| /Linux-v5.10/drivers/regulator/ |
| D | lp8788-buck.c | 83 BUCK2, enumerator
155 case BUCK2: in lp8788_set_dvs()
172 case BUCK2: in lp8788_get_buck_dvs_ctrl_mode()
224 case BUCK2: in lp8788_select_buck_vout_addr()
382 .id = BUCK2,
441 case BUCK2: in lp8788_dvs_gpio_request()
467 if (id > BUCK2) in lp8788_init_dvs()
475 (id == BUCK2 && !pdata->buck2_dvs)) in lp8788_init_dvs()
|
| D | tps65086-regulator.c | 25 enum tps65086_regulators { BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, LDOA1, enumerator
130 TPS65086_REGULATOR("BUCK2", "buck2", BUCK2, 0x80, TPS65086_BUCK2CTRL,
175 case BUCK2: in tps65086_of_parse_cb()
|
| D | mcp16502.c | 107 BUCK2, enumerator
405 MCP16502_REGULATOR("VDD_DDR", BUCK2, b234_ranges, mcp16502_buck_ops),
|
| D | da9052-regulator.c | 331 DA9052_DCDC(BUCK2, buck2, 25, 500, 2075, 6, 6, DA9052_SUPPLY_VBPROGO),
348 DA9052_DCDC(BUCK2, buck2, 25, 500, 2075, 6, 6, DA9052_SUPPLY_VBPROGO),
|
| D | da903x-regulator.c | 371 DA9030_DVC(BUCK2, 850, 1625, 25, BUCK2DVM1, 5, BUCK2DVM1, 7, RCTL11, 0),
395 DA9034_DVC(BUCK2, 725, 1500, 25, CDTV2, 5, VCC1, 2, OVER1, 1),
|
| D | stpmic1_regulator.c | 365 .desc = REG_BUCK(BUCK2, buck2),
524 MATCH(buck2, BUCK2),
|
| D | 88pm8607.c | 293 PM8607_DVC(BUCK2, GO, BIT(1), SUPPLIES_EN11, 1),
|
| D | 88pm800-regulator.c | 200 PM800_BUCK(buck2, BUCK2, BUCK_ENA, 1, 1200000, buck2_5_volt_range, 0x73),
|
| D | pv88090-regulator.c | 210 PV88090_BUCK(PV88090, BUCK2, 600000, 6250, 1393750,
|
| D | ltc3676.c | 226 LTC3676_LINEAR_REG(SW2, sw2, BUCK2, DVB2A),
|
| D | mt6360-regulator.c | 356 MT6360_REGULATOR_DESC(BUCK2, BUCK2_VIN, 0x127, 0x40, 0x120, 0xff, 0x127, 0x30, 0x127, 0x04,
|
| /Linux-v5.10/Documentation/devicetree/bindings/regulator/ |
| D | pv88090.txt | 11 BUCK1, BUCK2, BUCK3, LDO1, and LDO2.
34 BUCK2 {
|
| D | pv88080.txt | 17 BUCK1, BUCK2, BUCK3 and HVBUCK.
39 BUCK2 {
|
| D | rohm,bd70528-regulator.txt | 12 BUCK1, BUCK2, BUCK3, LDO1, LDO2, LDO3, LED_LDO1, LED_LDO2
26 buck2: BUCK2 {
|
| D | samsung,s2mpa01.txt | 21 - Example: BUCK1, BUCK2, BUCK9
70 buck2_reg: BUCK2 {
|
| D | samsung,s2mps11.txt | 31 - Example: BUCK1, BUCK2, BUCK9
93 buck2_reg: BUCK2 {
|
| D | lp872x.txt | 18 bit[4]: BUCK2 enable control. 1 = enable, 0 = disable
19 bit[3]: BUCK2 output voltage register address. 1 = 0Ah, 0 = 0Bh
|
| D | max77802.txt | 13 - inb2-supply: The input supply for BUCK2
|
| /Linux-v5.10/Documentation/devicetree/bindings/mfd/ |
| D | da9055.txt | 34 buck2 : regulator BUCK2
61 buck2: BUCK2 {
|
| D | rohm,bd70528-pmic.txt | 59 buck2: BUCK2 {
|
| D | samsung,sec-core.txt | 77 buck2_reg: BUCK2 {
|
| /Linux-v5.10/arch/arm64/boot/dts/freescale/ |
| D | imx8mn-evk.dts | 36 buck2: BUCK2 {
37 regulator-name = "BUCK2";
|
| D | imx8mn-ddr4-evk.dts | 72 buck2_reg: BUCK2 {
|
| /Linux-v5.10/arch/arm/boot/dts/ |
| D | dra71-evm.dts | 102 /* FB_B1 -> LP8733-BUCK2 - VPO_S2_AVS - VDD_DSP_AVS (DSP/eve/iva) */
148 /* FB_B1 -> LP8732-BUCK2 - VPO_S4_DDR - VDD_DDR_1V35 */
|
| D | pxa910-dkb.dts | 48 BUCK2 {
|
