| /Linux-v4.19/drivers/net/wireless/ti/wl18xx/ |
| D | cmd.c | 58 wl1271_error("invalid channel switch band: %d", in wl18xx_cmd_channel_switch()
77 wl1271_error("failed to send channel switch command"); in wl18xx_cmd_channel_switch()
105 wl1271_error("failed to send smart config start command"); in wl18xx_cmd_smart_config_start()
130 wl1271_error("failed to send smart config stop command"); in wl18xx_cmd_smart_config_stop()
150 wl1271_error("invalid group key size: %d", key_len); in wl18xx_cmd_smart_config_set_group_key()
166 wl1271_error("failed to send smart config set group key cmd"); in wl18xx_cmd_smart_config_set_group_key()
198 wl1271_error("failed to send cac command"); in wl18xx_cmd_set_cac()
224 wl1271_error("failed to send radar detection debug command"); in wl18xx_cmd_radar_detection_debug()
250 wl1271_error("failed to send dfs master restart command"); in wl18xx_cmd_dfs_master_restart()
|
| D | scan.c | 124 wl1271_error("2.4GHz PROBE request template failed"); in wl18xx_scan_send()
141 wl1271_error("5GHz PROBE request template failed"); in wl18xx_scan_send()
150 wl1271_error("SCAN failed"); in wl18xx_scan_send()
267 wl1271_error("2.4GHz PROBE request template failed"); in wl18xx_scan_sched_scan_config()
284 wl1271_error("5GHz PROBE request template failed"); in wl18xx_scan_sched_scan_config()
293 wl1271_error("SCAN failed"); in wl18xx_scan_sched_scan_config()
320 wl1271_error("failed to alloc memory to send sched scan stop"); in __wl18xx_scan_stop()
329 wl1271_error("failed to send sched scan stop command"); in __wl18xx_scan_stop()
|
| D | tx.c | 38 wl1271_error("last Tx rate invalid: %d", fw_rate); in wl18xx_get_last_tx_rate()
172 wl1271_error("invalid desc release index %d", in wl18xx_tx_immediate_complete()
|
| D | main.c | 1414 wl1271_error("could not get configuration binary %s: %d", in wl18xx_load_conf_file()
1420 wl1271_error("%s configuration binary size is wrong, expected %zu got %zu", in wl18xx_load_conf_file()
1429 wl1271_error("configuration binary file magic number mismatch, " in wl18xx_load_conf_file()
1437 wl1271_error("configuration binary file version not supported, " in wl18xx_load_conf_file()
1478 wl1271_error("wl18xx_plt_init: PLT FEM_DETECT not supported"); in wl18xx_plt_init()
1967 wl1271_error("invalid board type '%s'", in wl18xx_setup()
1974 wl1271_error("invalid board type '%d'", in wl18xx_setup()
2007 wl1271_error("invalid ht_mode '%s'", ht_mode_param); in wl18xx_setup()
2060 wl1271_error("can't allocate hw"); in wl18xx_probe()
|
| /Linux-v4.19/drivers/net/wireless/ti/wlcore/ |
| D | boot.c | 130 wl1271_error("Your WiFi FW version (%u.%u.%u.%u.%u) is invalid.\n" in wlcore_validate_fw_ver()
190 wl1271_error("firmware length not multiple of four"); in wl1271_boot_upload_firmware_chunk()
196 wl1271_error("allocation for firmware upload chunk failed"); in wl1271_boot_upload_firmware_chunk()
295 wl1271_error("NVS file is needed during boot"); in wlcore_boot_upload_nvs()
319 wl1271_error("%s size is not as expected: %zu != %zu", in wlcore_boot_upload_nvs()
338 wl1271_error("%s size is not as expected: %zu != %zu", in wlcore_boot_upload_nvs()
439 wl1271_error("nvs data is malformed"); in wlcore_boot_upload_nvs()
465 wl1271_error("chip id doesn't match after firmware boot"); in wlcore_boot_run_firmware()
478 wl1271_error("error reading hardware complete " in wlcore_boot_run_firmware()
493 wl1271_error("timeout waiting for the hardware to " in wlcore_boot_run_firmware()
[all …]
|
| D | cmd.c | 98 wl1271_error("command complete timeout"); in __wlcore_cmd_send()
149 wl1271_error("command execute failure %d", ret); in wlcore_cmd_send_failsafe()
269 wl1271_error("failed to initiate cmd role enable"); in wl12xx_cmd_role_enable()
302 wl1271_error("failed to initiate cmd role disable"); in wl12xx_cmd_role_disable()
468 wl1271_error("failed to initiate cmd role enable"); in wl12xx_cmd_role_start_dev()
508 wl1271_error("failed to initiate cmd role stop"); in wl12xx_cmd_role_stop_dev()
578 wl1271_error("failed to initiate cmd role start sta"); in wl12xx_cmd_role_start_sta()
619 wl1271_error("failed to initiate cmd role stop sta"); in wl12xx_cmd_role_stop_sta()
646 wl1271_error("got a null SSID from beacon/bss"); in wl12xx_cmd_role_start_ap()
