related to autonomous power management */ 404 405 /** 406 * enum sia_sva_pwr_policy - Power policy 407 * @NO_CHGT: No change 408 * @DSPOFF_HWPOFF: 409 * @DSPOFFRAMRET_HWPOFF: 410 * @DSPCLKOFF_HWPOFF: 411 * @DSPCLKOFF_HWPCLKOFF: 412 * 413 */ 414 enum sia_sva_pwr_policy { 415 NO_CHGT = 0x0, 416 DSPOFF_HWPOFF = 0x1, 417 DSPOFFRAMRET_HWPOFF = 0x2, 418 DSPCLKOFF_HWPOFF = 0x3, 419 DSPCLKOFF_HWPCLKOFF = 0x4, 420 }; 421 422 /** 423 * enum auto_enable - Auto Power enable 424 * @AUTO_OFF: 425 * @AUTO_ON: 426 * 427 */ 428 enum auto_enable { 429 AUTO_OFF = 0x0, 430 AUTO_ON = 0x1, 431 }; 432 433 /* End of file previously known as prcmu-fw-defs_v1.h */ 434 435 /** 436 * enum prcmu_power_status - results from set_power_state 437 * @PRCMU_SLEEP_OK: Sleep went ok 438 * @PRCMU_DEEP_SLEEP_OK: DeepSleep went ok 439 * @PRCMU_IDLE_OK: Idle went ok 440 * @PRCMU_DEEPIDLE_OK: DeepIdle went ok 441 * @PRCMU_PRCMU2ARMPENDINGIT_ER: Pending interrupt detected 442 * @PRCMU_ARMPENDINGIT_ER: Pending interrupt detected 443 * 444 */ 445 enum prcmu_power_status { 446 PRCMU_SLEEP_OK = 0xf3, 447 PRCMU_DEEP_SLEEP_OK = 0xf6, 448 PRCMU_IDLE_OK = 0xf0, 449 PRCMU_DEEPIDLE_OK = 0xe3, 450 PRCMU_PRCMU2ARMPENDINGIT_ER = 0x91, 451 PRCMU_ARMPENDINGIT_ER = 0x93, 452 }; 453 454 /* 455 * Definitions for autonomous power management configuration. 456 */ 457 458 #define PRCMU_AUTO_PM_OFF 0 459 #define PRCMU_AUTO_PM_ON 1 460 461 #define PRCMU_AUTO_PM_POWER_ON_HSEM BIT(0) 462 #define PRCMU_AUTO_PM_POWER_ON_ABB_FIFO_IT BIT(1) 463 464 enum prcmu_auto_pm_policy { 465 PRCMU_AUTO_PM_POLICY_NO_CHANGE, 466 PRCMU_AUTO_PM_POLICY_DSP_OFF_HWP_OFF, 467 PRCMU_AUTO_PM_POLICY_DSP_OFF_RAMRET_HWP_OFF, 468 PRCMU_AUTO_PM_POLICY_DSP_CLK_OFF_HWP_OFF, 469 PRCMU_AUTO_PM_POLICY_DSP_CLK_OFF_HWP_CLK_OFF, 470 }; 471 472 /** 473 * struct prcmu_auto_pm_config - Autonomous power management configuration. 474 * @sia_auto_pm_enable: SIA autonomous pm enable. (PRCMU_AUTO_PM_{OFF,ON}) 475 * @sia_power_on: SIA power ON enable. (PRCMU_AUTO_PM_POWER_ON_* bitmask) 476 * @sia_policy: SIA power policy. (enum prcmu_auto_pm_policy) 477 * @sva_auto_pm_enable: SVA autonomous pm enable. (PRCMU_AUTO_PM_{OFF,ON}) 478 * @sva_power_on: SVA power ON enable. (PRCMU_AUTO_PM_POWER_ON_* bitmask) 479 * @sva_policy: SVA power policy. (enum prcmu_auto_pm_policy) 480 */ 481 struct prcmu_auto_pm_config { 482 u8 sia_auto_pm_enable; 483 u8 sia_power_on; 484 u8 sia_policy; 485 u8 sva_auto_pm_enable; 486 u8 sva_power_on; 487 u8 sva_policy; 488 }; 489 490 #ifdef CONFIG_MFD_DB8500_PRCMU 491 492 void db8500_prcmu_early_init(void); 493 int prcmu_set_rc_a2p(enum romcode_write); 494 enum romcode_read prcmu_get_rc_p2a(void); 495 enum ap_pwrst prcmu_get_xp70_current_state(void); 496 bool prcmu_has_arm_maxopp(void); 497 