| /Linux-v5.10/drivers/video/fbdev/omap/ |
| D | lcd_h3.c | 23 r = tps65010_set_gpio_out_value(GPIO1, HIGH); in h3_panel_enable()
25 r = tps65010_set_gpio_out_value(GPIO2, HIGH); in h3_panel_enable()
|
| /Linux-v5.10/Documentation/devicetree/bindings/media/i2c/ |
| D | ov7670.txt | 13 - hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
14 - vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
|
| D | st,st-mipid02.txt | 45 - hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
47 - vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
|
| D | ov5640.txt | 38 - hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
39 - vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
|
| D | tvp5150.txt | 44 - hsync-active: Active state of the HSYNC signal. Must be <1> (HIGH).
45 - vsync-active: Active state of the VSYNC signal. Must be <1> (HIGH).
|
| /Linux-v5.10/arch/arm64/boot/dts/renesas/ |
| D | hihope-rzg2-ex-lvds.dtsi | 21 * When GP1_20 is HIGH LVDS0 is connected to the LT8918L
|
| /Linux-v5.10/include/linux/mfd/ |
| D | tps65010.h | 122 #define HIGH 1 macro
|
| /Linux-v5.10/Documentation/devicetree/bindings/clock/ |
| D | silabs,si5351.txt | 55 1 = clock output is driven HIGH when disabled
56 2 = clock output is FLOATING (HIGH-Z) when disabled
|
| /Linux-v5.10/arch/arm/boot/dts/ |
| D | rk3228-evb.dts | 63 rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
|
| D | rk3288-rock2-som.dtsi | 251 rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
|
| /Linux-v5.10/drivers/s390/crypto/ |
| D | zcrypt_msgtype6.h | 107 #define HIGH 500 macro
|
| /Linux-v5.10/Documentation/userspace-api/media/cec/ |
| D | cec-ioc-dqevent.rst | 160 * .. _`CEC-EVENT-PIN-CEC-HIGH`:
176 * .. _`CEC-EVENT-PIN-HPD-HIGH`:
194 * .. _`CEC-EVENT-PIN-5V-HIGH`:
|
| /Linux-v5.10/Documentation/devicetree/bindings/regulator/ |
| D | max8973-regulator.txt | 21 1 for HIGH and 0 for LOW.
|
| /Linux-v5.10/Documentation/devicetree/bindings/mfd/ |
| D | max77620.txt | 122 GPIO1/nRST_IO pins are HIGH only if all rails
123 that have POK control enabled are HIGH.
|
| D | tps6507x.txt | 30 1: If defdcdc pin of DCDC2/DCDC3 is driven HIGH.
|
| /Linux-v5.10/drivers/nfc/st95hf/ |
| D | core.c | 77 #define HIGH 1 macro
455 gpio_set_value(st95con->enable_gpio, HIGH); in st95hf_send_st95enable_negativepulse()
467 gpio_set_value(st95con->enable_gpio, HIGH); in st95hf_send_st95enable_negativepulse()
|
| /Linux-v5.10/Documentation/devicetree/bindings/thermal/ |
| D | rockchip-thermal.txt | 33 1:HIGH.
|
| /Linux-v5.10/arch/arm64/boot/dts/rockchip/ |
| D | rk3368-evb.dtsi | 221 rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */
|
| /Linux-v5.10/Documentation/leds/ |
| D | leds-lm3556.rst | 24 or by pulling the STROBE pin HIGH.
|
| /Linux-v5.10/drivers/net/ieee802154/ |
| D | cc2520.c | 26 #define HIGH 1 macro
1170 gpio_set_value(pdata.vreg, HIGH); in cc2520_probe()
1173 gpio_set_value(pdata.reset, HIGH); in cc2520_probe()
|
| /Linux-v5.10/Documentation/driver-api/iio/ |
| D | buffers.rst | 60 |D11|D10|D9 |D8 |D7 |D6 |D5 |D4 | (HIGH byte, address 0x07)
|
| /Linux-v5.10/arch/arm/mach-omap1/ |
| D | board-osk.c | 208 tps65010_set_gpio_out_value(GPIO2, HIGH); in osk_tps_setup()
|
| /Linux-v5.10/Documentation/devicetree/bindings/pinctrl/ |
| D | pinctrl-max77620.txt | 66 master FPS input event set to HIGH.
|
| /Linux-v5.10/Documentation/devicetree/bindings/media/ |
| D | video-interfaces.txt | 477 - hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
478 - vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
488 LOW/HIGH respectively.
|
| /Linux-v5.10/tools/power/cpupower/bench/ |
| D | README-BENCH | 114 -p, --prio=<priority> scheduler priority, HIGH, LOW or DEFAULT
|