723 wl1271_error("failed to initiate cmd role start ap"); in wl12xx_cmd_role_start_ap()
[all …]
|
| D | sysfs.c | 157 wl1271_error("failed to create sysfs file bt_coex_state"); in wlcore_sysfs_init()
164 wl1271_error("failed to create sysfs file hw_pg_ver"); in wlcore_sysfs_init()
171 wl1271_error("failed to create sysfs file fwlog"); in wlcore_sysfs_init()
|
| D | ps.c | 45 wl1271_error("couldn't set wake up conditions"); in wl1271_ps_set_mode()
147 wl1271_error("could not find sta %pM for starting ps", in wl12xx_ps_link_start()
178 wl1271_error("could not find sta %pM for ending ps", in wl12xx_ps_link_end()
|
| D | rx.c | 138 wl1271_error("Invalid packet arrived from HW. length %d", in wl1271_rx_handle_data()
172 wl1271_error("Couldn't allocate RX frame"); in wl1271_rx_handle_data()
328 wl1271_error("Failed to %s rx data filter %d (err=%d)", in wl1271_rx_filter_enable()
|
| D | event.c | 56 wl1271_error("Fail to allocate fw logger memory"); in wlcore_event_fw_logger()
64 wl1271_error("Fail to read logger buffer, error_id = %d", in wlcore_event_fw_logger()
100 wl1271_error("Calculate of clear addr Clear = %x, write = %x", in wlcore_event_fw_logger()
|
| D | main.c | 316 wl1271_error("Tx stuck (in FW) for %d ms. Starting recovery", in wl12xx_tx_watchdog_work()
338 wl1271_error("Unknown fwlog parameter %s", fwlog_param); in wlcore_adjust_conf()
581 wl1271_error("HW watchdog interrupt received! starting recovery."); in wlcore_irq_locked()
590 wl1271_error("SW watchdog interrupt received! " in wlcore_irq_locked()
772 wl1271_error("could not get firmware %s: %d", fw_name, ret); in wl12xx_fetch_firmware()
777 wl1271_error("firmware size is not multiple of 32 bits: %zu", in wl12xx_fetch_firmware()
789 wl1271_error("could not allocate memory for the firmware"); in wl12xx_fetch_firmware()
1111 wl1271_error("cannot go into PLT state because not " in wl1271_plt_start()
1152 wl1271_error("firmware boot in PLT mode failed despite %d retries", in wl1271_plt_start()
1183 wl1271_error("cannot power down because not in PLT " in wl1271_plt_stop()
[all …]
|
| D | debug.h | 64 #define wl1271_error(fmt, arg...) \ macro
|
| D | acx.c | 84 wl1271_error("could not configure sleep_auth to %d: %d", in wl1271_acx_sleep_auth()
148 wl1271_error("Couldn't set HW encryption"); in wl1271_acx_feature_cfg()
1018 wl1271_error("couldn't allocate target memory map"); in wl1271_acx_init_mem_config()
1026 wl1271_error("couldn't retrieve firmware memory map"); in wl1271_acx_init_mem_config()
|
| D | scan.c | 475 wl1271_error("cmd sched scan ssid list failed"); in wlcore_scan_sched_scan_ssid_list()
|
| D | tx.c | 385 wl1271_error("discarding null skb"); in wl1271_prepare_tx_frame()
390 wl1271_error("invalid hlid. dropping skb 0x%p", skb); in wl1271_prepare_tx_frame()
|
| /Linux-v4.19/drivers/net/wireless/ti/wl12xx/ |
| D | scan.c | 165 wl1271_error("PROBE request template failed"); in wl1271_scan_send()
173 wl1271_error("trigger scan to failed for hw scan"); in wl1271_scan_send()
181 wl1271_error("SCAN failed"); in wl1271_scan_send()
210 wl1271_error("cmd stop_scan failed"); in wl12xx_scan_stop()
295 wl1271_error("invalid scan state"); in wl1271_scan_stm()
374 wl1271_error("scan channel list is empty"); in wl1271_scan_sched_scan_config()
392 wl1271_error("2.4GHz PROBE request template failed"); in wl1271_scan_sched_scan_config()
409 wl1271_error("5GHz PROBE request template failed"); in wl1271_scan_sched_scan_config()
419 wl1271_error("SCAN configuration failed"); in wl1271_scan_sched_scan_config()
452 wl1271_error("failed to send scan start command"); in wl1271_scan_sched_scan_start()
[all …]
|
| D | main.c | 1077 wl1271_error("soft reset timeout"); in wl1271_boot_soft_reset()
1840 wl1271_error("Invalid ref_clock frequency (%d Hz, %s)", in wl12xx_setup()
1861 wl1271_error("Invalid fref parameter %s", fref_param); in wl12xx_setup()
1869 wl1271_error("Invalid tcxo_clock frequency (%d Hz)", in wl12xx_setup()
1892 wl1271_error("Invalid tcxo parameter %s", tcxo_param); in wl12xx_setup()
1912 wl1271_error("can't allocate hw"); in wl12xx_probe()
|
| D | cmd.c | 314 wl1271_error("failed to send channel switch command"); in wl12xx_cmd_channel_switch()
|