struct prcmu_fw_version *prcmu_get_fw_version(void); 498 int prcmu_release_usb_wakeup_state(void); 499 void prcmu_configure_auto_pm(struct prcmu_auto_pm_config *sleep, 500 struct prcmu_auto_pm_config *idle); 501 bool prcmu_is_auto_pm_enabled(void); 502 503 int prcmu_config_clkout(u8 clkout, u8 source, u8 div); 504 int prcmu_set_clock_divider(u8 clock, u8 divider); 505 int db8500_prcmu_config_hotdog(u8 threshold); 506 int db8500_prcmu_config_hotmon(u8 low, u8 high); 507 int db8500_prcmu_start_temp_sense(u16 cycles32k); 508 int db8500_prcmu_stop_temp_sense(void); 509 int prcmu_abb_read(u8 slave, u8 reg, u8 *value, u8 size); 510 int prcmu_abb_write(u8 slave, u8 reg, u8 *value, u8 size); 511 512 int prcmu_ac_wake_req(void); 513 void prcmu_ac_sleep_req(void); 514 void db8500_prcmu_modem_reset(void); 515 516 int db8500_prcmu_config_a9wdog(u8 num, bool sleep_auto_off); 517 int db8500_prcmu_enable_a9wdog(u8 id); 518 int db8500_prcmu_disable_a9wdog(u8 id); 519 int db8500_prcmu_kick_a9wdog(u8 id); 520 int db8500_prcmu_load_a9wdog(u8 id, u32 val); 521 522 void db8500_prcmu_system_reset(u16 reset_code); 523 int db8500_prcmu_set_power_state(u8 state, bool keep_ulp_clk, bool keep_ap_pll); 524 u8 db8500_prcmu_get_power_state_result(void); 525 void db8500_prcmu_enable_wakeups(u32 wakeups); 526 int db8500_prcmu_set_epod(u16 epod_id, u8 epod_state); 527 int db8500_prcmu_request_clock(u8 clock, bool enable); 528 void db8500_prcmu_config_abb_event_readout(u32 abb_events); 529 void db8500_prcmu_get_abb_event_buffer(void __iomem **buf); 530 int db8500_prcmu_config_esram0_deep_sleep(u8 state); 531 u16 db8500_prcmu_get_reset_code(void); 532 bool db8500_prcmu_is_ac_wake_requested(void); 533 int db8500_prcmu_set_arm_opp(u8 opp); 534 int db8500_prcmu_get_arm_opp(void); 535 int db8500_prcmu_set_ape_opp(u8 opp); 536 int db8500_prcmu_get_ape_opp(void); 537 int db8500_prcmu_request_ape_opp_100_voltage(bool enable); 538 int db8500_prcmu_get_ddr_opp(void); 539 540 u32 db8500_prcmu_read(unsigned int reg); 541 void db8500_prcmu_write(unsigned int reg, u32 value); 542 void db8500_prcmu_write_masked(unsigned int reg, u32 mask, u32 value); 543 544 #else /* !CONFIG_MFD_DB8500_PRCMU */ 545 db8500_prcmu_early_init(void)546 static inline void db8500_prcmu_early_init(void) {} 547 prcmu_set_rc_a2p(enum romcode_write code)548 static inline int prcmu_set_rc_a2p(enum romcode_write code) 549 { 550 return 0; 551 } 552 prcmu_get_rc_p2a(void)553 static inline enum romcode_read prcmu_get_rc_p2a(void) 554 { 555 return INIT; 556 } 557 prcmu_get_xp70_current_state(void)558 static inline enum ap_pwrst prcmu_get_xp70_current_state(void) 559 { 560 return AP_EXECUTE; 561 } 562 prcmu_has_arm_maxopp(void)563 static inline bool prcmu_has_arm_maxopp(void) 