Home
last modified time | relevance | path

Searched refs:Opcode (Results 1 – 8 of 8) sorted by relevance

/Linux-v5.10/Documentation/firmware-guide/acpi/
Dmethod-tracing.rst86 [ 0.186630] exdebug-0398 ex_trace_point : Opcode Begin [0xf5905c88:If] execution.
87 [ 0.186820] exdebug-0398 ex_trace_point : Opcode Begin [0xf5905cc0:LEqual] execution.
88 …[ 0.187010] exdebug-0398 ex_trace_point : Opcode Begin [0xf5905a20:-NamePath-] executi…
89 …[ 0.187214] exdebug-0398 ex_trace_point : Opcode End [0xf5905a20:-NamePath-] execution.
90 [ 0.187407] exdebug-0398 ex_trace_point : Opcode Begin [0xf5905f60:One] execution.
91 [ 0.187594] exdebug-0398 ex_trace_point : Opcode End [0xf5905f60:One] execution.
92 [ 0.187789] exdebug-0398 ex_trace_point : Opcode End [0xf5905cc0:LEqual] execution.
93 [ 0.187980] exdebug-0398 ex_trace_point : Opcode Begin [0xf5905cc0:Return] execution.
94 [ 0.188146] exdebug-0398 ex_trace_point : Opcode Begin [0xf5905f60:One] execution.
95 [ 0.188334] exdebug-0398 ex_trace_point : Opcode End [0xf5905f60:One] execution.
[all …]
/Linux-v5.10/drivers/media/pci/ngene/
Dngene-i2c.c36 com.cmd.hdr.Opcode = CMD_I2C_READ; in ngene_command_i2c_read()
64 com.cmd.hdr.Opcode = CMD_I2C_WRITE; in ngene_command_i2c_write()
Dngene-core.c262 if (com->cmd.hdr.Opcode == CMD_FWLOAD_PREPARE) { in ngene_command_mutex()
271 } else if (com->cmd.hdr.Opcode == CMD_FWLOAD_FINISH) { in ngene_command_mutex()
305 com->cmd.hdr.Opcode, dev->prev_cmd); in ngene_command_mutex()
309 if (com->cmd.hdr.Opcode == CMD_FWLOAD_FINISH) in ngene_command_mutex()
312 dev->prev_cmd = com->cmd.hdr.Opcode; in ngene_command_mutex()
340 com.cmd.hdr.Opcode = CMD_FWLOAD_PREPARE; in ngene_command_load_firmware()
356 com.cmd.hdr.Opcode = CMD_FWLOAD_FINISH; in ngene_command_load_firmware()
371 com.cmd.hdr.Opcode = CMD_CONFIGURE_BUFFER; in ngene_command_config_buf()
386 com.cmd.hdr.Opcode = CMD_CONFIGURE_FREE_BUFFER; in ngene_command_config_free_buf()
402 com.cmd.hdr.Opcode = CMD_SET_GPIO_PIN; in ngene_command_gpio_set()
[all …]
Dngene.h249 u8 Opcode; member
/Linux-v5.10/Documentation/powerpc/
Dpapr_hcalls.rst38 done via the instruction **HVCS** that expects the Opcode for hcall is set in *r3*
/Linux-v5.10/Documentation/sparc/oradax/
Doracle-dax.rst255 - Opcode, which must be one of the documented allowable commands
/Linux-v5.10/arch/x86/lib/
Dx86-opcode-map.txt1 # x86 Opcode Maps
7 #<Opcode maps>
/Linux-v5.10/tools/arch/x86/lib/
Dx86-opcode-map.txt1 # x86 Opcode Maps
7 #<Opcode maps>