Searched refs:Active (Results 1 – 25 of 97) sorted by relevance
1234
| /Linux-v5.10/Documentation/fb/ |
| D | viafb.modes | 21 # Active Time 25.422 us 15.253 ms
46 # Active Time 20.317 us 12.800 ms
67 # Active Time 17.778 us 11.093 ms
88 # Active Time 14.827 us 9.430 ms
109 # Active Time 12.212 us 7.767 ms
130 # Active Time 26.786 us 16.000 ms
151 # Active Time 27.044 us 16.097 ms
172 # Active Time 22.040 us 16.080 ms
193 # Active Time 20.000 us 15.840 ms
215 # Active Time 16.162 us 12.800 ms
[all …]
|
| /Linux-v5.10/Documentation/devicetree/bindings/media/i2c/ |
| D | tvp7002.txt | 19 - sync-on-green-active: Active state of Sync-on-green signal property of the
21 0 = Normal Operation (Active Low, Default)
24 - field-even-active: Active-high Field ID output polarity control of the bus.
27 0 = Normal Operation (Active Low, Default)
|
| D | aptina,mt9v111.txt | 20 - enable-gpios: output enable signal, pin name "OE#". Active low.
22 Active high.
23 - reset-gpios: chip reset signal, pin name "RESET#". Active low.
|
| D | ov9650.txt | 11 Active is high.
13 Active is high.
|
| D | mt9m001.txt | 14 Active low.
16 Active high.
|
| D | ov2659.txt | 17 Active high with internal pull down resistor.
19 Active low with internal pull up resistor.
|
| D | ov7740.txt | 19 if any. Active low with pull-ip resistor.
21 if any. Active high with pull-down resistor.
|
| D | ov7670.txt | 18 Active is low.
20 Active is high.
|
| D | tvp5150.txt | 44 - hsync-active: Active state of the HSYNC signal. Must be <1> (HIGH).
45 - vsync-active: Active state of the VSYNC signal. Must be <1> (HIGH).
|
| /Linux-v5.10/arch/arm/boot/dts/ |
| D | sun8i-s3-pinecube.dts | 73 hsync-active = <1>; /* Active high */
74 vsync-active = <0>; /* Active low */
75 data-active = <1>; /* Active high */
124 hsync-active = <1>; /* Active high */
125 vsync-active = <0>; /* Active low */
126 data-active = <1>; /* Active high */
|
| /Linux-v5.10/Documentation/devicetree/bindings/gpio/ |
| D | cirrus,clps711x-mctrl-gpio.txt | 8 0 = Active high,
9 1 = Active low.
|
| D | gpio-74xx-mmio.txt | 21 0 = Active High,
22 1 = Active Low.
|
| D | rockchip,rk3328-grf-gpio.txt | 16 0 = Active high,
17 1 = Active low.
|
| D | nvidia,tegra186-gpio.txt | 110 - 0: Active-high (normal).
111 - 1: Active-low (inverted).
126 - 4: Active high level-sensitive.
127 - 8: Active low level-sensitive.
|
| /Linux-v5.10/arch/arm64/boot/dts/allwinner/ |
| D | sun50i-a64-amarula-relic.dts | 50 hsync-active = <1>; /* Active high */
51 vsync-active = <0>; /* Active low */
52 data-active = <1>; /* Active high */
90 hsync-active = <1>; /* Active high */
91 vsync-active = <0>; /* Active low */
92 data-active = <1>; /* Active high */
|
| D | sun50i-a64-pinetab.dts | 65 hsync-active = <1>; /* Active high */
66 vsync-active = <0>; /* Active low */
67 data-active = <1>; /* Active high */
128 hsync-active = <1>; /* Active high */
129 vsync-active = <0>; /* Active low */
130 data-active = <1>; /* Active high */
|
| /Linux-v5.10/Documentation/devicetree/bindings/media/ |
| D | pxa-camera.txt | 37 hsync-active = <0>; /* Active low */
38 vsync-active = <0>; /* Active low */
|
| /Linux-v5.10/drivers/block/ |
| D | umem.c | 121 int Active, Ready; member
260 page = &card->mm_pages[card->Active]; in mm_start_io()
262 card->Active, page->headcnt, page->cnt - 1); in mm_start_io()
313 if (card->Active == -1 && in activate()
315 card->Active = card->Ready; in activate()
320 } while (card->Active == -1 && add_bio(card)); in activate()
422 if (card->Active < 0) in process_page()
424 page = &card->mm_pages[card->Active]; in process_page()
488 card->Active = -1; in process_page()
727 if (card->Active >= 0) in check_all_batteries()
[all …]
|
| /Linux-v5.10/Documentation/devicetree/bindings/power/reset/ |
| D | gpio-poweroff.txt | 22 low to power down the board set it to "Active Low", otherwise set
23 gpio to "Active High".
|
| D | gpio-restart.txt | 24 low to reset the board set it to "Active Low", otherwise set
25 gpio to "Active High".
|
| /Linux-v5.10/Documentation/devicetree/bindings/leds/irled/ |
| D | gpio-ir-tx.txt | 7 Documentation/devicetree/bindings/gpio/gpio.txt. Active low LEDs
|
| /Linux-v5.10/Documentation/devicetree/bindings/fpga/ |
| D | lattice-ice40-fpga-mgr.txt | 8 - reset-gpios: Active-low GPIO output connected to CRESET_B pin. Note
|
| /Linux-v5.10/Documentation/devicetree/bindings/spi/ |
| D | spi_atmel.txt | 8 Chip Select Active After Transfer feature).
|
| /Linux-v5.10/drivers/staging/iio/meter/ |
| D | Kconfig | 5 menu "Active energy metering IC"
|
| /Linux-v5.10/arch/powerpc/boot/dts/ |
| D | mvme5100.dts | 61 interrupts = <1 1>; // IRQ1 Level Active Low.
72 interrupts = <1 1>; // IRQ1 Level Active Low.
|
1234