564 { 565 return false; 566 } 567 prcmu_get_fw_version(void)568 static inline struct prcmu_fw_version *prcmu_get_fw_version(void) 569 { 570 return NULL; 571 } 572 db8500_prcmu_set_ape_opp(u8 opp)573 static inline int db8500_prcmu_set_ape_opp(u8 opp) 574 { 575 return 0; 576 } 577 db8500_prcmu_get_ape_opp(void)578 static inline int db8500_prcmu_get_ape_opp(void) 579 { 580 return APE_100_OPP; 581 } 582 db8500_prcmu_request_ape_opp_100_voltage(bool enable)583 static inline int db8500_prcmu_request_ape_opp_100_voltage(bool enable) 584 { 585 return 0; 586 } 587 prcmu_release_usb_wakeup_state(void)588 static inline int prcmu_release_usb_wakeup_state(void) 589 { 590 return 0; 591 } 592 db8500_prcmu_get_ddr_opp(void)593 static inline int db8500_prcmu_get_ddr_opp(void) 594 { 595 return DDR_100_OPP; 596 } 597 prcmu_configure_auto_pm(struct prcmu_auto_pm_config * sleep,struct prcmu_auto_pm_config * idle)598 static inline void prcmu_configure_auto_pm(struct prcmu_auto_pm_config *sleep, 599 struct prcmu_auto_pm_config *idle) 600 { 601 } 602 prcmu_is_auto_pm_enabled(void)603 static inline bool prcmu_is_auto_pm_enabled(void) 604 { 605 return false; 606 } 607 prcmu_config_clkout(u8 clkout,u8 source,u8 div)608 static inline int prcmu_config_clkout(u8 clkout, u8 source, u8 div) 609 { 610 return 0; 611 } 612 prcmu_set_clock_divider(u8 clock,u8 divider)613 static inline int prcmu_set_clock_divider(u8 clock, u8 divider) 614 { 615 return 0; 616 } 617 db8500_prcmu_config_hotdog(u8 threshold)618 static inline int db8500_prcmu_config_hotdog(u8 threshold) 619 { 620 return 0; 621 } 622 db8500_prcmu_config_hotmon(u8 low,u8 high)623 static inline int db8500_prcmu_config_hotmon(u8 low, u8 high) 624 { 625 return 0; 626 } 627 db8500_prcmu_start_temp_sense(u16 cycles32k)628 static inline int db8500_prcmu_start_temp_sense(u16 cycles32k) 629 { 630 return 0; 631 } 632 db8500_prcmu_stop_temp_sense(void)633 static inline int db8500_prcmu_stop_temp_sense(void) 634 { 635 return 0; 636 } 637 prcmu_abb_read(u8 slave,u8 reg,u8 * value,u8 size)638 static inline int prcmu_abb_read(u8 slave, u8 reg, u8 *value, u8 size) 639 { 640 return -ENOSYS; 641 } 642 prcmu_abb_write(u8 slave,u8 reg,u8 * value,u8 size)643 static inline int prcmu_abb_write(u8 slave, u8 reg, u8 *value, u8 size) 644 { 645 return -ENOSYS; 646 } 647 prcmu_ac_wake_req(void)648 static inline int prcmu_ac_wake_req(void) 649 { 650 return 0; 651 } 652 prcmu_ac_sleep_req(void)653 static inline void prcmu_ac_sleep_req(void) {} 654 db8500_prcmu_modem_reset(void)655 static inline void db8500_prcmu_modem_reset(void) {} 656 db8500_prcmu_system_reset(u16 reset_code)657 static inline void db8500_prcmu_system_reset(u16 reset_code) {} 658 db8500_prcmu_set_power_state(u8 state,bool keep_ulp_clk,bool