/Linux-v5.10/drivers/gpu/drm/amd/amdgpu/ |
D | amdgpu_afmt.c | 51 static void amdgpu_afmt_calc_cts(uint32_t clock, int *CTS, int *N, int freq) in amdgpu_afmt_calc_cts() argument 82 *CTS = cts; in amdgpu_afmt_calc_cts() 85 *N, *CTS, freq); in amdgpu_afmt_calc_cts()
|
/Linux-v5.10/arch/arm/boot/dts/ |
D | am335x-netcom-plus-2xx.dts | 25 AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLDOWN, MUX_MODE0) /* CTS */ 38 AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLDOWN, MUX_MODE2) /* CTS */
|
D | imx6ul-ccimx6ulsbcpro.dts | 62 /* CAN2 is multiplexed with UART2 RTS/CTS */ 201 /* UART2 RTS/CTS muxed with CAN2 */ 209 /* UART3 RTS/CTS muxed with CAN 1 */
|
D | ste-dbx5x0-pinctrl.dtsi | 17 pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */ 28 pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */ 75 pins = "GPIO6_AF6"; /* CTS */ 86 pins = "GPIO6_AF6"; /* CTS */
|
D | stm32mp157a-iot-box.dts | 57 /* Note: HW flow control is broken, hence using custom CTS/RTS gpios */
|
/Linux-v5.10/Documentation/devicetree/bindings/soc/fsl/cpm_qe/ |
D | serial.txt | 14 CTS, RTS, DCD, DSR, DTR, and RI.
|
/Linux-v5.10/Documentation/devicetree/bindings/serial/ |
D | microchip,pic32-uart.txt | 14 - cts-gpios: CTS pin for UART
|
D | cirrus,clps711x-uart.txt | 11 - {rts,cts,dtr,dsr,rng,dcd}-gpios: specify a GPIO for RTS/CTS/DTR/DSR/RI/DCD
|
D | cdns,uart.txt | 16 - cts-override : Override the CTS modem status signal. This signal will
|
D | sirf-uart.txt | 14 - cts-gpios: CTS pin for USP-based UART if uart-has-rtscts is true
|
/Linux-v5.10/Documentation/usb/ |
D | iuu_phoenix.rst | 44 0=none, 1=CD, 2=!CD, 3=DSR, 4=!DSR, 5=CTS, 6=!CTS, 7=RING, 8=!RING (int)
|
/Linux-v5.10/arch/arm64/boot/dts/allwinner/ |
D | sun50i-a64-orangepi-win.dts | 382 /* On Pi-2 connector, RTS/CTS optional */ 389 /* On Pi-2 connector, RTS/CTS optional */ 396 /* On Pi-2 connector (labeled for SPI1), RTS/CTS optional */
|
D | sun50i-a64-pine64.dts | 285 /* On Wifi/BT connector, with RTS/CTS */ 306 /* On Euler connector, RTS/CTS optional */
|
D | sun50i-a64-sopine-baseboard.dts | 191 /* On Euler connector, RTS/CTS optional */
|
/Linux-v5.10/arch/arm64/boot/dts/freescale/ |
D | imx8mq-hummingboard-pulse.dts | 166 * reconfigured to enable RTS/CTS on UART3 209 * Header. To use RTS/CTS on UART3 comment them out
|
/Linux-v5.10/drivers/tty/ |
D | nozomi.c | 242 unsigned int CTS:1; member 303 unsigned int CTS:1; member 935 if (old_ctrl.CTS == 1 && ctrl_dl.CTS == 0) { in receive_flow_control() 940 } else if (old_ctrl.CTS == 0 && ctrl_dl.CTS == 1) { in receive_flow_control() 958 if (old_ctrl.CTS != ctrl_dl.CTS) in receive_flow_control() 1635 if (port->ctrl_dl.CTS) { in ntty_write() 1685 | (ctrl_dl->CTS ? TIOCM_CTS : 0); in ntty_tiocmget()
|
/Linux-v5.10/drivers/net/hamradio/ |
D | z8530.h | 178 #define CTS 0x20 /* CTS */ macro
|
/Linux-v5.10/drivers/tty/serial/ |
D | zs.h | 234 #define CTS 0x20 /* CTS */ macro
|
D | ip22zilog.h | 214 #define CTS 0x20 /* CTS */ macro
|
D | sunzilog.h | 218 #define CTS 0x20 /* CTS */ macro
|
/Linux-v5.10/Documentation/devicetree/bindings/net/nfc/ |
D | nfcmrvl.txt | 16 - flow-control: Specifies that the chip is using RTS/CTS.
|
/Linux-v5.10/drivers/media/i2c/ |
D | ad9389b.c | 404 u32 CTS; in ad9389b_log_status() local 407 CTS = (ad9389b_rd(sd, 0x07) & 0xf) << 16 | in ad9389b_log_status() 411 CTS = (ad9389b_rd(sd, 0x04) & 0xf) << 16 | in ad9389b_log_status() 419 manual_cts ? "manual" : "automatic", N, CTS); in ad9389b_log_status()
|
/Linux-v5.10/Documentation/arm/sa1100/ |
D | assabet.rst | 253 Radio: TX, RX, CTS, DSR, DCD, RI 255 - COM: TX, RX, CTS, DSR, DCD, RTS, DTR, PM 294 - COM1,2: TX, RX, CTS, DSR, DCD, RTS, DTR
|
/Linux-v5.10/drivers/gpu/drm/radeon/ |
D | radeon_audio.c | 549 static void radeon_audio_calc_cts(unsigned int clock, int *CTS, int *N, int freq) in radeon_audio_calc_cts() argument 580 *CTS = cts; in radeon_audio_calc_cts() 583 *N, *CTS, freq); in radeon_audio_calc_cts()
|
/Linux-v5.10/Documentation/devicetree/bindings/display/bridge/ |
D | sii902x.txt | 30 HDMI audio CTS values. This property follows
|