keep_ap_pll)659 static inline int db8500_prcmu_set_power_state(u8 state, bool keep_ulp_clk, 660 bool keep_ap_pll) 661 { 662 return 0; 663 } 664 db8500_prcmu_get_power_state_result(void)665 static inline u8 db8500_prcmu_get_power_state_result(void) 666 { 667 return 0; 668 } 669 db8500_prcmu_enable_wakeups(u32 wakeups)670 static inline void db8500_prcmu_enable_wakeups(u32 wakeups) {} 671 db8500_prcmu_set_epod(u16 epod_id,u8 epod_state)672 static inline int db8500_prcmu_set_epod(u16 epod_id, u8 epod_state) 673 { 674 return 0; 675 } 676 db8500_prcmu_request_clock(u8 clock,bool enable)677 static inline int db8500_prcmu_request_clock(u8 clock, bool enable) 678 { 679 return 0; 680 } 681 db8500_prcmu_config_esram0_deep_sleep(u8 state)682 static inline int db8500_prcmu_config_esram0_deep_sleep(u8 state) 683 { 684 return 0; 685 } 686 db8500_prcmu_config_abb_event_readout(u32 abb_events)687 static inline void db8500_prcmu_config_abb_event_readout(u32 abb_events) {} 688 db8500_prcmu_get_abb_event_buffer(void __iomem ** buf)689 static inline void db8500_prcmu_get_abb_event_buffer(void __iomem **buf) {} 690 db8500_prcmu_get_reset_code(void)691 static inline u16 db8500_prcmu_get_reset_code(void) 692 { 693 return 0; 694 } 695 db8500_prcmu_config_a9wdog(u8 num,bool sleep_auto_off)696 static inline int db8500_prcmu_config_a9wdog(u8 num, bool sleep_auto_off) 697 { 698 return 0; 699 } 700 db8500_prcmu_enable_a9wdog(u8 id)701 static inline int db8500_prcmu_enable_a9wdog(u8 id) 702 { 703 return 0; 704 } 705 db8500_prcmu_disable_a9wdog(u8 id)706 static inline int db8500_prcmu_disable_a9wdog(u8 id) 707 { 708 return 0; 709 } 710 db8500_prcmu_kick_a9wdog(u8 id)711 static inline int db8500_prcmu_kick_a9wdog(u8 id) 712 { 713 return 0; 714 } 715 db8500_prcmu_load_a9wdog(u8 id,u32 val)716 static inline int db8500_prcmu_load_a9wdog(u8 id, u32 val) 717 { 718 return 0; 719 } 720 db8500_prcmu_is_ac_wake_requested(void)721 static inline bool db8500_prcmu_is_ac_wake_requested(void) 722 { 723 return 0; 724 } 725 db8500_prcmu_set_arm_opp(u8 opp)726 static inline int db8500_prcmu_set_arm_opp(u8 opp) 727 { 728 return 0; 729 } 730 db8500_prcmu_get_arm_opp(void)731 static inline int db8500_prcmu_get_arm_opp(void) 732 { 733 return 0; 734 } 735 db8500_prcmu_read(unsigned int reg)736 static inline u32 db8500_prcmu_read(unsigned int reg) 737 { 738 return 0; 739 } 740 db8500_prcmu_write(unsigned int reg,u32 value)741 static inline void db8500_prcmu_write(unsigned int reg, u32 value) {} 742 db8500_prcmu_write_masked(unsigned int reg,u32 mask,u32 value)743 static inline void db8500_prcmu_write_masked(unsigned int reg, u32 mask, 744 u32 value) {} 745 746 #endif /* !CONFIG_MFD_DB8500_PRCMU */ 747 748 #endif /* __MFD_DB8500_PRCMU_H */ 749
